I don’t want to go to work on Monday. I’ve been obsessed with running recently. After road running, I want to run cross-country, but cross-country equipment is too expensive...
Control battery output and prevent battery reverse connectionThe fourth figure should be able to be completely shut down. The output loop and the body diode of the PMOS tube are in opposite directions...
[backcolor=rgb(255,255,255)]Recently, I am using STM8 TIM4 timing interrupt to make a fixed frequency infrared signal length receiving and controlling LED light program, but I just can't execute it. C...
[i=s]This post was last edited by pigyong801 on 2017-1-3 17:32[/i] [backcolor=rgb(239, 245, 249)]I bought this aviation noise cancelling earphone (233621) online. The circuit design is average, the ef...
When high-definition YPbPr signals are coupled between circuits, DC coupling or AC coupling can be used. For the safety of the circuit, DC-isolated AC coupling is generally used. However, AC coupling ...
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
1. About FPU transplantation As long as the chip has FPU function, the use of FPU is generally enabled by default. You can also select it in the Options tab; 2. About the transplantation of DSP li...[Details]
Chip: STM32F107VCT6 Application Pin: THOUSANDS, RMII STM32CubeMX is very convenient to use ETH. The software comes with LWIP and configuration. This time, STM32F107VCT6+DP83848CVV is used. The MII a...[Details]
LAN8720 configuration: IP: 192.168.192.30 Gateway: 192.168.192.1 A high frequency of ARP packets is detected The content of the packet asks for the mac address of 192.168.192.1, and asks the resp...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
Different from 51, AVR and other single-chip microcomputers, the clock signal sources of msp430 include LFXT1, XT2 and DCO. 1. LFXT1: It can connect high-speed and low-speed crystal oscillators. In l...[Details]
sprintf is a function in the C language library that converts data types. There is a situation where In 51 MCU, define unsigned char temp; Then I want to use the serial port to print out temp in deci...[Details]
The independent watchdog of STM32 is driven by a dedicated internal 40Khz low-speed clock, that is, it is still effective even if the main clock fails. Here we need to note that the clock of the inde...[Details]
;Question: The 80C51 single-chip microcomputer has a fosc = 6MHz. It is required to use the T1 timer working mode 1 to perform a timing of 40ms. And P1.7 periodically outputs a rectangular wave with ...[Details]
6MHz crystal oscillator, using timer counter 1, using interrupt mode, through P1.0 to make a light emitting diode turn on for 100ms, turn off for 300ms, and repeat. Assembly programming is used to ac...[Details]
In the packaging process of a production line, every time the conveyor belt of the production line delivers a product to the packaging machine, the "SP" terminal outputs a pulse to the T1 terminal of...[Details]
The circuit shown in the figure requires that the light is off when the machine is turned on. Press the button once, and the light D1 will turn on and automatically turn off after a delay of 10 secon...[Details]
The following comes from - "cortex-M3 Definitive Guide" Special function register group: Program Status Registers (PSRs or xPSRs) Interrupt mask register group (PRIMASK, FAULTMASK, and BASEPRI) ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
