The AS1129 is a low power voltage regulator. This device is an excellent choice for use in battery-powered applications such as
cordless telephones, radio control systems, and portable computers. The AS1129 features very low quiescent current and very low
dropout voltage of 0.4 volts. This includes a tight initial tolerance of
±
1% max, and very low output temperature coefficient, making
the AS1129 useful as a low-power voltage reference.
The error flag output feature is used as power-on reset for warning of a low output voltage, due to falling voltage input of batteries.
The AS1129 is offered TO-92, SOT-223, TO-220, TO-252 and TO-263 in 3 & 5 leads.
ORDERING INFORMATION
TO-92
AS1129N-X
SOT-223
3-PIN
AS1129M3-X
TO-220
3-PIN
AS1129U-X
TO-263
3/5-PIN
AS1129T-X
TO-263
5-PIN
AS1129T3-X
TO-252
3/5-PIN
AS1129R-X
Oper. Temp.
Range
-40°C to +125°C
X= Output Voltage (2.5V, 3.3V or 5.0V)
Consult factory for other fixed voltages.
SOT-223 (M3)
AS1129
1
2
3
1
PIN CONNECTIONS
TO-263-5 (T)
1) OUTPUT
2) SENSE/ ADJ
3) GND
4) SHDN
4) V
IN
TO-263-3 (T)
TO-220-3 (U)
TO-252 (R)
AS1129
3
2
1
V
IN
GND
V
OUT
V
IN
TO-92 (N)
1
2
3
AS1129
2
3
AS1129
1 2 3 4 5
AS1129
1
2
3
V
IN
GND V
OUT
GND
V
OUT
Top View
V
OUT
GND V
IN
Front View
Top View
Top View
V
OUT
GND V
IN
Bottom View
SHDN
V
OUT
<0.25V
>2.8V
NC
OFF
ON
ON
Front View
Rev. 10/11/00
AS1129
ABSOLUTE MAXIMUM RATINGS
Power Dissipation……………………...… Internally Limited
Lead Temp. (Soldering, 5 Seconds)…………….……. 260°C
Storage Temperature Range……………… -65°C to + 150°C
Operating Junction Temperature Range
AS1129……………………………..… -40°C to + 125°C
Maximum Input Supply Voltage....................................... +20V
Shutdown Input Voltage ...................................... -0.6V to 6.5V
ELECTRICAL CHARACTERISTICS
at V
S
= ±15V, T
A
= 25°C, unless otherwise specified.
Boldface
applies over the full
operating temperature range.
PARAMETER
2.5V Version
Output Voltage
Reverse Output Current
3.3V Version
Output Voltage
Reverse Output Current
5V Version
Output Voltage
Reverse Output Current
All Voltage Options
Output Voltage
Temperature Coefficient
Line Regulation (Note 3)
Load Regulation (Note 3)
Dropout Voltage
(Note 5)
20
(Note 1)
6V
≤
V
IN
≤20V
(Note 4)
I
L
= 1 to 500mA
I
L
= 0.1 to 1mA
I
L
= 1mA
I
L
= 500mA
Ground Current
I
L
= 1mA
I
L
= 10mA
I
L
= 50mA
I
L
= 100mA
I
L
= 500mA
V
OUT
= 0
V
IN
– V
OUT
1V (Avg), V
RIPPLE
= 0.5Vp-p
fripple = 120Hz, I
LOAD
= 500mA, T
J
= 25°C
V
IN
= -20V, V
OUT
= 0V
1.5
0.04
0.13
0.42
100
350
1.5
4.0
7
200
58
50
1.0
100
10
0.20
0.30
0.16
0.25
0.55
0.70
150
500
2.5
7.0
14
500
ppm/°C
%max
%max
V
1mA
≤I
L
≤
500mA
V
OUT
= 2.5V, V
IN
= 0V
CONDITIONS
(Note 2)
Typ.
AS1129
Min
Max
2.525
2.550
25
3.333
3.382
25
5.050
5.120
25
2.475
2.450
UNITS
2.5
2.5
16
3.3
3.3
16
5.0
5.0
16
V
µA
V
µA
V
µA
1mA
≤I
L
≤
500mA
V
OUT
= 3.3V, V
IN
= 0V
3.267
3.217
1mA
≤I
L
≤
500mA
V
OUT
= 5.0V, V
IN
= 0V
4.950
4.880
µA
mA
mA
dB
mA
Current Limit
Ripple Rejection
Input Reverse Leakage Current
Rev. 10/11/00
AS1129
Note 1:
Output or reference voltage temperature coefficients defined as the worst-case voltage change divided by the total temperature range.
Note 2:
Unless otherwise specified all limits are guaranteed for T
J
= 25°C, V
IN
= 6V, I
L
= 100µA and C
L
= 1µF. Additional conditions for the 8-pin versions are
feedback tied to 5V tap and output tied to output sense (V
OUT
= 5V) and V
SHUTDOWN
≤
0.8V.
Note 3:
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are
covered under the specification for thermal regulation.
