EEWORLDEEWORLDEEWORLD

Part Number

Search

SK400M47A1FQ1632

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 47uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size61KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SK400M47A1FQ1632 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 47uF, Through Hole Mount, ROHS COMPLIANT

SK400M47A1FQ1632 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance47 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.401 mA
Manufacturer's serial numberSG
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)400 V
ripple current300 mA
surface mountNO
Delta tangent0.24
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SG
[ Electronic Ballast ]
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40 ~ +105°C / -25 ~ +105°C
Working Voltage : 160 ~ 400V / 450V
Rate Capacitance Range : 4.7 ~ 330µF / 3.3~100µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.02 CV + 25
( After 2 Minute Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 160
200
250
350
400
450
D.F (%) : 15
15
15
20
24
24
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Load Life : 5000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Miniature Size Aluminum
Electrolytic Capacitors
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
50,60
0.80
120
1.00
300
1.20
1K 10K~100K
1.40
1.6
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.5
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
Four-quadrant stepper motor control simulation with interpolation calculation and single-chip microcomputer source program
[color=#252525][size=14px]51 MCU uses ULN2003A chip to drive stepper motor program plus Proteus simulation [/size][/color] [color=#252525][size=14px]The MCU source program is as follows: [/size][/colo...
Jacktang Microcontroller MCU
About the errors of EZDSP2808 and 28335 (be careful when referring to them)
The power-up sequence of 2808 and 28335 is completely opposite to that of 2812. However, the power-up sequence of EZDSP2808 and 28335 is the same as that of 2812, which may cause: output buffers to tu...
hlx3012 Microcontroller MCU
Very useful! The voltage, current and temperature safety zones of 13 types of components in switching power supplies!
[color=rgb(50, 50, 50)][font=myFont, "][size=14px]Overview[/size][/font][/color][color=#323232][font=myFont, "][size=14px] Why should components be used at derating? Because if the working state of th...
木犯001号 Power technology
It's time to change! Awesome change, the latest design to replace RS-485 optocoupler isolation
[i=s] This post was last edited by Jacktang on 2019-4-12 09:05 [/i] [size=4] Friends who have worked on RS-485 optocoupler isolation circuits must have been annoyed for a long time. This commonly used...
Jacktang Analogue and Mixed Signal
What is the distance between the two lines of DDR differential clock?
What is the spacing between the two DDR differential clock lines? If I wind a serpentine line, do I need to wind two lines together everywhere?...
xujiangyu0619 PCB Design
FPGA overlay technology redefines: 2.5D to the left and 3D to the right
Author: Zhao Sixiao Source: EEWOLRD"The dream product has already started shipping," said Mr. Liren Tang, Xilinx's senior vice president and executive president of Asia Pacific, at the press conferenc...
思潇 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2729  992  2190  2391  1906  55  20  45  49  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号