Changsha is looking for an assistant engineer. Requirements: Proficient in using PCB board making software such as PORTEL, familiar with the MCU 51 AVR series. Familiar with C language. Strong hands-o...
Product Introduction:AVR AT STK500 programmer/entry-level learning development board is an AVR serial programmer developed by ATMEL. STK500 supports HVSP/HVPP/ISP (serial high voltage programming, par...
[font=微软雅黑][size=3] Given that the F7 core board has just arrived (mine is still in the hands of the scumbag courier), and the specific requirements have not been fully determined, the current discuss...
[i=s]This post was last edited by Pirates of the Caribbean on 2019-8-5 17:41[/i]Recently I saw an open source source code for dynamic display of QR codes on the same-sex communication website github. ...
f_mount(0, fs); res = f_open(fdst, "0:3333.txt", FA_CREATE_ALWAYS | FA_WRITE); Here res returns the error code of Assertion failed, res = f_write(fdst, buffer, 512, bw); Here res returns the error cod...
[i=s]This post was last edited by 1nnocent on 2021-5-17 11:25[/i]In school, people often asked what would happen if a resistor was not connected in parallel to the ground at the non-inverting input of...
At present, the development of wireless power supply technology for electric vehicles (EVs) is becoming more and more active. In 2012, Volvo of Sweden established Volvo Technology Japan in Tokyo as...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Automotive applications are particularly sensitive to EMI events, which are unavoidable in a noisy electrical environment consisting of a central battery, bundled wiring harnesses, various inductiv...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
In order to highlight the concept of "energy saving and environmental protection" of intelligent buildings, solar street lights are designed for intelligent communities. The inclination and capacit...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Although it is relatively easy to check the stability of a simple amplifier at lower frequencies, it may be much more difficult to evaluate the stability of a more complex circuit. This artic...[Details]