Note 4:
Line regulation for the AS1129 is tested at 150°C for I
L
= 1 mA. For I
L
= 100µA and T
J
= 125°C, line regulation is guaranteed by design to 0.2%. See typical
performance characteristics for line regulation versus temperature and load current.
Note 5:
Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value measured at 1V differential at
very low values of programmed output voltage, the minimum input supply voltage of 2V (2.3V over temperature) must be taken into account.
Note 6:
Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nominal reference voltage measured at 6V input. To
express these thresholds in terms of output voltage change, multiply by the error amplifier gain = V
OUT
/V
REF
= (R1 + R2)/R2. For example, at a programmed output
voltage of 5V, the Error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds remain constant as a percent of V
OUT
as
V
OUT
is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed.
APPLICATION HINTS
EXTERNAL CAPACITORS
The stability of the AS1129 requires a 2.2µF or greater capacitor
between output and ground. Oscillation could occur without this
capacitor. Most types of tantalum or aluminum electrolytic
works fine here. For operations of below -25°C solid tantalum is
recommended since the many aluminum types have electrolytes
the freeze at about -30°C. The ESR of about 5Ω or less and
resonant frequency above 500kHz are the most important
parameters in the value of the capacitor. The capacitor value can
be increased without limit.
At lower values of output current, less output capacitance is
required for stability. For the currents below 10mA the value of
the capacitor can be reduced to 0.5µF and 0.15µF for 1mA. More
output capacitance needed for the 8-pin version at voltages below
5V since it runs the error amplifier at lower gain. At worst case
5µF or greater must be used for the condition of 250mA load at
1.23V output.
The AS1129, unlike other low dropout regulators will remain
stable and in regulation with no load in addition to the internal
voltage divider.
This feature is especially important in
application like CMOS RAM keep-alive. When setting the output
voltage of the AS1129, a minimum load of 10mA is
recommended.
If there is more than 10 inches of wire between the input and the
AC filter capacitor or if a battery is used as the input then a 0.1µF
tantalum or aluminum electrolytic capacitor should be placed
from the input to the ground.
Instability can occur if there is stray capacitance to the AS1129
feedback terminal (pin 7). This could cause more problems when
using a higher value of external resistors to set the output voltage.
This problem can be fixed by adding a 100pF capacitor between
output and feedback and increasing the output capacitor to at least
3.3µF.
ERROR DETECTION COMPARATOR OUTPUT
The Comparator produces a logic low output whenever the AS1129
output falls out of regulation by more than around 5%. This is around
60mV offset divided by the 1.235 reference voltage. This trip level
remains 5% below normal regardless of the programmed output
voltage of the regulator. Figure 1 shows the timing diagram depicting
the ERROR signal and the regulator output voltage as the AS1129
input is ramped up and down. The ERROR signal becomes low at
around 1.3V input, and goes high around 5V input (input voltage at
which Vout = 4.75). Since the AS1129’s dropout voltage is load
dependent, the input voltage trip point (around 5V) will vary with the
load current. The output voltage trip point (approx. 4.75V) does not
vary with load.
The error comparator has an open-collector output, which requires an
external pull-up resistor. Depending on the system requirements the
resistor may be returned to 5V output or other supply voltage. In
determining the value of this resistor, note that the output is rated to
sink 400µA, this value adds to battery drain in a low battery
condition. Suggested values range from 100K to 1MΩ. If the output
is unused this resistor is not required.
PROGRAMMING THE OUTPUT VOLTAGE OF AS1129
The AS1129 may be pin-strapped for 5V using its internal voltage
divider by tying Pin 1 (output) to Pin 2 (sense) and Pin 7 (feedback)
to Pin 6 (5V Tap).
SHUTDOWN
4.75V
OUTPUT
VOLTAGE
V
OUT
V
IN
8
5
1
AS1129
ERROR*
GND
3, 6, 7
2
ADJ
+
5.0V
INPUT
VOLTAGE
+
1.3V
+
+
Figure .2. Adjustable Voltage Regulator
* See Application Information.
Figure 1. ERROR Output Timing
Rev. 10/11/00
AS1129
Also, it may be programmed for any output voltage between its
1.235V reference and its 30V maximum rating. As seen in
Figure 2, an external pair of resistors is required.
Refer to the below equation for the programming of the output
voltage:
V
OUT
= V
REF
×
(1 + R
1
/ R
2
)+ I
FB
R
1
The V
REF
is 1.235 and I
FB
is the feedback bias current, nominally
-20nA. The minimum recommended load current of 1
µA
forces
an upper limit of 1.2 MΩ on value of R
2
. If no load is presented
the I
FB
produces an error of typically 2% in V
OUT
, which may be
eliminated at room temperature by trimming R
1
. To improve the
accuracy choose the value of R2 = 100k this reduces the error by
0.17% and increases the resistor program current by 12µA. Since
the AS1129 typically draws 60
µA
at no load with Pin 2 open-
circuited this is a small price to pay
REDUCING OUTPUT NOISE
It may be an advantage to reduce the AC noise present at the output.
One way is to reduce the regulator bandwidth by increasing the size of
the output capacitor. This is the only way that noise can be reduced
on the 3 lead AS1129 but is relatively inefficient, as increasing the
capacitor from 1µF to 220µF only decreases the noise from 430µV to
160µV Vrms for a 100kHz bandwidth at 5V output.
