T1, T2, Actuator shown with B2 bushing, subtract 0.09 (2.29) for B5 bushing, subtract 0.04 (1.02) for B5 bushing, add 0.09 (2.29)
Std for M2 terminal sub 0.016 (0.04) for M2 terminals sub. 016 (0.04) for M6.
Bushing Options
B2 NON-THD
B5 THD
Termination Options
M2
Double Pole
M6, SPDT
SPDT
P. C. Mounting
www.element14.com
www.farnell.com
www.newark.com
Page <3>
06/06/11 V1.1
Toggle Switches
Sub-Miniature
M6, DPDT
DPDT
P. C. Mounting
Panel Mounting
10-48 Bushing
1/4 In. Bushing
Without Locking Ring
Without Std. Locking Ring
Without Locking Ring
Without Std. Locking Ring
Hardware
Locking Ring
www.element14.com
www.farnell.com
www.newark.com
Page <4>
06/06/11 V1.1
Toggle Switches
Sub-Miniature
Contact Material Options
Contact Plating
R
Gold
Terminal Plating
R = Gold
Ratings
0.4 Volt - Amperes (VA) maximum at 20 V maximum (AC or DC)
Soldering Process:
Manual soldering
Wave soldering
: Use soldering iron of 30 watts, controlled at 350°C approximately 5 s while applying solder.
: Recommended soldering temperature : 260 ±5°C.
: Duration of solder immersion
: Maximum 5 s (PCB is 1.6 mm in thickness).
Soldering : Vapour phase
Important Notice :
This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of
it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces
all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use
made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted.
Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising)
[i=s] This post was last posted by colordancer on 2014-10-7 23:44 Edit [/i] I've been learning about hardware development recently, so I've used the JAWBONE UP wristband to practice. Now I've got the ...
I am a student at school, and I have just come into contact with microcontrollers and gprs. I would like to ask the experts for advice. The project I am currently working on is an ECG data transmissio...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Xiaomi, a well-known Internet phone in mainland China, won a million-unit order contract from China Unicom on November 20 last year, which made Xiaomi famous in mainland China. In April this year...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]