EEWORLDEEWORLDEEWORLD

Part Number

Search

HIP6302VCB-T

Description
SWITCHING CONTROLLER, 1500kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, MS-012AC, SOIC-16
CategoryPower/power management    The power supply circuit   
File Size939KB,20 Pages
ManufacturerRenesas Electronics Corporation
Websitehttps://www.renesas.com/
Download Datasheet Parametric Compare View All

HIP6302VCB-T Overview

SWITCHING CONTROLLER, 1500kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, MS-012AC, SOIC-16

HIP6302VCB-T Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerRenesas Electronics Corporation
Parts packaging codeSOIC
package instructionSOP, SOP16,.25
Contacts16
Reach Compliance Codenot_compliant
ECCN codeEAR99
Analog Integrated Circuits - Other TypesSWITCHING CONTROLLER
control modeCURRENT/VOLTAGE-MODE
Control TechnologyPULSE WIDTH MODULATION
Maximum input voltage5.25 V
Minimum input voltage4.75 V
Nominal input voltage5 V
JESD-30 codeR-PDSO-G16
JESD-609 codee0
length9.9 mm
Humidity sensitivity level1
Number of functions1
Number of terminals16
Maximum operating temperature70 °C
Minimum operating temperature
Package body materialPLASTIC/EPOXY
encapsulated codeSOP
Encapsulate equivalent codeSOP16,.25
Package shapeRECTANGULAR
Package formSMALL OUTLINE
Peak Reflow Temperature (Celsius)240
Certification statusNot Qualified
Maximum seat height1.75 mm
surface mountYES
Switch configurationPHASE-SHIFT
Maximum switching frequency1500 kHz
Temperature levelCOMMERCIAL
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formGULL WING
Terminal pitch1.27 mm
Terminal locationDUAL
Maximum time at peak reflow temperature30
width3.9 mm

