PTN
www.vishay.com
Vishay Dale Thin Film
Commercial Thin Film Chip Resistor,
Surface Mount Chip
FEATURES
•
•
•
•
Actual Size
1505
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic E of
MIL-PRF-55342.
•
•
•
•
•
•
•
•
Moisture resistant
High purity alumina substrate
Non-standard values available
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Non-inductive
Very low noise and voltage coefficient (< - 30 dB)
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 m
Epoxy bondable termination available
Sulfur resistant (per ASTM B809-95 humid vapor test)
Material categorization: For definitions please see
www.vishay.com/doc?99912
CONSTRUCTION
Passivation
Tantalum Nitride
Resistive Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
Note
*
Lead (Pb)-containing terminations are not RoHS-compliant.
Exemptions may apply.
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tantalum nitride
10
to 3 M
± 25 ppm/°C to ± 100 ppm/°C
± 0.1 % to ± 5 %
R
± 0.03 %
-
0.1 ppm/V
75 V to 200 V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
< - 30 dB
-
CONDITIONS
-
-
- 55 °C to + 125 °C
+ 25 °C
2000 h at 70 °C
-
-
-
-
-
-
-
COMPONENT RATINGS
CASE SIZE
(1)
POWER RATING (mW)
0402
50
0502
100
0505
150
0603
150
0705
200
0805
200
1005
250
1010
500
1206
400
1505
400
2208
750
2010
800
2512
1000
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
Revision: 07-Mar-12
WORKING VOLTAGE (V)
75
75
75
75
100
100
100
150
200
150
150
200
200
RESISTANCE RANGE ()
20 to 51.1K
20 to 65K
20 to 130K
10 to 130K
10 to 301K
10 to 301K
10 to 360K
50 to 600K
10 to 1M
10 to 1M
10 to 1.75M
10 to 2M
10 to 3M
Document Number: 60026
76
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
PTN
www.vishay.com
Vishay Dale Thin Film
DIMENSIONS
in inches
D
T
E
L
W
CASE SIZE
0402
0502
0505
0603
0705, 0805
(1)
1005
1010
1206
1505
2010
2208
2512
L
0.042 ± 0.008
0.055 ± 0.006
0.055 ± 0.006
0.064 ± 0.006
0.080 ± 0.006
0.105 ± 0.007
0.105 ± 0.007
0.126 ± 0.008
0.155 ± 0.007
0.209 ± 0.009
0.230 ± 0.007
0.259 ± 0.009
W
0.022 ± 0.005
0.025 ± 0.005
0.050 ± 0.005
0.032 ± 0.005
0.050 ± 0.005
0.050 ± 0.005
0.100 ± 0.005
0.063 ± 0.005
0.050 ± 0.005
0.098 ± 0.005
0.075 ± 0.005
0.124 ± 0.005
T
0.012 to 0.033
0.012 to 0.033
0.012 to 0.033
0.020 max.
0.015 to 0.033
0.015 to 0.033
0.015 to 0.033
0.015 to 0.033
0.015 to 0.033
0.015 to 0.033
0.015 to 0.033
0.015 to 0.033
D
0.010 ± 0.005
0.010 ± 0.005
0.010 ± 0.005
0.012 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
E
0.010 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
0.015 ± 0.005
0.020 + 0.005/ - 0.010 0.020 + 0.005/ - 0.010
0.015 ± 0.005
0.020 ± 0.005
0.020 ± 0.005
0.020 ± 0.005
0.015 ± 0.005
0.020 ± 0.005
0.020 ± 0.005
0.020 ± 0.005
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
ENVIRONMENTAL TESTS
(Vishay Performance vs. MIL-PRF-55342 Requirements)
ENVIRONMENTAL TEST
Resistance Temperature Characteristic
Max. Ambient Temp. at Rated Wattage
Max. Ambient Temp. at Power Derating
Thermal Shock
Low Temperature Operation
Short Time Overload
High Temperature Exposure
Resistance to Soldering Heat
Moisture Resistance
Life + 70 °C at 1000 h
Insulation Resistance
R
R
R
R
R
R
R
LIMITS MIL-PRF-55342
CHARACTERISTIC “E”
± 25 ppm/°C
+ 70 °C
+ 150 °C
± 0.1 %
± 0.1 %
± 0.10 %
± 0.1 %
± 0.2 %
± 0.2 %
± 0.50 %
10 000
minimum
TYPICAL VISHAY
PERFORMANCE
± 15 ppm/°C
+ 70 °C
+ 150 °C
± 0.040 %
± 0.001 %
± 0.002 %
± 0.04 %
± 0.008 %
± 0.004 %
± 0.02 %
> 100 000 M
Revision: 07-Mar-12
Document Number: 60026
77
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
