EEWORLDEEWORLDEEWORLD

Part Number

Search

OC086P3D27-100M

Description
PECL Output Clock Oscillator, 100MHz Nom
CategoryPassive components    oscillator   
File Size40KB,1 Pages
ManufacturerPletronics
Download Datasheet Parametric View All

OC086P3D27-100M Overview

PECL Output Clock Oscillator, 100MHz Nom

OC086P3D27-100M Parametric

Parameter NameAttribute value
MakerPletronics
Reach Compliance Codeunknown
Frequency Adjustment - MechanicalNO
frequency stability0.2%
Frequency Stability - Voltage0.01 ppm
input power2 W
Manufacturer's serial numberOC086
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency100 MHz
Maximum operating temperature70 °C
Minimum operating temperature-20 °C
Oscillator typePECL
Oven power supply voltage3.3V
physical size26.16mm x 26.16mm x 12.57mm
Nominal supply voltage3.3 V
surface mountNO
Preheating power5.5 W
Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
OC086 OCXO Series
1.0"x1.0" Nominal Thru-Hole Oven Controlled Xtal Oscillator
Electronic Adjustment
Standard Specifications
Operating Temperature Range
vs. Temp
Overall Frequency
vs. Vdc / Load
Stability
Aging
Frequency Adj
Supply Voltage (Vdc)
Supply Current (Icc)
Phase Noise
Jitter
Oven Monitor
Output Logic
Output Voltage Levels
Output Load (Test Circuit TBD)
0 to +50°C to -30 to +70°C available
± 1 x 10
-8
over Operating Temperature Range available
± 1 x 10 -
8
for ± 5% load or supply change
± 1 PPM max. for 10 years at 25°C ± 5°C at 10 MHz (Consult factory for other frequencies)
Electrical: ± 1 PPM typical
+3.3 to +12 Vdc available
2.0 Watts typical steady state, 5.5 Watts maximum at turn-on
Consult Factory
Consult Factory
Consult Factory
HCMOS
Logic “1” 90% of Vcc min
Logic “0” 10% of Vcc max
10 TTL Loads or 15pF
Sine Wave
0 to +7 dBm
50 ohms
PECL
Consult Factory
TTL
Consult Factory
10.00 MHz
100.00 MHz
Part Numbering Guide
Consult factory for
available frequencies
and specs. Not all
options available
for all frequencies.
A special p/n may
be assigned.
Frequency Stability
is inclusive of
frequency shifts due
to calibration,
temperature, supply
voltage, shock,
vibration and load
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
OC086 H 3 A 27 - 100.0M - XXX
(Internal Code or blank)
Model Series
Logic
H: HCMOS
S: Sine Wave
P: PECL
T: TTL
Supply Voltage
3: +3.3 Vdc
5: +5.0 Vdc
12: +12.0 Vdc
not to scale
Frequency in MHz
Standard Frequencies: 10, 13, 80 & 100 MHz
Frequency Stability
27 =
±2
x 10
-7
79 =
±7
x 10
-9
17 =
±1
x 10
-7
18 =
±1
x 10
-8
Operating Temperature Range
A: 0 to +50
°
C
D: -20 to +70
°
C
B: 0 to +70
°
C
E: -30 to +70
°
C
C: -10 to +70
°
C
Mechanical: inches (mm)
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
.75 (19.05)
.495 (12.57)
MAX
1.03 (26.16) MAX
1.03 (26.16) MAX
.50 (12.7)
.25
±
.02
(6.35)
.375 (9.52)
.25 (6.35)
PLETRONICS
OC086
XXXXXX
FREQUENCY
DATE CODE
.125 (3.18)
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
OUT
RF / CASE GND
Vcontrol
N.C.
+Vdc
.125 (3.18)
Lead .03
±
.003
Dia (.76) 5X
.025
±
.010 (.64) x .07 Dia
Insulated riser 4X
3
2
1
.50 (12.7)
.25 (6.35)
.75 (19.05)
4
5
Aug 6, 2003
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
TBD
Conversion between sequence diagram and state machine
Brother Mengyi, I would like to ask how to convert the timing diagram into a state machine. I find that I can understand the timing diagram, but I am not very good at converting it into a state machin...
yz890627 FPGA/CPLD
Is the crystal oscillator important in the STM32 system?
I built a minimal STM system myself, with just a chip and wires, and tried it. It was not unstable. I don't know if it can be used normally except that the multiplication frequency is a little low and...
jisuf stm32/stm8
uCOS-II V2.86 migration based on LM3S9B96
Single task: blinking LED;LED/IO: PF3;Directly onto the program: Mainly based on the LM3S9B92 based uCOSII V2.86 porting, hope it will be helpful to beginners!...
xylq0826 Microcontroller MCU
Using ir2110 driver to make a buck circuit
I want to make a BUCK circuit, I am new to switching power supply. I designed a circuit diagram, can you help me see if it is feasible? I haven't configured the parameters yet. Mainly, is it okay to u...
光芒。 Switching Power Supply Study Group
Methods for solving faults in FPGA design and development based on EDA simulation technology.pdf
Methods for solving faults in FPGA design and development based on EDA simulation technology.pdf...
zxopenljx FPGA/CPLD
STM32 smart card issue
In STM32's serial smart card mode, how should it be connected? The manual says that TX and SW_RX should be connected together, so which pin is SW_RX?...
使者0123 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 313  2651  499  1630  1984  7  54  11  33  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号