REVISION Z
C
NOTES:
1.
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE TO BE 16 OZ FOR TERMINALS, 12 OZ FOR WELD TABS,
AND 8 OZ FOR LOCKING CLIPS.
3. MEASURED FROM BEND.
4. MAXIMUM TERMINAL BURR: .003 [.08]
5. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005 [.13]
6. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
TFM-1XX-XX-X-S-XX
No OF POSITIONS
ALL POSITIONS AVAILABLE
-02 THRU -50
OPTION
-A: ALIGNMENT PIN (USE TFM-XX-S-01-A)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG. 5 SHEET 2)
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG. 7 SHEET 3) (SEE NOTE 6)
-P: PICK AND PLACE PAD (USE PPP-15)
(SEE FIG. 6 SHEET 2)
(NOT AVAILABLE -03, -04 & -05 POSITIONS)
-K: POLYIMIDE FILM (SEE FIG. 3 SHEET 2)
(USE K-500-300)
-WT: WELD TABS (USE WT-25-07-T)
(SEE FIG. 4 SHEET 2)
(AVAILABLE ON -02 THRU -30 POS ONLY)
(NOT AVAILABLE WITH
-A OR -LC OPTIONS)
-TR: TAPE & REEL
(SEE SHEET 3, TAPE AND REEL VIEW)
-SN: SOLDER NAIL (USE WT-27-03)
(NOT AVAILABLE WITH -A, -LC, OR
-WT OPTIONS) (SEE FIG. 8 SHEET 3)
BODY SPECIFICATION
-S: SINGLE ROW
(USE TFM-XX-S-XX-XX)
Z
LEAD STYLE
-01: T-1R16-01-X-2
THROUGH HOLE
-02: T-1R16-01-X-2
SURFACE MOUNT
-03: T-1R16-10-X
THROUGH HOLE
*
C
((No. OF POSITIONS x .050[1.27])
+ .125[3.18])REF
((No. OF POSITIONS x .050[1.27])
+ .025[.64])REF
.100 2.54 REF
.065 1.65
01
.050 1.27 REF
2 MAX SWAY
(TYP)
"A"
PLATING SPECIFICATIONS
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-F: 3µ" GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-P: 3µ" GOLD PALLADIUM NICKEL IN CONTACT
AREA, MATTE TIN ON TAIL
-L: 10µ" GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
**
.105 2.67 REF
C
*
NOT RELEASED FOR PRODUCTION
**
NOT TOOLED
.083 2.11
.175 4.45 REF
.018 0.46
2 MAX TOE
(TYP)
"B" REF
.2200 5.588
.1635 4.153 REF
"A"
.014 0.36 REF
((No. OF POSITIONS x .050[1.27])
- .050[1.27])
TABLE 1
ALLOWABLE COPLANARITY
POSITIONS
-02 THRU -29
.004 MAX
-030 THRU -39
.006 MAX
-40 THRU -50
.008 MAX
C
"A"
C
C
.010 0.25 REF
"C"
2 MAX TOE (TYP)
C
2 MAX SWAY (TYP)
Z
(TFM-115-01-X-S-XX SHOWN)
SECTION "A"-"A"
IN-PROCESS
CPC
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
FIGURE 1
FREQUENCY
THIS SHEET
A
C1, C2
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
LEAD STYLE
-01
-02
-03
BODY
TFM-XX-S-XX-XX
TFM-XX-S-XX-XX
TFM-XX-S-XX-XX
TABLE 2
"A"
0.075 [1.91]
N/A
0.109 [2.77]
"B"
0.133 [3.38]
0.133 [3.38]
0.140 [3.56]
"C"
0.4285 [10.884]
0.4285 [10.884]
0.644 [16.36]
B C3, C4, C5,
C6
MATERIAL:
C
D
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0020 [.051]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
INSULATOR: LIQUID CRYSTAL POLYMER, COLOR: BLACK
TERMINAL: PHOSPHOR BRONZE
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.4
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
TFM-1XX-XX-X-S-XX
8/21/2008
SHEET
1
OF
3
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW
BY:
D. SCHMELZ
REVISION Z
SURFACE MOUNT
(TFM-115-02-X-S-XX SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1
FIGURE 2
2 MAX TOE
(TYP)
90°
-K: POLYIMIDE FILM PAD
(TFM-115-02-X-S-K SHOWN)
.021±.010 0.52±0.254
.216±.005 5.49±0.13
FIGURE 3
"B"
+.005
+0.127
0.000
C
.225
- .000
5.70
0
SEE TABLE 1
C
"B"
C
.230 5.83
"R"
NOTE: “R” = OVERALL LENGTH REF
“S” = ((“R” - .216[5.49]) /2) ±.020[.51]
"S"
2 MAX SWAY
(TYP)
02
FLUSH TO .005 0.12 MAX
(SEE NOTE 3)
.185 4.70 REF
7
-A OPTION
(TFM-115-02-X-S-A SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1)
FIGURE 5
03
01
SECTION "B"-"B"
((No. OF POSITIONS x .050[1.27]) -.050[1.27])
(TOL ACCUM ±.005[.13] OVER 50 POS.)
