1. The SRAM is immune to latchup to particles >111MeV-cm
2
/mg.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum and default EDAC scrub rate.
SUPPLY SEQUENCING
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
POWER-UP REQUIREMENTS
During power-up of the UT8ER512K32 device, the power
supply voltages will transverse through voltage ranges where
the device is not guaranteed to operate before reaching final
levels. Since some circuits on the device will start to operate at
lower voltage levels than others, the device may power-up in an
unknown state. To eliminate this with most power-up situations,
the device employs an on-chip power-on-reset (POR) circuit.
The POR, however, requires time to complete the operation.
Therefore, it is recommended that all device activity be delayed
by a minimum of 100ms, after both V
DD1
and V
DD2
supplies
have reached their respective minimum operating voltage.
4
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D2
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage (Core)
DC supply voltage (I/O)
Voltage on any pin
Storage temperature
Maximum package power dissipation
permitted @ Tc = +125
o
C
Maximum junction temperature
Thermal resistance, junction-to-case
2
DC input current
LIMITS
-0.3 to 2.1V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
5W
+150°C
5°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Per MIL-STD-883, Method 1012, Section 3.4.1, P
D
= (T
JC
(max) - Tc (max))
Θ
JC
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
V
IN
PARAMETER
DC supply voltage (Core)
DC supply voltage (I/O)
Case temperature range
DC input voltage
LIMITS
1.7 to 1.9V
1
3.0 to 3.6V
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
Notes:
1. For increased noise immunity, supply voltage V
DD1
can be increased to 2.0V. All characteristics contained herein are guaranteed by characterization at V
"The wind is whistling, the horses are neighing!" Although I don't have to face other people's cold faces because of my low technology in recent years. But the fierce winds and waves in the world also...
I have just come into contact with Wince 6.0. Now I want to implement a function that uses a url link to download. I refer to some programs on the Internet and write the following code [code] void CHt...
I would like to ask what is the use of the EVC4-TOOL-WINDOWS CE PLATFORM MANAGER CONFIGURATION option? How can I add an item to this option (the one with a + sign in front)? I am a newbie and I have s...
When I transplanted a project from ADS1.2 to Keil3 IDE, after solving some compilation errors and referring to some instructions, there were no errors after the compilation was completed. Of course, t...
The register configuration has been configured. I just started learning microcontrollers and just came into contact with PWM. Now the register configuration is done, but how can the LED turn on and of...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Introduction
X1226 has the functions of clock and calendar. The clock relies on hour, minute and second registers to track, and the calendar relies on date, week, month and year registers to tr...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
In order to develop lighting LED technology, developed countries attach great importance to the research of LED testing methods and standards. For example, the National Institute of Standards and T...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