HIP6302VCB-T Preview

HIP6301V, HIP6302V
NOT RECOMMENDED FOR NEW DESIGNS
NO RECOMMENDED REPLACEMENT
contact our Technical Support Center at
1-888-INTERSIL or www.intersil.com/tsc
DATASHEET
FN9034
Rev 3.00
May 5, 2008
Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
The HIP6301V and HIP6302V control microprocessor
CORE voltage regulation by driving up to four
synchronous-rectified buck channels in parallel. Multiphase
buck converter architecture uses interleaved timing to
multiply ripple frequency and reduce input and output ripple
currents. Lower ripple results in fewer components, lower
component cost, reduced power dissipation, and a smaller
implementation area. The HIP6301V is a versatile 2- to
4-phase controller and the HIP6302V is a cost-saving
dedicated 2-phase controller.
The HIP6301V and HIP6302V are exact pin compatible
replacements for their predecessor parts, the HIP6301 and
HIP6302. They are the first controllers to incorporate
Dynamic VID™ technology to manage the output voltage
and current during on-the-fly DAC changes. Using Dynamic
VID, the HIP6301V and HIP6302V detect changes in the
VID code, and gradually change the reference in 25mV
increments until reaching the new value. By gradually
changing the reference setting, in-rush current and the
accompanying voltage swings remain negligibly small.
Intersil offers a wide range of MOSFET drivers to form highly
integrated solutions for high-current, high slew-rate
applications. The HIP6301V and HIP6302V regulate output
voltage, balance load currents and provide protective
functions for two to four synchronous-rectified buck
converter channels. These parts feature an integrated
high-bandwidth error amplifier for fast, precise regulation
and a 5-bit DAC for the digital interface to program the 0.8%
accuracy. A window comparator toggles PGOOD if the
output voltage moves out of range, and acts to protect the
load in case of over voltage.
Current sensing is accomplished by reading the voltage
developed across the lower MOSFETs during their
conduction intervals. Current sensing provides the needed
signals for precision droop, channel-current balancing, load
sharing, and overcurrent protection. This saves cost by
taking advantage of the power device’s parasitic on
resistance.
Features
• Multi-Phase Power Conversion
• Precision CORE Voltage Regulation
- ±0.8% System Accuracy Over-Temperature
• Microprocessor Voltage Identification Input
- Dynamic-VID Technology
- 5-bit VID Decoder
• Precision Channel-Current Balance
• Overcurrent Protection
• Lossless Current Sensing
• Programmable “Droop” Voltage
• Fast Transient Response
• Selection of 2-, 3-, or 4-Phase Operation
• High Ripple Frequency (100kHz to 6MHz)
• Pb-Free Available (RoHS Compliant)
Ordering Information
PART
NUMBER
HIP6301VCB*
HIP6301VCBZ*
(Note)
PART
MARKING
HIP6301VCB
HIP6301VCBZ
TEMP.
RANGE
(°C)
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
PKG.
DWG. #
M20.3
M20.3
M20.3
M16.15
M16.15
PACKAGE
20 Ld SOIC
20 Ld SOIC
(Pb-free)
20 Ld SOIC
(Pb-free)
16 Ld SOIC
16 Ld SOIC
(Pb-free)
HIP6301VCBZA* HIP6301VCBZ
(Note)
HIP6302VCB*
HIP6302VCBZ*
(Note)
HIP6302VCB
HIP6302VCBZ
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on
reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach materials
and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which
is RoHS compliant and compatible with both SnPb and Pb-free
soldering operations. Intersil Pb-free products are MSL classified at Pb-
free peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
FN9034 Rev 3.00
May 5, 2008
Page 1 of 20
HIP6301V, HIP6302V
Pinouts
HIP6301V
(20 LD SOIC
TOP VIEW
VID4 1
VID3 2
VID2 3
VID1 4
VID0 5
COMP 6
FB 7
FS/DIS 8
