• Phase-Lock Loop Clock Distribution for Applications ranging
from 10MHz to 133MHz operating frequency
• Distributes one clock input to two banks of four outputs
• Separate output enable for each output bank
• External feedback (FBK) pin is used to synchronize the outputs
to the clock input
• Output Skew <200 ps
• Low jitter <200 ps cycle-to-cycle
• 1x, 2x, 4x output options (see table):
– IDT2308A-1 1x
– IDT2308A-2 1x, 2x
– IDT2308A-3 2x, 4x
– IDT2308A-4 2x
– IDT2308A-1H and -2H for High Drive
• No external RC network required
• Operates at 3.3V V
DD
• Available in SOIC and TSSOP packages
DESCRIPTION:
The IDT2308A is a high-speed phase-lock loop (PLL) clock multiplier. It is
designed to address high-speed clock distribution and multiplication applica-
tions. The zero delay is achieved by aligning the phase between the incoming
clock and the output clock, operable within the range of 10 to 133MHz.
The IDT2308A has two banks of four outputs each that are controlled via two
select addresses. By proper selection of input addresses, both banks can be
put in tri-state mode. In test mode, the PLL is turned off, and the input clock
directly drives the outputs for system testing purposes. In the absence of an
input clock, the IDT2308A enters power down. In this mode, the device will
draw less than 12µA for Commercial Temperature range and less than 25µA
for Industrial temperature range, and the outputs are tri-stated.
The IDT2308A is available in six unique configurations for both pre-
scaling and multiplication of the Input REF Clock. (See available options
table.)
The PLL is closed externally to provide more flexibility by allowing the user
to control the delay between the input clock and the outputs.
The IDT2308A is characterized for both Industrial and Commercial opera-
tion.
FUNCTIONAL BLOCK DIAGRAM
(-3, -4)
FBK
REF
16
1
2
(-5)
2
PLL
3
2
CLKA1
CLKA2
14
CLKA3
15
CLKA4
S2
S1
8
9
Control
Logic
(-2, -3)
2
6
CLKB1
7
CLKB2
10
CLKB3
11
CLKB4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2004
Integrated Device Technology, Inc.
JULY 2004
DSC 6587/3
IDT2308A
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
DD
Rating
Supply Voltage Range
Input Voltage Range (REF)
Input Voltage Range
(except REF)
I
IK
(V
I
< 0)
I
O
(V
O
= 0 to V
DD
)
V
DD
or GND
T
A
= 55°C
(in still air)
(3)
T
STG
Operating
Temperature
Operating
Storage Temperature Range
Commercial Temperature
Range
Industrial Temperature
Range
-40 to +85
°C
–65 to +150
0 to +70
°C
°C
Continuous Current
Maximum Power Dissipation
±100
0.7
mA
W
Input Clamp Current
Continuous Output Current
Max.
–0.5 to +4.6
–0.5 to +5.5
–0.5 to
V
DD
+0.5
–50
±50
mA
mA
Unit
V
V
V
V
I (2)
V
I
REF
CLKA1
CLKA2
V
DD
GND
CLKB1
CLKB2
S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
FBK
CLKA4
CLKA3
V
DD
GND
CLKB4
CLKB3
S1
SOIC/ TSSOP
TOP VIEW
Temperature
PIN DESCRIPTION
Pin Number
REF
(1)
CLKA1
(2)
CLKA2
(2)
V
DD
GND
CLKB1
(2)
CLKB2
(2)
S2
(3)
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150
°
C and a board trace length of 750 mils.
Functional Description
Input Reference Clock, 5 Volt Tolerant Input
Clock Output for Bank A
Clock Output for Bank A
3.3V Supply
Ground
Clock Output for Bank B
Clock Output for Bank B
Select Input, Bit 2
Select Input, Bit 1
Clock Output for Bank B
Clock Output for Bank B
Ground
3.3V Supply
Clock Output for Bank A
Clock Output for Bank A
PLL Feedback Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
APPLICATIONS:
•
•
•
•
•
S1
(3)
CLKB3
(2)
CLKB4
(2)
GND
V
DD
CLKA3
(2)
CLKA4
(2)
FBK
SDRAM
Telecom
Datacom
PC Motherboards/Workstations
Critical Path Delay Designs
NOTES:
1. Weak pull down.
2. Weak pull down on all outputs.
3. Weak pull ups on these inputs.
2
IDT2308A
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
FUNCTION TABLE
(1)
SELECT INPUT DECODING
S2
L
L
H
H
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
S1
L
H
L
H
CLK A
Tri-State
Driven
Driven
Driven
CLK B
Tri-State
Tri-State
Driven
Driven
Output Source
PLL
PLL
REF
PLL
PLL Shut Down
Y
N
Y
N
AVAILABLE OPTIONS FOR IDT2308A
Device
IDT2308A-1
IDT2308A-1H
IDT2308A-2
IDT2308A-2
IDT2308A-2H
IDT2308A-2H
IDT2308A-3
IDT2308A-3
IDT2308A-4
Feedback From
Bank A or Bank B
Bank A or Bank B
Bank A
Bank B
Bank A
Bank B
Bank A
Bank B
Bank A or Bank B
Bank A Frequency
Reference
Reference
Reference
2 x Reference
Reference
2 x Reference
2 x Reference
4 x Reference
2 x Reference
Bank B Frequency
Reference
Reference
Reference/2
Reference
Reference/2
Reference
Reference or
Reference
(1)
2 x Reference
2 x Reference
NOTE:
1. Output phase is indeterminant (0° or 180° from input clock).
ZERO DELAY AND SKEW CONTROL
To close the feedback loop of the IDT2308A, the FBK pin can be driven from any of the eight available output pins. The output driving the FBK pin
will be driving a total load of 7pF plus any additional load that it drives. The relative loading of this output (with respect to the remaining outputs) can adjust
the input-output delay.
For applications requiring zero input-output delay, all outputs including the one providing feedback should be equally loaded. Ensure the outputs are
Urgently hiring senior engineers in electronics, communications and other related industries (part-time, no need to work in the office). If interested, please contact QQ: 3436403171, thank you!This co...
Hello everyone, I am learning FPGA recently. I use quartus11.1 to call modelsim-altera10.0c to simulate but the waveform is not displayed. I have set all the necessary settings in quartus and compared...
---《Fully Digital TI Solution Power Supply》The main power supply passed the functional test at 150V-DC. The MOSFET drive waveform is ideal.Now I only dare to try it at low voltage, not high voltage. I...
Every time I create a new project, I have to add the CSL header file, which is very troublesome. Is there any way to set it so that the CSL header file is added by default every time I create a new pr...
The official library of SAM4L Xplained Pro starter kit is huge, but if you call the official API function, you can get started quickly. In the future, I will release some routines that go deep into re...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
The power supply is the core component of a computer. Although it is not of high value, all computer components rely on the switching power adapter to provide energy, so the stability of a power su...[Details]
When developing electronic products with processors, how to improve anti-interference ability and electromagnetic compatibility?
1. The following systems should pay special attention to anti-...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
The biggest advantage of Profibus is that it is guaranteed by the stable international standard EN50170 and has been proven to be universal in practical applications. It has been widely used in man...[Details]
The programmable controller directly controls the stepper motor, which can significantly reduce the cost of the control system of the modular machine tool automatic production line. The article int...[Details]
1. Why do we need to do electromagnetic compatibility design for products?
Answer: To meet product functional requirements, reduce debugging time
,
make products meet the requirements o...[Details]
1. Overview
With the development of science and technology, PLC is increasingly used in industrial control. The reliability of PLC control systems directly affects the safe production and economic o...[Details]
Improving the coordination of material handling and internal transportation between departments in modern factories is an important measure to achieve full automation of production. Traditional mat...[Details]
1 Introduction
When studying electronic courses such as "Electronic Circuits" and "Signal Processing", college students only understand the real signal characteristics in theory. They cannot r...[Details]
1. Introduction
Due to the good programmability and superior performance of FPGA, the number of embedded systems using FPGA chips in LCD splicing screens is increasing rapidly, especially in t...[Details]
Infineon's ICL8001G adopts a single-stage flyback and PFC controller with quasi-resonant operation mode, with a power factor greater than 98%, LED driver efficiency up to 90%, an operating voltage up ...[Details]
Talking about work
京公网安备 11010802033920号
EEWORLD