.050 1.27
REF
((No. OF POSITIONS x .050[1.27])
+ .075[1.91])
.045 1.14 REF
R.025 0.64
-WT OPTION
(TFM-115-01-X-S-WT SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1)
FIGURE 4
"M"
C
"P"
((NO OF POSITIONS X .050[1.27])
+.263[6.68]) REF
"D"
TFM-XX-S-01-WT
WT-25-07-T
.050 1.27
"E"
.093 2.36 (TYP)
.010 0.25
REF (TYP)
2 MAX SWAY (TYP)
C
C
-P OPTION
(TFM-115-02-X-S-P SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1)
(PAD TO BE POSITIONED ON C.L. AS SHOWN)
FIGURE 6
.375 9.53
REF
PPP-15
.175 4.45
REF
"D"
.025 0.64
REF
C
L
"E"
SECTION "E"-"E"
NOTE: “M” = (No. OF POSITIONS X .050[1.27]) + .125[3.18] REF
WITH -WT “M” = (No. OF POSITIONS X .050[1.27]) + .263[6.68] REF
“P” = ((“M” - .375[9.53]) /2) ±.020[.51]
PROPRIETARY NOTE
SECTION "D"-"D"
FREQUENCY
THIS SHEET
A
C7, C8, C9,
B C10, C11,
C12
C
D
((No. OF POSITIONS x .050[1.27])
+ .154[3.91])
CPC
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
TFM-1XX-XX-X-S-XX
8/21/2008
SHEET
2
OF
3
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW
BY:
D. SCHMELZ
REVISION Z
TAPE AND REEL VIEW
POSITION 01
PT-1-24-11-09
**
-SN OPTION
(TFM-110-02-X-S-SN SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1)
(No OF POSITIONS x .050[1.27]) + .255 REF
"G"
FLUSH TO .005 0.13
ABOVE
FIGURE 8
"F"
"F"
USER DIRECTION OF UN-REELING
POCKET NOT DETAILED
WT-27-03-X
"G"
PACKAGING TUBE VIEW
NOTES:
(No. OF POSITIONS x .050[1.27])
+.175[4.45]
2 MAX SWAY (TYP)
.075 1.91
REF
.026 0.66 REF
(2 PLCS)
Z
SECTION "F"-"F"
SCALE 1.25 : 1
1. USE PT-1-24-11-09 TUBE
AND (2) TP-24 FOR -A, -LC, WT,
AND -SN OPTIONS.
2. USE PT-1-24-03-09 TUBE AND
(2) TP-09 FOR -P AND -K OPTIONS.
3. LOAD TUBE WITH 1ST POSITION
IN SAME DIRECTION AS ARROW
SECTION "G"-"G"
SCALE 3 : 1
**
NOT TOOLED
FIGURE 7
-LC OPTION
(TFM-115-01-X-S-LC SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 2)
TFM-1XX-02-S-LC
C
L
C
.050 1.27
LC-05-TM
.056 1.42 REF
*
*
*
* INSPECT ONLY WHEN APPLICABLE WITH RESPECT TO ASSEMBLY OPTION
FREQUENCY
THIS SHEET
A
B
C
D
C13
2 MAX SWAY (TYP)
.010 0.25 REF
2 MAX SWAY (TYP)
CPC
((No. OF POSITIONS x .050[1.27])
+ .075[1.91])±.002[.05]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
DWG. NO.
TFM-1XX-XX-X-S-XX
8/21/2008
SHEET
3
OF
3
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW
BY:
D. SCHMELZ
Robotics Development
京公网安备 11010802033920号
EEWORLD
