The UT54ACS85 and the UT54ACTS85 are 4-bit magnitude
comparators that perform comparison of straight binary and
straight BCD (8-4-2-1) codes. Three fully decoded decisions
about two 4-bit words (A, B) are made and are externally avail-
able at three outputs. Devices are fully expandable to any num-
ber of bits without external gates. The cascading paths of the
devices are implemented with only a two-gate-level delay to
reduce overall comparison times for long words. An alternate
method of cascading which further reduces the comparison time
is shown in the typical application data.
The devices are characterized over full military temperature
range of -55 C to +125 C.
LOGIC SYMBOL
A0
A1
A2
A3
(A<B)IN
(A=B)IN
(A>B)IN
B0
B1
B2
B3
(10)
(12)
(13)
(15)
(2)
(3)
(4)
(9)
(11)
(14)
(1)
3
<
=
>
0
B
A
<
=
>
(7)
(6)
(5)
(A<B)OUT
(A=B)OUT
(A>B)OUT
COMP
0
3
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and IEC
Publication 617-12.
PINOUTS
16-Pin DIP
Top View
B3
(A<B)IN
(A=B)IN
(A>B)IN
(A>B)OUT
(A=B)OUT
(A<B)OUT
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
A3
B2
A2
A1
B1
A0
B0
16-Lead Flatpack
Top View
B3
(A<B)IN
(A=B)IN
(A>B)IN
(A>B)OUT
(A=B)OUT
(A<B)OUT
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
A3
B2
A2
A1
B1
A0
B0
51
RadHard MSI Logic
UT54ACS85/UT54ACTS85
FUNCTION TABLE
COMPARING INPUTS
A3, B3
A3>B3
A3<B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A3=B3
A2, B2
X
X
A2>B2
A2<B2
A2=B2
A2=B2
A2=B2
A2=B2
A2=B2
A2=B2
A2=B2
A2=B2
A2=B2
A1, B1
X
X
X
X
A1>B1
A1<B1
A1=B1
A1=B1
A1=B1
A1=B1
A1=B1
A1=B1
A1=B1
A0, B0
X
X
X
X
X
X
A0>B0
A0<B0
A0=B0
A0=B0
A0=B0
A0=B0
A0=B0
CASCADING INPUTS
A>B
X
X
X
X
X
X
X
X
H
L
X
H
L
A<B
X
X
X
X
X
X
X
X
L
H
X
H
L
A=B
X
X
X
X
X
X
X
X
L
L
H
L
L
A>B
H
L
H
L
H
L
H
L
H
L
L
L
H
OUTPUTS
A<B
L
H
L
H
L
H
L
H
L
H
L
L
H
A=B
L
L
L
L
L
L
L
L
L
L
H
L
L
LOGIC DIAGRAM
(15)
A3 (1)
B3
(5)
A>B
A2 (13)
B2 (14)
A<B (2)
(3)
A=B
(4)
A>B
(6)
A=B
(12)
A1
B1 (11)
(7)
A<B
(10)
A0
(9)
B0
RadHard MSI Logic
52
UT54ACS85/UT54ACTS85
RADIATION HARDNESS SPECIFICATIONS
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
JC
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
10
1
UNITS
V
V
C
C
C
C/W
mA
W
I
I
P
D
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
C
53
RadHard MSI Logic
UT54ACS85/UT54ACTS85
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V 10%; V
SS
= 0V
6
, -55 C < T
C
< +125 C)
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
I
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100 A
I
OH
= -8.0mA
I
OH
= -100 A
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
= 1MHz @ 0V
= 1MHz @ 0V
15
15
pF
pF
2.3
10
1.6
mW/
MHz
A
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
0.40
0.25
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
A
V
V
OH
V
I
OS
I
OL
mA
mA
RadHard MSI Logic
54
UT54ACS85/UT54ACTS85
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%,
- 50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but
are guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density 5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed
3,765 pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at frequency of 1MHz and a signal amplitude of 50mV rms maximum
7. All specifications valid for radiation dose 1E6 rads(Si).
6. Maximum allowable relative shift equals 50mV.
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
Live broadcast time: October 22, 10:00-11:30Live broadcast topic: Gigabit digital isolators for video, converters, and communicationsSpeech document: Click here to downloadWatch replay: Click to watch...
I am a beginner of STM8 and I use IAR. I wrote a short program. In the main loop, LED1 flashes, and in the timer interrupt, LED2 flashes. It runs normally when debugged with STLINK. Then I compiled it...
[img]file:///C:\Documents and Settings\Administrator\Application Data\Tencent\Users\386130771\QQ\WinTemp\RichOle\WF`LQPZ0CY6JCU_8LUG]DUU.jpg[/img][img]file:// /C:\Documents and Settings\Administrator\...
When using the LM6029A 128*64 LCD module, the reset signal of the LCD is provided by the reset circuit, and the controller is S6B0724A01. The LCD is always unsuccessful when it is powered on for the f...
I just read a blog post titled “The Evolution of Universal Oscilloscopes” ( https://home.eeworld.com.cn/my/space.php?uid=169593do=blogid=38945 ) and realized that I’m not the only old-fashioned person...
After a busy day, I suddenly looked up at night and saw the moon in the sky. I thought it was so beautiful. So I used my not-so-sophisticated photography skills to record it, hoping to bring my most s...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
The serial interface real-time clock chip DS1302 launched by Dallas Company in the United States can trickle charge the backup battery of the clock chip. Due to the main features of the chip such a...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]
Car lights, whether headlights, fog lights or tail lights, play an important role in driving safety. However, the material of the car lights determines that the probability of damage in a collision...[Details]
At present, with the diversification of portable products and the almost harsh requirements for audio and video parts, the power consumption requirements of the whole machine have been raised to a ...[Details]
It should be understood as follows: DC-DC means direct current to direct current (conversion of different DC power values). Anything that meets this definition can be called a DC-DC converter, incl...[Details]
Fairchild's FAN6208 is a synchronous rectification (SR) controller for isolated LLC or LC resonant converters that can drive two individual SR MOSFETs emulating the behavior of rectifier diodes. FAN62...[Details]
TMC428 is a stepper motor motion controller from TRINAMIC. It can reduce the workload of motor control software design and development costs. The 3-axis stepper motor drive control system based on ...[Details]
New Automobile
Hydraulic Clutch
The hydraulic control system uses almost 100% advanced engineering plastics, which overcomes the shortcomings of the main and branch cylinders of metal clutc...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
