Narrow SO (derate 8.70mW/°C above +70°C) ............696mW
Operating Temperature Range...............................0°C to +70°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Senior Software Engineer Qualifications: 1. Bachelor degree or above in software, computer, communication and other related majors, more than two years of development experience. 2. Proficient in C/C+...
I want to use jtag to download the program, but the USB blastercha shows unrecognized on the computer. I have tried many methods on the Internet, but it still doesn't work. The computer is win10 versi...
A host of virtual vulnerabilities can also affect physical security solutions. "Many network-based surveillance cameras have security issues," says Bruce Schneier, a security technology expert and wri...
I just bought a DN2540 MOS tube. I used the diode setting of a multimeter to measure and found that the drain-source voltage of the DN2540 is 0.316V and the source-drain voltage is 0.556V. Is this not...
Introduction: Design of automated test systems
Challenges
To ensure the quality and reliability of products delivered to customers, test managers and engineers use automated test system...[Details]
In the development of high-stability lasers, real-time monitoring of the working state of the laser is an issue that needs to be focused on. This system realizes the high-stability laser temperatur...[Details]
The hardware circuit principle is shown in Figure 1. In the specific design, each part should consider the anti-interference problem to minimize the impact of interference on the performance of the...[Details]
0 Introduction to the direct method of feedback linearization based on dynamic equilibrium state theory
The basic idea of the direct method of feedback linearization based on dynamic equilib...[Details]
Signal sources have developed to a very wide range today. We can classify them according to the frequency range: ultra-low frequency (0.1m～1kHz), audio (20Hz～20kHz), video (20kHz～10MHz), radio fre...[Details]
Adding "intelligence" to measurement systems is becoming more common as 8-bit microcontrollers are inexpensive, widely available, and can be programmed using today's common high-level languages, su...[Details]
Compared with traditional light sources, light-emitting diodes (LEDs) have many advantages, such as low operating voltage, high energy efficiency, small size and directional light. They can provide...[Details]
Demand Analysis
In an era of rapid information development, the process of electronicization of the financial system has also been greatly accelerated. As a platform that provides services 24 ...[Details]
In a Class D audio power amplifier, the preamplifier is a relatively important module. It is located at the front of the entire topology and completes the processing of the input signal source,...[Details]
At present, TPMS (tire pressure monitoring system) is mainly divided into two types, one is indirect type and the other is direct type. The direct TPMS system has been affected by its poor alarm ac...[Details]
1 Introduction
Intelligent software agents are software programs that can perform specific tasks for users, have a certain degree of intelligence, can autonomously perform some tasks, and ...[Details]
Abstract:
Under high dynamic conditions, combined with GEC's twelve-channel correlator GP2021, this paper discusses the structural design of GPS receivers and the key technologies inv...[Details]
Automatic target recognition (ATR) algorithms usually include algorithms for automatically detecting, tracking, identifying, and selecting attack points for targets. The complexity of the battlefi...[Details]
Abstract: In many SCART applications, due to the complex signal switching requirements, dedicated ICs are usually used to implement SCART connections. This will bring cost pressure to single SCART ...[Details]
The full name of RFID is Radio Frequency Identification, which uses radio frequency to realize data transmission between programmable controller (PLC) or microcomputer (PC) and identification, ther...[Details]
Recruitment
京公网安备 11010802033920号
EEWORLD
