• Phase-Lock Loop Clock Distribution for Applications ranging
from 10MHz to 133MHz operating frequency
• Distributes one clock input to two banks of four outputs
• Separate output enable for each output bank
• External feedback (FBK) pin is used to synchronize the outputs
to the clock input
• Output Skew <200 ps
• Low jitter <200 ps cycle-to-cycle
• 1x, 2x, 4x output options (see table):
– IDT2308B-1 1x
– IDT2308B-2 1x, 2x
– IDT2308B-3 2x, 4x
– IDT2308B-4 2x
– IDT2308B-1H, -2H, and -5H for High Drive
• No external RC network required
• Operates at 3.3V V
DD
• Available in SOIC and TSSOP packages
DESCRIPTION:
The IDT2308B is a high-speed phase-lock loop (PLL) clock multiplier. It is
designed to address high-speed clock distribution and multiplication applica-
tions. The zero delay is achieved by aligning the phase between the incoming
clock and the output clock, operable within the range of 10 to 133MHz.
The IDT2308B has two banks of four outputs each that are controlled via two
select addresses. By proper selection of input addresses, both banks can be
put in tri-state mode. In test mode, the PLL is turned off, and the input clock
directly drives the outputs for system testing purposes. In the absence of an
input clock, the IDT2308B enters power down, and the outputs are tri-stated.
In this mode, the device will draw less than 25µA.
The IDT2308B is available in six unique configurations for both pre-
scaling and multiplication of the Input REF Clock. (See available options
table.)
The PLL is closed externally to provide more flexibility by allowing the user
to control the delay between the input clock and the outputs.
The IDT2308B is characterized for both Industrial and Commercial opera-
tion.
FUNCTIONAL BLOCK DIAGRAM
(-3, -4)
FBK
REF
16
1
2
(-5)
2
PLL
3
2
CLKA1
CLKA2
14
CLKA3
15
CLKA4
S2
S1
8
9
Control
Logic
(-2, -3)
2
6
CLKB1
7
CLKB2
10
CLKB3
11
CLKB4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2013
Integrated Device Technology, Inc.
OCTOBER 2013
DSC 6995/3
IDT2308B
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
DD
Rating
Supply Voltage Range
Input Voltage Range (REF)
Input Voltage Range
(except REF)
I
IK
(V
I
< 0)
I
OK
(V
O
< 0 or V
O
> V
DD
)
I
O
(V
O
= 0 to V
DD
)
V
DD
or GND
T
A
= 55°C
(in still air)
(3)
T
STG
Operating
Storage Temperature Range
Commercial Temperature
Range
Industrial Temperature
Range
-40 to +85
°C
–65 to +150
0 to +70
°C
°C
Continuous Current
Maximum Power Dissipation
±100
0.7
mA
W
Input Clamp Current
Terminal Voltage with Respect
to GND (inputs V
IH
2.5, V
IL
2.5)
Continuous Output Current
±50
mA
Max.
–0.5 to +4.6
–0.5 to +5.5
–0.5 to
V
DD
+0.5
–50
±50
mA
mA
Unit
V
V
V
V
I (2)
V
I
REF
CLKA1
CLKA2
V
DD
GND
CLKB1
CLKB2
S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
FBK
CLKA4
CLKA3
V
DD
GND
CLKB4
CLKB3
S1
SOIC/ TSSOP
TOP VIEW
Temperature
Operating
Temperature
PIN DESCRIPTION
Pin Number
REF
CLKA1
(1)
CLKA2
(1)
V
DD
GND
CLKB1
(1)
CLKB2
(1)
S2
(2)
Functional Description
Input Reference Clock, 5 Volt Tolerant Input
Clock Output for Bank A
Clock Output for Bank A
3.3V Supply
Ground
Clock Output for Bank B
Clock Output for Bank B
Select Input, Bit 2
Select Input, Bit 1
Clock Output for Bank B
Clock Output for Bank B
Ground
3.3V Supply
Clock Output for Bank A
Clock Output for Bank A
PLL Feedback Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150
°
C and a board trace length of 750 mils.
APPLICATIONS:
•
•
•
•
•
SDRAM
Telecom
Datacom
PC Motherboards/Workstations
Critical Path Delay Designs
S1
(2)
CLKB3
(1)
CLKB4
(1)
GND
V
DD
CLKA3
(1)
CLKA4
(1)
FBK
NOTES:
1. Weak pull down on all outputs.
2. Weak pull ups on these inputs.
2
IDT2308B
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
FUNCTION TABLE
(1)
SELECT INPUT DECODING
S2
L
L
H
H
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
S1
L
H
L
H
CLK A
Tri-State
Driven
Driven
Driven
CLK B
Tri-State
Tri-State
Driven
Driven
Output Source
PLL
PLL
REF
PLL
PLL Shut Down
Y
N
Y
N
AVAILABLE OPTIONS FOR IDT2308B
Device
IDT2308B-1
IDT2308B-1H
IDT2308B-2
IDT2308B-2
IDT2308B-2H
IDT2308B-2H
IDT2308B-3
IDT2308B-3
IDT2308B-4
IDT2308B-5H
Feedback From
Bank A or Bank B
Bank A or Bank B
Bank A
Bank B
Bank A
Bank B
Bank A
Bank B
Bank A or Bank B
Bank A or Bank B
Bank A Frequency
Reference
Reference
Reference
2 x Reference
Reference
2 x Reference
2 x Reference
4 x Reference
2 x Reference
Reference/2
Bank B Frequency
Reference
Reference
Reference/2
Reference
Reference/2
Reference
Reference or
Reference
(1)
2 x Reference
2 x Reference
Reference/2
NOTE:
1. Output phase is indeterminant (0° or 180° from input clock).
3
IDT2308B
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
ZERO DELAY AND SKEW CONTROL
To close the feedback loop of the IDT2308B, the FBK pin can be driven from any of the eight available output pins. The output driving the FBK pin
will be driving a total load of 7pF plus any additional load that it drives. The relative loading of this output (with respect to the remaining outputs) can adjust
the input-output delay.
For applications requiring zero input-output delay, all outputs including the one providing feedback should be equally loaded. If input-output delay
adjustments are required, use the Output Load Difference Chart to calculate loading differences between the feedback output and remaining outputs.
Ensure the outputs are loaded equally, for zero output-output skew.
REF TO CLKA/CLKB DELAY vs. OUTPUT LOAD DIFFERENCE BETWEEN FBK PIN AND CLKA/CLKB PINS
1500
1000
REF to CLKA/CLKB Delay (ps)
500
0
-30
-25
-20
-15
-10
-5
0
5
10
15
20
25
30
-500
-1000
-1500
OUTPUT LOAD DIFFERENCE BETWEEN FBK PIN AND CLKA/CLKB PINS ( pF)
[color=#000][font=Arial, Microsoft YaHei]Hello experts, the circuit is shown in the figure above. IA is a sine wave signal with a +2.5V DC component. After U27 removes the DC component, U20 takes the ...
The external voltage connected to pins 13 and 15 is 18V. What is the pulse amplitude output by pins 11 and 14? Can the 11 and 14 pins be directly connected to IR2110?...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
