EEWORLDEEWORLDEEWORLD

Part Number

Search

ECCM7JA18-20.480M

Description
QUARTZ CRYSTAL RESONATOR, 20.48MHz, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN
CategoryPassive components    Crystal/resonator   
File Size121KB,4 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance  
Download Datasheet Parametric View All

ECCM7JA18-20.480M Overview

QUARTZ CRYSTAL RESONATOR, 20.48MHz, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN

ECCM7JA18-20.480M Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerECLIPTEK
package instructionROHS COMPLIANT, CERAMIC, SMD, 4 PIN
Reach Compliance Codecompliant
Other featuresAT-CUT CRYSTAL; BULK
Ageing3 PPM/YEAR
Crystal/Resonator TypePARALLEL - FUNDAMENTAL
Drive level100 µW
frequency stability0.003%
frequency tolerance15 ppm
JESD-609 codee4
load capacitance18 pF
Manufacturer's serial numberECCM7
Installation featuresSURFACE MOUNT
Nominal operating frequency20.48 MHz
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
physical sizeL3.2XB2.5XH0.8 (mm)/L0.126XB0.098XH0.031 (inch)
Series resistance80 Ω
surface mountYES
Terminal surfaceNickel/Gold (Ni/Au)

ECCM7JA18-20.480M Preview

ECCM7JA18-20.480M
Series
RoHS Compliant (Pb-free) 2.5mm x 3.2mm Ceramic
SMD Crystal
Frequency Tolerance/Stability
±15ppm at 25°C, ±30ppm over -30°C to +85°C
Mode of Operation
AT-Cut Fundamental
RoHS
Pb
ECCM7 J A 18 -20.480M
Nominal Frequency
20.480MHz
Load Capacitance
18pF Parallel Resonant
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
Aging at 25°C
Load Capacitance
Shunt Capacitance (C0)
Equivalent Series Resistance
Mode of Operation
Drive Level
Crystal Cut
Spurious Response
Storage Temperature Range
Insulation Resistance
20.480MHz
±15ppm at 25°C, ±30ppm over -30°C to +85°C
±3ppm/Year Maximum
18pF Parallel Resonant
5pF Maximum
80 Ohms Maximum
AT-Cut Fundamental
100µWatts Maximum
AT-Cut
>3dB (from Fo to Fo +5000ppm)
-40°C to +85°C
500 Megaohms Minimum at 100Vdc
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
Fine Leak Test
Flammability
Gross Leak Test
Mechanical Shock
Moisture Resistance
Moisture Sensitivity
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
MIL-STD-883, Method 1014, Condition A
UL94-V0
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 1004
J-STD-020, MSL 1
MIL-STD-202, Method 210, Condition K
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010, Condition B
MIL-STD-883, Method 2007, Condition A
MECHANICAL DIMENSIONS (all dimensions in millimeters)
PIN
1
CONNECTION
Crystal
Cover/Ground
Crystal
Cover/Ground
2.50
±0.10
MARKING
ORIENTATION
0.70 ±0.10
4
1
1.20
±0.10
3
2
0.90 ±0.10
(X4)
2
1.00
±0.10
(X4)
3
4
LINE MARKING
1
2
E20.4
E=Ecliptek Designator
XXXXX
XXXXX=Ecliptek
Manufacturing Identifier
3.20
±0.10
0.80 MAX
www.ecliptek.com | Specification Subject to Change Without Notice | Rev I 8/12/2010 | Page 1 of 4
ECCM7JA18-20.480M
Suggested Solder Pad Layout
All Dimensions in Millimeters
1.3 (X4)
1.3 (X4)
0.8
Solder Land
(X4)
0.4
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev I 8/12/2010 | Page 2 of 4
ECCM7JA18-20.480M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
High Temperature Infrared/Convection
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
3°C/second Maximum
150°C
175°C
200°C
60 - 180 Seconds
3°C/second Maximum
217°C
60 - 150 Seconds
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev I 8/12/2010 | Page 3 of 4
ECCM7JA18-20.480M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
Low Temperature Infrared/Convection 245°C
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
5°C/second Maximum
N/A
150°C
N/A
30 - 60 Seconds
5°C/second Maximum
150°C
200 Seconds Maximum
245°C Maximum
245°C Maximum 2 Times / 230°C Maximum 1 Time
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev I 8/12/2010 | Page 4 of 4
Does anyone have a code to make the menu transparent under evc4.0? Thank you in advance
Does anyone have a code to make the menu transparent under evc4.0? Thank you in advance...
old60 Embedded System
Getting Started with the ST SensorTile.box Sensor Kit (4) Programming Mode Experience
[i=s]This post was last edited by nich20xx on 2020-7-8 05:30[/i]1 Introduction SensorTile.box programming mode (Pro Mode) allows you to write/debug your own code on the SensorTile.box as needed to mee...
nich20xx ST MEMS Sensor Creative Design Competition
The Essence of Chinese Management
I saw an essay and found it very insightful, so I shared it with you. Chinese Management The tradition of Chinese management is to use Legalist management for the lower and operational levels, Confuci...
向农 Talking about work
How to create a Keil project for LPC2131 ucosii?
As the title says! Does anyone have an example of LPC2131 ucosii that needs to be compiled with Keil? If you have one, please send it to me for study. skdzhm@163.com...
skdzhm Real-time operating system RTOS
CC2530 Sensor Networking Experiment Code Tutorial
Some small code...
1456999234@qq.c RF/Wirelessly
Please tell me why the result of the debug window detection does not match the program design
I realize software startup adc12 sampling conversion in the timer interrupt program. The idea of writing the interrupt program is: first set ENC and ADC12SC [/font][/backcolor][backcolor=white][font=宋...
zhy3928551 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2200  2863  1444  1364  684  45  58  30  28  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号