EEWORLDEEWORLDEEWORLD

Part Number

Search

SSCSHHN001PG2A5

Description
Total Error Band Amplified Compensated Digital Output, 1 psi to 150 psi 60mbar to 10 bar
File Size4MB,18 Pages
ManufacturerHoneywell
Websitehttp://www.ssec.honeywell.com/
Download Datasheet View All

SSCSHHN001PG2A5 Overview

Total Error Band Amplified Compensated Digital Output, 1 psi to 150 psi 60mbar to 10 bar

Installation Instructions for the
TruStability
®
Board Mount Pressure Sensors
Issue F
50044171
HSC Series—High Accuracy, Compensated/Amplified
±1.6 mbar to ±10 bar | ±160 Pa to ±1 MPa | ±0.5 inH
2
O to ±150 psi
Digital or Analog Output
SSC Series—Standard Accuracy, Compensated/Amplified
±1.6 mbar to ±10 bar | ±160 Pa to ±1 MPa | ±0.5 inH
2
O to ±150 psi
Digital or Analog Output
GENERAL INFORMATION
Honeywell’s TruStability
®
High Accuracy Silicon Ceramic (HSC)
Series and Standard Accuracy Silicon Ceramic (SSC) Series are
piezoresistive silicon pressure sensors offering a digital or analog
output for reading pressure over the specified full scale pressure
span and temperature range.
These sensors measure absolute, gage, or differential pressures.
The absolute versions have an internal vacuum reference and an
output value proportional to absolute pressure. Gage versions
are referenced to atmospheric pressure and provide an output
proportional to pressure variations from atmosphere. Differential
versions allow measurement of pressure between the two
pressure ports.
The HSC Series is calibrated over the temperature range of 0 °C
to 50 °C [32 °F to 122 °F] while the SSC Series is calibrated over
the temperature range of -20 °C to 85 °C [-4 °F to 185 °F].
The TruStability
®
pressure sensors are intended for use with
non-corrosive, non-ionic gases, such as air and other dry gases.
An available option extends the performance of these sensors to
non-corrosive, non-ionic liquids for pressure ranges above
40 mbar | 4 kPa | 20 inH
2
0.
CLEANING
CAUTION
IMPROPER CLEANING
Avoid cleaning the sensor; however, if it must be cleaned
ensure cleaning fluids, such as appropriate alcohols
or fluorinated solvents, are used based on the type of
contaminants to be removed. Do not immerse the sensor.
Failure to comply with these instructions may result in
product damage.
Table 1. Absolute Maximum Ratings
1
Min.
Max.
Unit
Characteristic
2
Supply voltage (V
supply
)
:
-3.0
6.0
Vdc
Storage temperature
-40 [-40] 85 [185] °C [°F]
Soldering time and temperature:
lead solder temperature (SIP, DIP) 4 s max. at 250 °C [482 °F]
peak reflow temperature (SMT)
15 s max. at 250 °C [482 °F]
1
CAUTION
PRODUCT DAMAGE FOR SENSORS WITH LIQUID MEDIA
OPTION (ONLY AVAILABLE 60 MBAR | 6 KPA | 1 PSI AND
ABOVE)
• Ensure liquid media is applied to Port 1 only; Port 2 is not
compatible with liquids.
• Ensure liquid media contains no particulates. All TruStability
®
sensors are dead-ended devices. Particulates can
accumulate inside the sensor, causing damage or affecting
sensor output.
• Recommend that the sensor be positioned with Port 1 facing
downwards; any particulates in the system are less likely
to enter and settle within the pressure sensor if it is in this
position.
• Ensure liquid media does not create a residue when dried;
build-up inside the sensor may affect sensor output.
Rinsing of a dead-ended sensor is difficult and has limited
effectiveness for removing residue.
• Ensure liquid media are compatible with wetted materials.
Noncompatible liquid media will degrade sensor
performance and may lead to sensor failure.
Failure to comply with these instructions may result in
product damage.
Absolute maximum ratings are the extreme limits the device will with-
stand without damage.
Incorrect application of supply voltage or ground to the wrong pin may
cause electrical failure.
2
CS5460 single-phase bidirectional power-energy IC
A well-designed LC oscillation circuit is not as stable as the frequency of the CRYSTA crystal oscillation circuit , but the CRYSTAL crystal oscillation cannot change the frequency at any time . In th...
rain Test/Measurement
Looking for the program that comes with CC2650 LaunchPad
I re-burned the CC2650 program a few days ago. Today I finally installed the simplelink starter on my phone and wanted to try the factory demo, but I can't find the hex. Please provide it....
woody_chen Wireless Connectivity
The leakage current of the adc pin of stm32
I searched the data sheet but couldn't find the leakage current of the ADC pin.I use cr2302 as the power supply for RTC. I usually measure the power. When the voltage is low, an alarm will be issued t...
lcllcl20031 stm32/stm8
Showing the WEBENCH design process + LM5009A wide range power supply design
To design a wide range power supply with 10-60V input and 5V output, we first select the LM5009A chip, which can be used for design. First, open WEBENCH and select the power design component list.Ente...
闲云潭影 Analogue and Mixed Signal
Core Route FPGA Tutorial Manual V1.09. A collection of Xiao Meige's writings. This guide focuses on various development experiences and operations, suitable for...
[font=新宋体][size=18.018px][size=6][color=red]Important things should be said three times: [/color][/size][/size][/font] [align=center][size=18.018px][font=新宋体][size=6][color=darkorange]Reply to the pos...
小梅哥 FPGA/CPLD
Please help me, it's emergency! Waiting online
Computer Architecture and Structure! Use your knowledge of storage system design and analysis to describe and analyze the Pentium 4 cache and virtual storage mechanisms!...
samhesam Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 285  1277  1713  1097  2565  6  26  35  23  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号