Noise could also be reduced fourfold by a bypass capacitor across R
1
,
since it reduces the high frequency gain from 4 to unity. Pick
C
BYPASS
≅
1 / 2πR
1
×
200 Hz
or choose 0.01µF. When doing this, the output capacitor must be
increased to 3.3µF to maintain stability. These changes reduce the
output noise from 430µV to 100µV Vrms for a 100kHz bandwidth at
5V output. With the bypass capacitor added, noise no longer scales
with output voltage so that improvements are more dramatic at higher
output voltages.
HEAT SINK REQUIREMENTS
Depending on the maximum ambient temperature and maximum
power dissipation a heat sink may be required with the AS1129.
The junction temperature range has to be within the range
specified under Absolute Maximum Ratings under all possible
operating conditions. To find out if a heat sink is required, the
maximum power dissipation of the device needs to be calculated.
This is the maximum specific AC voltage that must be taken into
consideration at input. Figure 3 shows the condition and power
dissipation which should be calculated with the following
formula:
P
TOTAL
= (V
IN
- 5) * I
L
+ (V
IN
) I
G
Next step is to calculate the temperature rise T
R
(max). T
J
(max)
maximum allowable junction temperature, T
A
(max) maximum
ambient temperature :
T
R
(max) = T
J
(max) - T
A
(max)
Junction to ambient thermal resistance
θ
(J-A)
can be calculated
after determining of P
TOTAL &
T
R
(max):
θ
(J-A)
= T
R
(max)/P
(max)
If the
θ
(J-A)
is 60°C/W or higher, the device could be operated
without a heat sink. If the value is below 60°C/W then the heat
sink is required and the thermal resistance of the heat sink can be
The circle drawn by Dogs102x6_circleDraw is stationary. What I want is a circle displayed on the LCD that can change with the position of the center of the circle, a moving circle....
[img]http://www.techor.com/syssite/home/shop/1/pictures/productsimg/big/281.JPG[/img] ◆ Completely replace S3C2440 with better cost performance◆ There is no device on the back of the module, which is ...
Use TI routines to extract some sub-functions and make a dual closed-loop speed regulation of a DC motor. The buttons can be used to accelerate, decelerate, and load forward and reverse....
Hello everyone, I am working on a card reader program for RC522 recently. I have implemented card password verification, password modification, data addition and subtraction operations on the board. I...
[i=s]This post was last edited by jefferysimon on 2020-9-4 16:26[/i]Company Profile:
Shenzhen Yudi Technology Co., Ltd. was established in 2011 and covers an area of 2,000 square meters. Since its est...
The radio frequency identification (RFID) market is experiencing strong growth, with sales reaching $1.7 billion in 2004 and expected to reach $5.9 billion in 2008. This surge in demand is driven b...[Details]
Emulation Features
Emulation provides a set of standard operations for integration and debugging. Some of its main features are as follows:
BreakpointsA
common feature of emulatio...[Details]
Portable devices with audio functions (such as portable media players and multimedia mobile phones) require long audio playback time, that is, long battery life. To extend the battery life of port...[Details]
1 Introduction
In recent years, with the rapid growth of mobile phones and MP4 video players, it is estimated that the production of mobile phones this year will reach 1 billion units, and...[Details]
When you hear the word digital TV, you may feel fresh and excited, but when it comes to what digital TV is and what it can bring us, you may still be confused. You must be very eager to understa...[Details]
Preface
In recent years, many compact portable electronic products have been developed, such as mobile phones, digital cameras, MP3, MP4, PDA, GPS and DVD, etc. They are not only small in size...[Details]
In today's world, terrorism poses a severe challenge to social development, national stability and human progress. "Terrorism, political corruption and environmental pollution" are known as the thr...[Details]
0Introduction
As a service robot in the field of medical care, the application of smart wheelchairs makes extensive use of mobile robot technology. The key technologies involved in the researc...[Details]
1. Introduction
Rolling bearings are the most widely used general mechanical components in various rotating machines. Whether their operating status is normal often directly affects the perfo...[Details]
With a 31-step dimming range, existing LED drivers offer good dimming capabilities, providing smooth backlight boosting or dimming effects for LCD displays. However, when the end application involv...[Details]
Abstract:
Using TMS320F2812 DSP chip as the control unit, without any gate control device control, the rich software resources of DSP 2812 are used to achieve equal precision measurement. A...[Details]
With the rapid development of my country's power industry, the power system has higher requirements for the collection of power generation, transmission, distribution and consumption. As a prerequis...[Details]
Introduction
As a kind of biometric identification, fingerprint recognition has incomparable advantages in identity recognition over other means: human fingerprints are unique and stable; wit...[Details]
Abstract
Modbus protocol has become the first choice of communication protocol in the current industrial field due to its openness, transparency, low cost and easy development. This paper int...[Details]
Test equipment manufacturers are constantly challenged to develop new test solutions that meet the latest product testing needs of their customers, and they often design specialized hardware t...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