GND 9
VSEN 10
20 V
CC
19 PGOOD
18 PWM4
17 ISEN4
16 ISEN1
15 PWM1
14 PWM2
13 ISEN2
12 ISEN3
11 PWM3
VID4 1
VID3 2
VID2 3
VID1 4
VID0 5
COMP 6
FB 7
FS/DIS 8
HIP6302V
(16 LD SOIC
TOP VIEW
16 V
CC
15 PGOOD
14 ISEN1
13 PWM1
12 PWM2
11 ISEN2
10 VSEN
9 GND
FN9034 Rev 3.00
May 5, 2008
Page 2 of 20
HIP6301V, HIP6302V
HIP6301V Block Diagram
PGOOD
VCC
POWER-ON
RESET (POR)
VSEN
X 0.9
+
UV
-
S
+
OV
X1.15
-
OV
LATCH
THREE-STATE
CLOCK AND
SAWTOOTH
GENERATOR
+
FS/DIS
-
+
PWM
-
PWM1
SOFT-
START
AND FAULT
LOGIC
+
-
+
PWM
-
PWM2
COMP
+
-
+
PWM
-
PWM3
VID0
VID1
VID2
VID3
VID4
DYNAMIC
VID
D/A
+
+
E/A
-
-
+
PWM
-
PWM4
FB
CURRENT
CORRECTION
PHASE
NUMBER
CHANNEL
DETECTOR
ISEN1
I_TOT
-
OC
+
I_TRIP
+
ISEN2
ISEN3
+
+
+
ISEN4
GND
FN9034 Rev 3.00
May 5, 2008
Page 3 of 20
HIP6301V, HIP6302V
HIP6302V Block Diagram
PGOOD
VCC
POWER-ON
RESET (POR)
VSEN
X 0.9
+
UV
-
S
+
OV
X1.15
-
OV
LATCH
TRI-STATE
CLOCK AND
SAWTOOTH
GENERATOR
+
FS/DIS
-
+
PWM
-
PWM1
SOFT-
START
AND FAULT
LOGIC
COMP
+
VID0
VID1
VID2
VID3
VID4
DYNAMIC
VID
D/A
-
+
PWM
-
PWM2
+
E/A
-
FB
CURRENT
CORRECTION
I_TOT
-
OC
+
I_TRIP
ISEN1
+
+
ISEN2
GND
FN9034 Rev 3.00
May 5, 2008
Page 4 of 20
HIP6301V, HIP6302V
HIP6301V and HIP6302V Functional Pin Descriptions
HIP6301V
(20 LD SOIC
TOP VIEW
VID4 1
VID3 2
VID2 3
VID1 4
VID0 5
COMP 6
FB 7
FS/DIS 8
GND 9
VSEN 10
20 V
CC
19 PGOOD
18 PWM4
17 ISEN4
16 ISEN1
15 PWM1
14 PWM2
13 ISEN2
12 ISEN3
11 PWM3
VID4 1
VID3 2
VID2 3
VID1 4
VID0 5
COMP 6
FB 7
FS/DIS 8
HIP6302V
(16 LD SOIC
TOP VIEW
16 V
CC
15 PGOOD
14 ISEN1
13 PWM1
12 PWM2
11 ISEN2
10 VSEN
9 GND
VID4, VID3, VID2, VID1 and VID0
(Pins 1 thru 5 - Both Parts)
Voltage Identification inputs. The HIP6301V and HIP6302V
decode the VID bits to establish the reference voltage (see
Table 1). Each pin has an internal 20µA pull-up current source
to 2.5V making the parts compatible with CMOS and TTL
logic from 5V down to 2.5V. When a VID change is detected,
the reference voltage slowly ramps up or down to the new
value in 25mV steps. VID input levels above 2.9V may
produce an reference-voltage offset inaccuracy.
PWM1 (Pin 15 - HIP6301V, Pin 13 - HIP6302V),
PWM2 (Pin 14 - HIP6301V, Pin 12 - HIP6302V),
PWM3 (Pin 11 - HIP6301V only) and PWM4
(Pin 18 - HIP6301V only)
PWM outputs for each channel. Connect these pins to the
PWM input of the external MOSFET driver. For HIP6301V
systems using 3 channels, connect PWM4 high. For two
channel systems, connect PWM3 and PWM4 high.
COMP (Pin 6 - Both Parts)
Output of the internal error amplifier. Connect this pin to the
external feedback and compensation network.
ISEN1 (Pin 16 - HIP6301V, Pin 14 - HIP6302V),
ISEN2 (Pin 13 - HIP6301V, Pin 11 - HIP6302V),
ISEN3 (Pin 12 - HIP6301V only) and ISEN4
(Pin 17 - HIP6301V only)
Current sense inputs from the individual converter channel’s
phase nodes. Unused sense lines MUST be left open.
FB (Pin 7 - Both Parts)
Inverting input of the internal error amplifier.
PGOOD (Pin 19 - HIP6301V, Pin 15 - HIP6302V)
Power-good. This pin is an open-drain logic signal that
indicates when the microprocessor CORE voltage (VSEN
pin) is within specified limits and soft-start has timed out.
FS/DIS (Pin 8 - Both Parts)
Channel frequency, F
SW
, select and disable. A resistor from
this pin to ground sets the switching frequency of the
converter. Pulling this pin to ground disables the converter
and three states the PWM outputs. See Figure 10.
V
CC
(Pin 20 - HIP6301V, Pin 16 - HIP6302V)
Bias supply. Connect this pin to a 5V supply.
GND (Pin 9 - Both Parts)
Bias and reference ground. All signals are referenced to this
pin.
VSEN (Pin 10 - Both Parts)
Power-good monitor input. Connect to the microprocessor CORE
voltage.
FN9034 Rev 3.00
May 5, 2008
Page 5 of 20

