Schmitt Octal Bus Transceiver with Three-State Outputs
Datasheet
November 2010
www.aeroflex.com/logic
FEATURES
Three-state outputs drive bus line directly
1.2μ
CMOS
- Latchup immune
High speed
Low power consumption
Single 5 volt supply
Available QML Q or V processes
Flexible package
- 20-pin DIP
- 20-lead flatpack
UT54ACS245S - SMD 5962-96572
DESCRIPTION
The UT54ACS245S is a non-inverting octal bus transceiver with
Schmitt Trigger input levels. The circuit is designed for asyn-
chronous two-way communication between data buses. The
control function implementation minimizes external timing re-
quirements.
The device allows data transmission from the A bus to the B bus
or from the B bus to the A bus depending upon the logic level
at the direction control (DIR) input. The enable input (G) dis-
ables the device so that the buses are effectively isolated.
The device is characterized over full military temperature range
of -55°C to +125°C.
FUNCTION TABLE
ENABLE
G
L
L
H
DIRECTION
CONTROL DIR
L
H
X
OPERATION
B Data To A Bus
A Data To B Bus
Isolation
PINOUTS
20-Pin DIP
Top View
DIR
A1
A2
A3
A4
A5
A6
A7
A8
V
SS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
DD
G
B1
B2
B3
B4
B5
B6
B7
B8
20-Lead Flatpack
Top View
DIR
A1
A2
A3
A4
A5
A6
A7
A8
V
SS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
DD
G
B1
B2
B3
B4
B5
B6
B7
B8
LOGIC SYMBOL
G
DIR
(19)
(1)
G3
3 EN1 (BA)
3 EN2 (AB)
(18)
1
2
(17)
(16)
(15)
(14)
B1
B2
B3
B4
A1
A2
A3
A4
A5
A6
A7
A8
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
B5
(13)
B6
(12)
B7
(11)
B8
1
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and IEC
Publication 617-12.
LOGIC DIAGRAM
DIR
(1)
(19)
G
A1
(2)
(18)
B1
A2
(3)
(17)
B2
A3
(4)
(16)
B3
A4
(5)
(15)
B4
A5
(6)
(14)
B5
A6
(7)
(13)
B6
A7
(8)
(12)
B7
A8
(9)
(11)
B8
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
3
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
T
+
V
T
-
V
H
PARAMETER
Schmitt Trigger, positive going threshold
1
ACS
Schmitt Trigger, negative going threshold
1
ACS
Schmitt Trigger, typical range of hysteresis
2
CONDITION
MIN
MAX
.7V
DD
UNIT
V
V
.3V
DD
ACS
I
IN
V
OL
V
OH
I
OL
Input leakage current
ACS
Low-level output voltage
3
ACS
High-level output voltage
3
ACS
Output current (Sink)
10
V
IN
= V
DD
or V
SS
I
OL
= 100μA
I
OH
= -100μA
V
IN
=V
DD
or V
SS
V
OL
=0.4V
I
OH
Output current (Source)
10
V
IN
=V
DD
or V
SS
V
OH
=V
DD
- 0.4
I
OZ
I
OS
P
total
I
DDQ
C
IN
C
OUT
Three-state output leakage current
Short-circuit output current
2, 4
ACS
Power dissipation
2, 8, 9
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
V
O
= V
DD
and V
SS
V
O
= V
DD
and V
SS
C
L
= 50pF
V
DD
= 5.5V
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
0.6
-1
1.5
1
V
μA
0.25
V
V
DD
- 0.25
12
V
mA
-12
mA
-30
30
μA
-300
300
2.0
10
15
15
mA
mW/
MHz
μA
pF
pF
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit, but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4.Not more than one output may be shorted at a time for maximum duration of one second.
5.Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10.Guaranteed based on characterization data, but not tested.
If any friends in the forum want to learn IoT technology and need IoT kits, they can take a look at my shop. I have been engaged in IoT work for a long time. I used to be the moderator of the RF secti...
[Recruitment] Part-time author of introductory books on assembly language
Our company is a well-known IT book planning and publishing company in the industry. We are currently working on a book on ass...
Today I was looking at the performance parameters of a sensor and saw two parameters, bandwidth and sensor resonant frequency. What aspects of the sensor's performance do these two parameters describe...
I just started to learn CC2420. I bought a development board and installed IAR software and ZIGBEE2007 protocol stack. But I don't know how to start learning, how to be more efficient and avoid detour...
I have studied G2XX chips for a while, and wrote a wireless transparent transmission program based on G2553 and CC1100E. The test results are pretty good. I upload it to share. The serial port and RF ...
[size=3]The second phase of the Honor Roll event has come to an end, and the list of winners is as follows: [/size][size=3] [b][color=#ff0000]Monthly Star[/color][/b][color=#ff0000]: [/color]Vacant (N...
Dual-mode inverters can operate both in conjunction with the grid and independently. These inverters can inject excess energy from renewable energy and storage devices into the grid, and withdraw p...[Details]
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
Electric motors and internal combustion engines of the same power have similar torque levels. High power requires high torque, and torque determines a vehicle's acceleration speed, commonly known a...[Details]
summary
There are multiple approaches to making industrial systems more intelligent, including applying artificial intelligence (AI) technology at the edge and in the cloud to sensor...[Details]
1. Introduction
Electronic scales are gradually replacing traditional measuring tools like springs and balances in everyday life, such as electronic price computing scales and electronic weigh...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Electric vehicles are becoming increasingly popular, with increasingly longer ranges. There are two ways to charge electric vehicles: slow charging and fast charging. Which is the most suitable? Sl...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
According to Nikkei, Japan has performed poorly in responding to China's power semiconductor challenges.
There are five major companies in Japan's power chip market: Mitsubishi Electric,...[Details]
With the advancement of science and technology and the promotion of green, energy-saving, and circular development, the demand for precise control and accurate measurement is increasing. In the pow...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
Consumer demand for premium listening experiences has driven rapid evolution in the wireless headphone market in recent years. Hybrid designs, which utilize two drivers per earbud to enhance sound ...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
