As shown in the figure, the base address of AHBPERIPH_BASE is PERIPH_BASE+0x20000. How do I calculate the offset address of AHBPERIPH_BASE is 0x20000? By looking up the table, as shown in the followin...
Here are some tips: CC2600 is a Bluetooth controller, and 5529 is a MSP430 with USB function. Actually, this is a reference design, so you can guess first....
I can write to registers such as LCR, DLL, DLH, IER, and read them out, but I can't write to FCR. I wrote the code below. Can any brother or sister guide me? //Define related macros #define UART_BASE_...
A GPIO control demo apk compiled based on PX2 Function: Control the pin status of GPIO_0_D4 Note: The GPIO pin is High by default. Consider using infrared control first to get familiar with the infrar...
The Digital Signal Processing Library is a set of highly optimized functions that perform many common signal processing operations on fixed-point numbers for the MSP430 and MSP432 microcontrollers. Th...
Based on the traditional full-bridge circuit, a new circuit is studied using a single-quadrant circuit to expand the application field of the existing circuit topology. The voltage dual-quadrant Buck,...
Dong Yang, executive vice president of the China Association of Automobile Manufacturers, said on the 26th that according to the authorization of the Ministry of Industry and Information Technology...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
The program got stuck during LCD initialization. Through hardware debugging, it was found that it was stuck in the Delay_ms() function. Going to the definition, it was found to be a macro definition ...[Details]
The day before yesterday, I learned about STM's Systick and found it quite useful for precise timing. When I used CVAVR before, I found that the delay.h in it was very useful. So, I used STM32's...[Details]
1. The first project We are going to create the first project, which is mainly for project analysis, so that we can understand how CubeMX works and how to trace the code logic. Okay, no more nonsense...[Details]
introduction STM32 has many registers, which are difficult to remember, so the official packaged two sets of library functions. One is the standard library, but the official has not updated it on F7,...[Details]
When designing a product, if the application environment's requirements for power isolation are not considered, the product will be unstable due to improper design, and even high voltage may damage t...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
In order to strengthen the traceability management of recycling and utilization of power batteries for new energy vehicles, and to standardize and guide all relevant parties to fulfill their tracea...[Details]
As a leading company in automotive semiconductors, Freescale and Khronos Group have jointly launched an automotive multimedia embedded microprocessor i.MX35 with an integrated OpenVG hardware acceler...[Details]
//Observe the difference between feeding the dog and not feeding the dog, and use the LED indicator of the PB port for status indication. //Switch the LED indicator enable switch of the PB po...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
STM32 ADC multi-channel conversion Description: Use ADC to continuously collect 11 analog signals and transfer them to memory through DMA. ADC is configured to scan and continuously convert mode,...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
