09741 datasheet, PDF - EEWORLD Datasheet

09741: DescriptionInstallation and Maintenance of ESD Mats; File Size254KB，4 Pages; ManufacturerETC2

Download Datasheet Compare View All

09741 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	09741	-	-	View	Buy Now

09741 Overview

Installation and Maintenance of ESD Mats

Preview

Download Datasheet

View All

TECHNICAL BULLETIN TB-2000

Installation and

Maintenance of ESD Mats

Introduction

The purpose of an ESD worksurface is to aid in the prevention

of damage to ESD sensitive components and assemblies from

electrostatic discharge. An ESD worksurface provides protection in

the following two ways:

1. Providing an antistatic worksurface area that will limit static

electricity generation.

2. Removing the charge from a conductive object placed on the

worksurface.

A dissipative worksurface having a surface resistance of at

least 1 x 10E6, but less than 1 x 10E9 ohms is recommended

by worksurface standard ANSI/ESD S4.1. Dissipative materials

minimize the generation of static charges, and will dissipate a

charge slow enough so that a spark will not occur. Dissipative

materials are usually the preferred choice for bench top

worksurfaces.

Conductive materials are the quickest to remove a charge,

but they can also cause damage by discharging too rapidly.

Conductive materials are usually used as floor mats, which is

defined by ANSI/ESD S7.1 as less than 1 x 10E6 ohms.

Figure 2. Other ground cords.

09814

Made in the

United States of America

09817

Figure 3. 09814 with screw allows ground cord to be bolted to mat

to keep cord from disconnecting.

Common point grounds are designed to provide ground for

worksurface mats, wrist straps, and other items.

NOTE:

DO NOT DAISY CHAIN. Because of the high resistances

inherent to many types of protective surfaces, daisy chaining of

these materials can severely limit their ability to properly dissipate

and protect against static charges.

General Grounding Guidelines

1. ANSI/ESD S20.20 requires that all conductors in an ESD

protected area, including personnel, must be grounded.

2. The ESD ground must be tied directly to and at the same

potential as the building or “green wire” equipment ground.

3. Per ANSI/ESD S20.20, the ESD control program can in no

way replace or supercede any requirements for personnel

safety. Ground fault circuit interrupters (GFCI) and other safety

protection should be considered wherever personnel might

come into contact with electrical sources.

4. All electrical outlets should be verified for proper wiring

configuration, resistance or impedance and GFCI function when

the mat is installed and periodically thereafter.

COMMON POINT GROUND

Per ANSI/ESD S6.1, Grounding section 4.1.1 “Every element to be

grounded at an ESD protected station shall be connected to the

same common point ground.”

ESD Handbook ESD TR20.20 section 5.1.3 Basic Grounding

Requirements “The first step in ensuring that everything in an

EPA is at the same electrical potential is to ground all conductive

components of the work area (worksurfaces, people, equipment,

etc.) to the same electrical ground point. This point is called the

common point ground. The next step in completing the ground

circuit is to connect the common point ground to the equipment

ground (third wire, green).”

Common Point Grounds

A common point ground is defined by the grounding standard

ANSI/ESD S6.1, as:

1. A grounded device where two or more conductors are bonded.

2. A system or method for connecting two or more grounding

conductors to the same electrical potential.

Examples of common point grounds with ground cords are

illustrated below.

09835

WRONG!

RIGHT

09825

09837

09740

Figure 4. ESD mats should never be grounded in series, that is

daisy chained.

Figure 1. Typical common point grounds.

DESCO WEST

- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST

- One Colgate Way,

Canton, MA 02021-1407 • (781) 821-8370 • Web Site:

Desco.com

TB-2000

March 2012 Page 1 of 4

Employee Owned

09741 Related Products

	09741	09740	09814	09817	09821	09825	09835	09837
Description	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats	Installation and Maintenance of ESD Mats

Recommended Resources

Diode spark suppression circuit b

Delay light circuit using digital circuit (1)

Novel and practical AC electronic voltage regulator circuit

4-20MA－Convert to multiple 5V conversion circuit diagram

50KHZ bandwidth amplifier circuit

9V charger with digital circuit timer

FPGA image acquisition display help: Has anyone used FPGA to capture an image, store it in DDR, and then read it out continuously to display a still image on LCD? I have stored one now, but when I display it, the image always moves from ...; jokeboy999 FPGA/CPLD

The coordinator and the terminal device communicate in a single point. When the terminal device sends data every 20ms, the coordinator sends data to the terminal device.: [color=#000]I just came into contact with ZigBee, and encountered several problems when learning single-point communication. The terminal and the coordinator send data to each other, and the timer is ...; chuxuezhewy RF/Wirelessly

Intel's global semiconductor share hits a 10-year high of 15.6%: [i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:03[/i]Late on March 26, Beijing time, data from research firm IHS iSuppli showed that driven by demand in the PC processor market, Inte...; wstt Mobile and portable

TMS320DM8168/TMS320DM8148/TMS320DM8127/TMS320DM6437DM3730 Development Board: Based on TI Da Vinci series TMS320DM8168 floating-point DSP C674x + ARM Cortex-A8 high-performance video processorPowerful video encoding and decoding capabilities, with 3 independent programmable HD ...; fish001 DSP and ARM Processors

A collection of commonly used op amps: :victory: Commonly used operations...; kf_nyh Analog electronics

How to choose USB serial port chip: How to choose the USB serial port chip to be used on the development board...; 慕诗客 51mcu

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components