[color=black][font=Verdana]It should be understood as follows: DC-DC means DC to DC (conversion of different DC power values). Anything that meets this definition can be called a DC-DC converter, incl...
The CH579M-R1 development board is not equipped with W25Q16 memory. To add this storage function, you can connect it externally.
In terms of software, the resources of the CH579 EVT development board ...
There are three ways to reduce the heat accumulation of LEDs. The first is to improve the luminous efficiency. During the chip manufacturing stage, the energy configuration of 20% luminescence and 80%...
[align=left][font=宋体][size=11.0pt]This short animation introduces and demonstrates how to set up the TI[/size][font=宋体][size=11.0pt]ADS8353[/size][font=宋体][size=11.0pt]performance demonstration kit. T...
Reprinted How to Learn Microcontrollers Well - Guo Tianxiang. If there is any infringement, please delete it by the administrator. I also want to provide good information for students who want to lear...
The router can only be used as a HUB now. My roommate had a problem after using a P network law enforcement officer. The router showed that it was connected to the Internet, but the number of received...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
