FPV321611G120PLB datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> FPV321611G120PLB

FPV321611G120PLB: DescriptionVaristor, 12V, 0.1J, Surface Mount, CHIP, 1206; CategoryPassive components The resistor; File Size1MB，15 Pages; ManufacturerFenghua (HK) Electronics Ltd.; Environmental Compliance

Download Datasheet Parametric View All

FPV321611G120PLB Overview

Varistor, 12V, 0.1J, Surface Mount, CHIP, 1206

FPV321611G120PLB Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Fenghua (HK) Electronics Ltd.
package instruction	CHIP, 1206
Reach Compliance Code	unknown
Circuit maximum DC voltage	12 V
Circuit RMS maximum voltage	8.5 V
Maximum energy absorption capacity	0.1 J
JESD-609 code	e4
Manufacturer's serial number	FPV
Installation features	SURFACE MOUNT
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	RECTANGULAR PACKAGE
method of packing	BULK
Resistor type	VARISTOR
surface mount	YES
Terminal surface	Silver/Palladium/Platinum (Ag/Pd/Pt)
Terminal location	DUAL ENDED
Terminal shape	WRAPAROUND

Preview

Download Datasheet

View All

GUANGDONG ZHAOQING YINGDA INDUCTOR CO。

，LTD

SMD COMPONENTS

Introduction fo FPV Series Multilayer

Chip Varistor

Multilayer Chip Varistors (MLV) are Transient Voltage Suppressors (TVS) which manufactured

from semiconducting ceramics by the highly advanced multilayer formation technologies, which can

offer rugged protection, excellent transient energy absorption and internal heat dissipation. The

devices are leadless chip form, eliminating lead inductance and guaranteeing a faster speed of

response time of less than 0.5ns, which makes them fast enough to ensure reliable protection against

ESD pulse and other specific transient events. These transient suppression devices are significantly

smaller footprints and lower profiles than traditional zener diodes or radial MOVs.

Section of the chip

Features　

Multilayer Ceramic Construction Technology

Leadless 1005[0402], 1608[0603], 2012[0805], 3216[1206], 3225[1210], 4532[1812],

8063[3225] and 1080[4032] Chip Size

-55º to +125º Operating Temperature Range

Operating Voltage Range Vw(DC) =3.3V to 615V

Inherent Bi-directional Clamping

Suitable for ESD Protection

Very Low Leakage Current

Low Inductance, Fast Response (Response time<0.5ns)

Excellent Temperature Coefficient

Good Solderability (The electrode termination is selectable in plated and silver

/palladium/platinum.)

Information for Designer　

Voltage Dependent Characteristic

Transient Voltage Suppressors (Varistors) are voltage-dependent electrical resistors with symmetrical

V/I characteristic. Their resistance value decrease with increasing voltage, thus

“

short-circuiting”further rises in overvoltage.

GUANGDONG ZHAOQING YINGDA INDUCTOR CO。

，LTD

SMD COMPONENTS

Terms and Descriptions　

Working DC Voltage (Vw(DC))

This is the maximum continuous DC voltage, which may be applied up to the maximum operating

temperature of the device. The rated DC operating voltage (working voltage) is also used as the

reference point for leakage current. This voltage is always less than the breakdown voltage of the

device.

Working AC Voltage (Vw(AC))

This is the maximum continuous sinusoidal rms voltage, which maybe applied at any temperature up

to the maximum operating temperature of the device.

Maximum Surge Current (Peak Current I

)

This is the maximum peak current, which may be applied for an 8/20µs impulse, with rated line

voltage also applied, without causing device failure. The pulse can be applied to the device in either

polarity with the same confidence factor.

Maximum Surge Energy (Es)

This is the maximum rated transient energy which may be dissipated for a single current pulse at a

specified impulse duration (10/1000µs), with the rated DC or RMS voltage applied, without causing

device failure.

leakage (I

) at Rated DC Voltage

In the no conducting mode, the device is at a very high impedance (approaching 10

ohms) and

appears as an almost open circuit in the system. The leakage current drawn at this level is very low

(<50µA at ambient temperature) and, unlike the zener diode, the multilayer varistors have the added

advantage that, when operated up to its maximum temperature, its leakage current will not increase

above 500µA.

Varistor Voltage (V

(DC))

This is the voltage at which the device changes from the off state to the on state and enters its

conduction mode of operation. The voltage is usually characterized at the 1mA point.

Clamping Voltage (Vc)

This is the peak voltage appearing across the suppressor when measured at conditions of specified

pulse current and specified waveform (8/20µs). It is important to note that the peak current and peak

voltage may not necessarily be coincidental in time.

Capacitance (Cp)

This is the capacitance of the device at a specified frequency 1MHz and bias 0.5V

Application　

The Prevention of Overvoltage

When the voltage increases above the threshold of MLV, the suppressor will draws a rapidly

increasing current, and then the overvoltage is considerably attenuated away from the protection of

the equipments should be supplemented by including specific components that will raise the withstand

capabilities to the required level. Varistors provide protection against all kind of overvoltage and

prevent electronic equipment from being damaged by transient events.

Recommended Resources

Technical information about gravity sensors

Dual voltage rectifier circuit

Telephone ring control relay circuit diagram

Shuangying brand fully automatic soybean milk machine circuit diagram

Tunnel diode monostable circuit

820e computer motherboard circuit diagram_72

Altium Designer: Remove the restriction that multiple people cannot be allowed in a LAN: Altium Designer: Remove the restriction that multiple people cannot share a license at the same time in a LAN. I wonder if anyone wants Altium Designer 8.0 (winter 09). Remove the restriction that mul...; qwqwqw2088 PCB Design

The difference between debug mode and offline mode in CCS: I have an SPI program. In the debug mode of CCS, both free and step are normal without any problems. However, when downloaded to MSP430 and run offline, the timing of the entire SPI is much tighter th...; sptt1 Microcontroller MCU

No one has a wireless ad hoc network solution, we are in urgent need of: There are about 100 nodes, which can be clustered. The amount of data is not large, just location information plus status information, similar to wireless sensor networks, but with voice functions. It...; dongzhi1128 RF/Wirelessly

cc3200 arrives in Shenzhen and requires proof for customs clearance, how to solve it: This is the first time I've encountered something like this. Is this true? I don't know what to do :Cry:...; 小打小闹赢大奖 TI Technology Forum

18B20+1302 LCD1602 display: I fixed 1302 some time ago and also brought 18B20 with me. The underlying driver is quite troublesome, mainly because the delay is not very accurate. I did not adjust the leap year part, which means t...; kobe1941 MCU

There is a dinner party in Shenzhen, come quickly! Around 7pm on August 24th, anyone?: I'm going to Shenzhen to attend a meeting on August 24th, so I want to invite friends in Shenzhen to have a small gathering and find something delicious to eat. Let's start eating around 7pm on August...; soso Talking

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components