12.2003
LCD MODULE 1x8 - 11.48mm
INCL. CONTROLLER HD 44780
Issue 04.2011
g
tin
oun
m
ore uired
m
no
req
Dimension 68 x 27 mm
11mm flat even with LED B/L
FEATURES
HIGH CONTRAST LCD SUPERTWIST DISPLAY GRAY OR YELLOW/GREEN
COMPATIBLE TO HD 44780 STANDARD
INTERFACE FOR 4- AND 8-BIT DATA BUS
POWER SUPPLY
+2.7~5.5V
(BACKLIGHT 4.1V)
OPERATING TEMPERATURE RANGE 0~+50°C OR -20~+70°C
BULIT-IN TEMP. COMP. WITH EA DIP081-CHNLED
LED BACKLIGHT Y/G typ. 150mA@4.1V, max. 200mA
SOME MORE MODULES WITH SAME MECHANIC AND SAME PINOUT:
- DOTMATRIX 2x16, 4x20
- GRAPHIC 122x32
*
NO SCREWS REQUIRED: SOLDER ON IN PCB ONLY
*
DETACHABLE VIA 9-PIN SOCKET EA B200-9 (2 PCS. REQUIRED)
*
*
*
*
*
*
*
*
ORDERING INFORMATION
LCD MODULE 1x8 - 11.48mm WITH BACKLIGHT Y/G
SAME BUT WITH T
OP.
-20~+70°C, INCL. TEMP.COMP.
9-PIN SOCKET, HEIGHT 4.3mm (1 PC.)
SUITABLE BEZEL (WINDOW 60.0x14.8 mm)
ADAPTOR PCB WITH STANDARD PINOUT PITCH 2.54mm
EA
EA
EA
EA
EA
DIP081-CNLED
DIP081-CHNLED
B200-9
017-2UKE
9907-DIP
Zeppelinstr. 19 · D-82205 Gilching · Tel. 08105-77 80 90 · Fax 08105-77 80 99 · www.lcd-module.de · info@lcd-module.de
EA DIP081-CNLED
Page 2
ELECTRONIC ASSEMBLY reserves
the right to change specifications
without prior notice. Printing and
typographical errors reserved.
PINOUT
Pin Symbol Level Function
1
2
3
4
5
6
7
8
9
VSS
VDD
VEE
RS
R/W
E
D0
D1
D2
L
H
-
H/L
H/L
H
H/L
H/L
H/L
Power Supply 0V (GND)
Power Supply +5V
Contrast adjust. (about 0V)
H=Command, L=Data
H=Read, L=Write
Enable (falling edge)
Display Data, LSB
Display Data
Display Data
Pin
10
11
12
13
14
15
16
17
18
Symbol Level Function
D3
D4 (D0)
D5 (D1)
D6 (D2)
D7 (D3)
-
-
A
C
H/L
H/L
H/L
H/L
H/L
-
-
-
-
Display Data
Display Data
Display Data
Display Data
Display Data, MSB
NC (see EA DIP122-5N)
NC (see EA DIP122-5N)
LED B/L+ Resistor required
LED B/L -
5V operation
3.3V operation
+3,3V
22k
W
CONTRAST ADJUSTMENT
VEE
10k
W
Both displays EA DIP081-CNLED and -CHNLED do have an driving voltage for
3,6k
W
contrast of typ. 4,9V. For 3.3V operation additional -3.3V is required.
-3,3V
Version EA DIP081-CHNLED for ext. temperature range -20..+70°C does have a built-
in temperature compensation; so there's no need for contrast adjustment while operation.
BACKLIGHT
Backlight do need an external resistor limiting the current limitor. Calculation is: R=U/I, so at 5V supply:
R
gelb/grün
=(5,0V-4,1V)/0,15A= 6 Ohm
Caution: do never drive backlight direct with 5V; damage may come suddenly.
CHARACTER SET
Character set shown below is already built in. In addition to that you are able to define up to 8 characters
by yoursself.
ELECTRONIC ASSEMBLY reserves
the right to change specifications
without prior notice. Printing and
typographical errors reserved.
EA DIP081-CNLED
Page 3
TABLE OF COMMAND
Code
Instruction
Clear Display
DB DB DB DB DB DB DB DB
RS
R/W
7
6
5
4
3
2
1
0
Description
Clears all display and returns the cursor
Execute
Time
(max.)
1.64ms
0
0
0
0
0
0
0
0
0
1
to the home position (Address 0).
Cursor At Home
0
0
0
0
0
0
0
0
1
Returns the Cursor to the home position
(Address 0). Also returns the display
*
being shifted to the original position. DD
RAM contents remain unchanged.
Sets the Cursor move direction and
specifies or not to shift the display.
S
These operation are performed during
data write and read.
Sets ON/OFF of all display (D) cursor
B
ON/OFF (C), and blink of cursor position
character (B).
1.64ms
Entry Mode Set
0
0
0
0
0
0
0
1 I/D
40µs
Display On/Off
Control
Cursor / Display
Shift
Function Set
CG RAM Address
Set
DD RAM Address
Set
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
D
C
40µs
40µs
40µs
1
S/C R/L
*
F
*
*
without changing DD RAM contents.
Moves the Cursor and shifts the display
Sets interface data length (DL) number
1 DL N
*
of display lines (L) and character font
(F).
Sets the CG RAM address. CG RAM
data is sent and received after this
setting.
Sets the DD RAM address. DD RAM
data is sent and received after this
setting.
Reads Busy flag (BF) indicating internal
operation is being performed and reads
address counter contents.
Writes data into DD RAM or CG RAM
Reads data from DD RAM or CG RAM
0
0
0
1
ACG
40µs
0
0
1
ADD
40µs
Busy Flag / Address
0
Read
CG RAM / DD RAM
Data write
CG RAM / DD RAM
Data Read
1
1
1 BF
0
1
AC
Write Data
Read Data
-
40µs
40µs
INITIALISISATION FOR A 1 LINE DISPLAY / 8-BIT MODE
Command
Function Set
Display ON/OFF
Clear Display
Entry Mode Set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
Remark
8 bit data length, 1 line display, 5x7 font
display on, cursor on, cursor blink
clear display, cursor 1st. row, 1st. column
cursor increments automatically
CREATING YOUR OWN CHARACTERS
All these character display modules got the feature to create 8 own characters (ASCII Codes 0..7) in
addition to the 192 ROM fixed codes.
Set CG RAM Address
Data
1.) The command "CG RAM Address Set"
Bit
Adresse
Hex
Hex
defines the ASCII code (Bit 3,4,5) and the
7 6 5 4 3 2 1 0
dot line (Bit 0,1,2) of the new character.
0 0 0 $40
0 0 1 0 0 $04
Example demonstrates creating ASCII
0 0 1 $41
0 0 1 0 0 $04
0 1 0 $42
0 0 1 0 0 $04
code $00.
0 0 1 0 0 $04
2.) Doing 8 times the write command "Data
0 1 0 0 0 0 1 1 $43
X X X
1 0 0 $44
1 0 1 0 1 $15
Write" defines line by line the new
1 0 1 $45
0 1 1 1 0 $0E
character. 8th. byte stands for the cursor
1 1 0 $46
0 0 1 0 0 $04
line.
1 1 1 $47
0 0 0 0 0 $00
3.) The new defined character can be used as
a "normal" ASCII code (0..7); use with "DD RAM Address Set" and "Data Write".
Power technology
京公网安备 11010802033920号
EEWORLD