HIP6302VCB-T Related Products

HIP6302VCB-T HIP6301VCBZ HIP6301VCB-T HIP6301VCB HIP6302VCBZ-T HIP6302VCB
Description SWITCHING CONTROLLER, 1500kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, MS-012AC, SOIC-16 Microprocessor CORE Voltage Regulator Multiphase Buck PWM Controller; SOIC20; Temp Range: 0° to 70° SWITCHING CONTROLLER, 1500kHz SWITCHING FREQ-MAX, PDSO20, PLASTIC, MS-013AC, SOIC-20 SWITCHING CONTROLLER, 1500kHz SWITCHING FREQ-MAX, PDSO20, PLASTIC, MS-013AC, SOIC-20 Microprocessor CORE Voltage Regulator Multiphase Buck PWM Controller; SOIC16; Temp Range: 0° to 70° SWITCHING CONTROLLER, 1500kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, MS-012AC, SOIC-16
Is it Rohs certified? incompatible conform to incompatible incompatible conform to incompatible
Maker Renesas Electronics Corporation Renesas Electronics Corporation Renesas Electronics Corporation Renesas Electronics Corporation Renesas Electronics Corporation Renesas Electronics Corporation
Parts packaging code SOIC SOIC SOIC SOIC SOIC SOIC
package instruction SOP, SOP16,.25 SOP, SOP20,.4 SOIC-20 SOIC-20 SOP, SOP16,.25 SOP, SOP16,.25
Contacts 16 20 20 20 16 16
Reach Compliance Code not_compliant compliant not_compliant not_compliant compliant not_compliant
ECCN code EAR99 EAR99 EAR99 EAR99 EAR99 EAR99
Analog Integrated Circuits - Other Types SWITCHING CONTROLLER SWITCHING CONTROLLER SWITCHING CONTROLLER SWITCHING CONTROLLER SWITCHING CONTROLLER SWITCHING CONTROLLER
control mode CURRENT/VOLTAGE-MODE CURRENT/VOLTAGE-MODE CURRENT/VOLTAGE-MODE CURRENT/VOLTAGE-MODE CURRENT/VOLTAGE-MODE CURRENT/VOLTAGE-MODE
Control Technology PULSE WIDTH MODULATION PULSE WIDTH MODULATION PULSE WIDTH MODULATION PULSE WIDTH MODULATION PULSE WIDTH MODULATION PULSE WIDTH MODULATION
Maximum input voltage 5.25 V 5.25 V 5.25 V 5.25 V 5.25 V 5.25 V
Minimum input voltage 4.75 V 4.75 V 4.75 V 4.75 V 4.75 V 4.75 V
Nominal input voltage 5 V 5 V 5 V 5 V 5 V 5 V
JESD-30 code R-PDSO-G16 R-PDSO-G20 R-PDSO-G20 R-PDSO-G20 R-PDSO-G16 R-PDSO-G16
JESD-609 code e0 e3 e0 e0 e3 e0
length 9.9 mm 12.8 mm 12.8 mm 12.8 mm 9.9 mm 9.9 mm
Humidity sensitivity level 1 3 1 1 3 1
Number of functions 1 1 1 1 1 1
Number of terminals 16 20 20 20 16 16
Maximum operating temperature 70 °C 70 °C 70 °C 70 °C 70 °C 70 °C
Package body material PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY PLASTIC/EPOXY
encapsulated code SOP SOP SOP SOP SOP SOP
Encapsulate equivalent code SOP16,.25 SOP20,.4 SOP20,.4 SOP20,.4 SOP16,.25 SOP16,.25
Package shape RECTANGULAR RECTANGULAR RECTANGULAR RECTANGULAR RECTANGULAR RECTANGULAR
Package form SMALL OUTLINE SMALL OUTLINE SMALL OUTLINE SMALL OUTLINE SMALL OUTLINE SMALL OUTLINE
Peak Reflow Temperature (Celsius) 240 260 240 240 260 240
Certification status Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified Not Qualified
Maximum seat height 1.75 mm 2.65 mm 2.65 mm 2.65 mm 1.75 mm 1.75 mm
surface mount YES YES YES YES YES YES
Switch configuration PHASE-SHIFT PHASE-SHIFT PHASE-SHIFT PHASE-SHIFT PHASE-SHIFT PHASE-SHIFT
Maximum switching frequency 1500 kHz 1500 kHz 1500 kHz 1500 kHz 1500 kHz 1500 kHz
Temperature level COMMERCIAL COMMERCIAL COMMERCIAL COMMERCIAL COMMERCIAL COMMERCIAL
Terminal surface Tin/Lead (Sn/Pb) Matte Tin (Sn) - annealed Tin/Lead (Sn/Pb) Tin/Lead (Sn/Pb) Matte Tin (Sn) - annealed Tin/Lead (Sn/Pb)
Terminal form GULL WING GULL WING GULL WING GULL WING GULL WING GULL WING
Terminal pitch 1.27 mm 1.27 mm 1.27 mm 1.27 mm 1.27 mm 1.27 mm
Terminal location DUAL DUAL DUAL DUAL DUAL DUAL
Maximum time at peak reflow temperature 30 30 NOT SPECIFIED 30 40 30
width 3.9 mm 7.5 mm 7.5 mm 7.5 mm 3.9 mm 3.9 mm
18 celebrities collectively denounce rogue software
18 celebrities collectively denounce rogue software· Wang Quanguo ·Mao Yiding · Wang Jiangmin · Tao Ran · Wang Dong · Hou Tao· Guo Quji· Zhou Hongyi· Chen Bo · Wu Shichun· Cao Jian · Huang Yongtao· Li...
feifei Talking
Can anyone help me find the PDF of the 10102A chip?
Can anyone help me find the PDF of 10102A chip? Thanks a lot! Please contact me on QQ: 645652168...
欧屠龙 FPGA/CPLD
18B20 program passed on 6F877, 18F1320, 18F1220
This is the 18B20 program that has been passed on 6F877, 18F1320, and 18F1220. The main problem with 18B20 is the delay. Once this is solved, everything can be passed. # include# define uch unsigned c...
eeleader MCU
USB HOST Technology in Car Driving Recorder
1. Introduction to USB bus USB (Universal Serial Bus) is a universal serial bus and a standard connection interface. When connecting with external USB slave structures and USB HOST, there is no need t...
frozenviolet Automotive Electronics
How to burn the program into the specified flash address?
I encountered a problem in the project: I need to put a variable into a specified flash address, that is, the absolute address of the flash. I checked the IAR compiler manual, and the example above sa...
mukden stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1146  2777  1985  2148  1774  24  56  40  44  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号