EEWORLDEEWORLDEEWORLD

Part Number

Search

CLM-116-02-L-D-K-PA-TR

Description
Board Connector, 32 Contact(s), 2 Row(s), Female, Straight, 0.039 inch Pitch, Surface Mount Terminal, Black Insulator, Plug
CategoryThe connector    The connector   
File Size191KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Download Datasheet Parametric View All

CLM-116-02-L-D-K-PA-TR Overview

Board Connector, 32 Contact(s), 2 Row(s), Female, Straight, 0.039 inch Pitch, Surface Mount Terminal, Black Insulator, Plug

CLM-116-02-L-D-K-PA-TR Parametric

Parameter NameAttribute value
MakerSAMTEC
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPICK&PLACE PAD, TAPE&REEL PKG
Board mount optionsPOSITIONING PIN
body width0.1 inch
subject depth0.084 inch
body length0.647 inch
Body/casing typePLUG
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance15 mΩ
Contact styleSQ PIN-SKT
Durability100 Cycles
maximum insertion force.417 N
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial numberCLM
Plug contact pitch0.039 inch
Match contact row spacing0.039 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing3.175 mm
Plating thickness10u inch
Rated current (signal)1.5 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length
Terminal pitch0.9906 mm
Termination typeSURFACE MOUNT
Total number of contacts32
Evacuation force-minimum value.2085 N
MSP430 power consumption issues
MSP430G2231, I output a 38KHZ square wave signal with a duty cycle of 1/3, but the power consumption is still nearly 2 MA. Why is the power consumption still so high? Please give me some advice. TACCR...
yyhhgg Microcontroller MCU
Why does the output voltage of an op amp need to be offset? Analysis of the principle of differential circuit
The differential operational amplifier circuit effectively suppresses the common-mode signal and only amplifies the differential signal, so it is widely used.Circuit Configuration of Differential Circ...
infinigo Integrated technical exchanges
[Mill MYC-J1028X development board trial] Use Node-RED to transform the MYC-J1028X development board into an industrial control gateway
[i=s]This post was last edited by HonestQiao on 2022-10-2 10:59[/i]This article is long and involves many knowledge points. You need to read it patiently. The following is the directory of specific co...
HonestQiao NXP MCU
How to transfer Q, I, and M registers to V register in PLC program?
[size=3]Please give me some advice on how to transfer Q, I, M registers to V register in PLC program[/size]...
eeleader Industrial Control Electronics
CCS3.3 Chinese Learning Manual
I have uploaded two Chinese learning manuals for CCS3.3, I hope they will be helpful to everyone!...
kooking DSP and ARM Processors
Programs written in EVC cannot open the GPIO driver when operated under wince5.0
I used evc to write a gpio output program, but when I opened the driver with wince system, it showed that the gpio driver failed to be opened. I don't know why. I used the s3c2440 experimental board o...
gaoli.85 Embedded System

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1794  1441  1135  1411  2647  37  30  23  29  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号