EEWORLDEEWORLDEEWORLD

Part Number

Search

09821

Description
Installation and Maintenance of ESD Mats
File Size254KB,4 Pages
ManufacturerETC2
Download Datasheet Compare View All

09821 Online Shopping

Suppliers Part Number Price MOQ In stock  
09821 - - View Buy Now

09821 Overview

Installation and Maintenance of ESD Mats

TECHNICAL BULLETIN TB-2000
Installation and
Maintenance of ESD Mats
Introduction
The purpose of an ESD worksurface is to aid in the prevention
of damage to ESD sensitive components and assemblies from
electrostatic discharge. An ESD worksurface provides protection in
the following two ways:
1. Providing an antistatic worksurface area that will limit static
electricity generation.
2. Removing the charge from a conductive object placed on the
worksurface.
A dissipative worksurface having a surface resistance of at
least 1 x 10E6, but less than 1 x 10E9 ohms is recommended
by worksurface standard ANSI/ESD S4.1. Dissipative materials
minimize the generation of static charges, and will dissipate a
charge slow enough so that a spark will not occur. Dissipative
materials are usually the preferred choice for bench top
worksurfaces.
Conductive materials are the quickest to remove a charge,
but they can also cause damage by discharging too rapidly.
Conductive materials are usually used as floor mats, which is
defined by ANSI/ESD S7.1 as less than 1 x 10E6 ohms.
Figure 2. Other ground cords.
09814
Made in the
United States of America
09817
Figure 3. 09814 with screw allows ground cord to be bolted to mat
to keep cord from disconnecting.
Common point grounds are designed to provide ground for
worksurface mats, wrist straps, and other items.
NOTE:
DO NOT DAISY CHAIN. Because of the high resistances
inherent to many types of protective surfaces, daisy chaining of
these materials can severely limit their ability to properly dissipate
and protect against static charges.
General Grounding Guidelines
1. ANSI/ESD S20.20 requires that all conductors in an ESD
protected area, including personnel, must be grounded.
2. The ESD ground must be tied directly to and at the same
potential as the building or “green wire” equipment ground.
3. Per ANSI/ESD S20.20, the ESD control program can in no
way replace or supercede any requirements for personnel
safety. Ground fault circuit interrupters (GFCI) and other safety
protection should be considered wherever personnel might
come into contact with electrical sources.
4. All electrical outlets should be verified for proper wiring
configuration, resistance or impedance and GFCI function when
the mat is installed and periodically thereafter.
COMMON POINT GROUND
Per ANSI/ESD S6.1, Grounding section 4.1.1 “Every element to be
grounded at an ESD protected station shall be connected to the
same common point ground.”
ESD Handbook ESD TR20.20 section 5.1.3 Basic Grounding
Requirements “The first step in ensuring that everything in an
EPA is at the same electrical potential is to ground all conductive
components of the work area (worksurfaces, people, equipment,
etc.) to the same electrical ground point. This point is called the
common point ground. The next step in completing the ground
circuit is to connect the common point ground to the equipment
ground (third wire, green).”
Common Point Grounds
A common point ground is defined by the grounding standard
ANSI/ESD S6.1, as:
1. A grounded device where two or more conductors are bonded.
2. A system or method for connecting two or more grounding
conductors to the same electrical potential.
Examples of common point grounds with ground cords are
illustrated below.
09835
WRONG!
RIGHT
09825
09837
09740
Figure 4. ESD mats should never be grounded in series, that is
daisy chained.
Figure 1. Typical common point grounds.
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178
DESCO EAST
- One Colgate Way,
Canton, MA 02021-1407 • (781) 821-8370 • Web Site:
Desco.com
TB-2000
March 2012 Page 1 of 4
© 2012 DESCO INDUSTRIES INC.
Employee Owned

09821 Related Products

09821 09740 09741 09814 09817 09825 09835 09837
Description Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats Installation and Maintenance of ESD Mats
CC2530 updates nodes in the network wirelessly via Zigee, the protocol is adhoc
Through one node zigee to remotely update the program to another node, the program data is sent in the air with decryption. After the other node writes the backup FLASH, it needs to be sent back, and ...
machong RF/Wirelessly
Class D amplifiers mature
[p=null, 2, left][color=rgb(51, 51, 51)][font=Verdana, Helvetica, Arial, sans-serif]Over the past two to three years, designers have enhanced many end devices by adding new features, one of which is e...
qwqwqw2088 Analogue and Mixed Signal
Error between inductor and controlled current source during simulation
[font=宋体][size=4]Circuit: Multi-pulse Rectification[/size][/font] [font=宋体][size=4]Load: LCR Type Load[/size][/font] [font=宋体][size=4]Question: When simulating the LCR load in parallel with the contro...
hebaolee Power technology
How to make a good PCB board (transfer)
Everyone knows that making a PCB is to turn the designed schematic diagram into a real PCB circuit board. Please don't underestimate this process. There are many things that work in principle but are ...
呱呱 PCB Design
How to achieve more accurate uS or mS level delay when writing the underlying driver of wince?
For example, I want a GPIO to be set to a high level first, and then become a low level after 2uS....
sigon Embedded System
Methods for measuring insulation resistance of electric motors
[color=rgb(51, 51, 51)][backcolor=rgb(246, 246, 246)][font=微软雅黑][size=13px]Zhengneng ES3025E digital insulation resistance meter (5000V) has: range 0~200GΩ, minimum resolution 0.01MΩ, rated voltage: 2...
gzznele Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1469  1722  1449  565  2632  30  35  12  53  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号