EEWORLDEEWORLDEEWORLD

Part Number

Search

BZV03/D0110/82

Description
Mains Power Connector, 1A, 250VAC, Male
CategoryThe connector    The connector   
File Size79KB,1 Pages
ManufacturerBULGIN
Websitehttp://www.bulgin.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

BZV03/D0110/82 Overview

Mains Power Connector, 1A, 250VAC, Male

BZV03/D0110/82 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerBULGIN
Reach Compliance Codecompliant
Connector typeMAINS POWER CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderMALE
Contact materialNOT SPECIFIED
Coupling typeSNAP
DIN complianceNO
IEC complianceNO
MIL complianceNO
Power Connector Ratings1A, 250VAC
Manufacturer's serial numberBZV
Installation typePANEL
Total number of contacts3
2009 China Wireless Portal DIY Competition
2009 China Wireless Portal National DIY Contest This article address: [url]http://www.anywlan.com/bbs/thread-26644-1-1.html[/url] Planning: [url=http://bbs.anywlan.com/]China Wireless Portal[/url] Thi...
tange RF/Wirelessly
Introduction to SPI NAND flash
[backcolor=rgb(222, 240, 251)] In the field of embedded systems, NOR flash and NAND flash, as storage devices, should be familiar to everyone. The interface of early NOR flash was in the form of paral...
13691982107 Medical Electronics
How to implement low voltage alarm (alarm below 12V)?
The microcontroller uses at89s52. I want to realize the low voltage alarm. The voltage in the car is about 12.8v after the engine is turned off. If you use electrical appliances without starting the c...
markov Embedded System
Wince 6.0 key press without interruption
wince 6.0 pxa270 1*1 key, connected in a matrix manner. No interrupt is generated when the key is pressed. Part of the code is as follows [code] XLLP_BOOL_T XllpKeyPadConfigure(XLLP_KEYPAD_REGS *v_pKe...
260658 Embedded System
Question: How much overhead does the STM32 function call have?
Platform: IAR5.30 ST-LINK Use 3IN1 board and STM32 FWLIB. The system works at 72MHz, initializes GPIO speed to 50MHz, and does not open any interrupts. while (1) { //GPIO_LED->BSRR = GPIO_Pin_6 | GPIO...
guoyaru123 stm32/stm8
DSP2812 full comparison PWM output problem
I use 2812 full comparison unit to generate PWM. Among them, PWM1, PWM3, and PWM5 output 1KHz, 40% duty cycle PWM waves, and PWM2, PWM4, and PWM6 output complementary waveforms. Now I find two problem...
xzyxtt DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2755  1259  757  469  291  56  26  16  10  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号