Reference Spec.No.JENF243A-9103H-01
Reference Only
P1/8
Chip Ferrite Bead BLM15□□□□□SH1D
Reference Specification [AEC-Q200]
1.Scope
This reference specification applies to Chip Ferrite Bead BLM15_SH series for Automotive Electronics
based on AEC-Q200.
2.Part Numbering
(ex.)
BL
M
15
AG
102
S
H
1
D
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(1)Product ID
(4)Characteristics
(7)Category(for Automotive Electronics)
(2)Type
(5)Typical Impedance at 100MHz (8)Numbers of Circuit
(3)Dimension (L×Ｗ) (6)Performance
(9)Packaging (D:Taping)
3.Rating
Impedance ()
(at 100MHz)(*1)
(refer to below comment)
Rated
Current
(mA)
DC Resistance
( max.)
(*1)
(refer to below
comment)
Initial
Values
Values After
Testing
0.05
0.10
0.15
0.20
0.25
0.35
0.35
0.45
0.60
0.70
1.0
1.1
0.08
0.15
0.10
0.15
0.20
0.30
0.35
0.45
0.40
0.50
0.55
0.65
0.80
0.90
0.60
0.70
0.65
0.75
0.90
1.0
1.4
1.5
Customer
Part Number
MURATA
Part Number
ESD Rank
2 :2kV
BLM15AG100SH1D
BLM15AG700SH1D
BLM15AG121SH1D
BLM15AG221SH1D
BLM15AG601SH1D
BLM15AG102SH1D
BLM15BB050SH1D
BLM15BB100SH1D
BLM15BB220SH1D
BLM15BB470SH1D
BLM15BB750SH1D
BLM15BB121SH1D
BLM15BB221SH1D
BLM15BD471SH1D
BLM15BD601SH1D
BLM15BD102SH1D
BLM15BD182SH1D
5½15
40½100
120±25%
220±25%
600±25%
1000±25%
5±25%
10±25%
22±25%
47±25%
75±25%
120±25%
220±25%
470±25%
600±25%
1000±25%
1800±25%
1000
500
500
300
300
200
500
300
300
300
300
300
200
200
200
200
200
2
■Operating
Temperature : -55°C to +125°C
(*1)
■Storage
Temperature : -55°C to +125°C
Standard Testing Conditions
Unless otherwise specified
Temperature : Ordinary Temp. (15
°C
to 35
°C
)
Humidity : Ordinary Humidity (25%(RH) to 85%(RH))
In case of doubt
Temperature : 20°C±2
°C
Humidity : 60%(RH) to 70%(RH)
Atmospheric pressure : 86kPa to 106kPa
4.Style and Dimensions
1.0±0.05
0.5±0.05
0.5±0.05
■
Equivalent Circuit
0.25±0.1
(
: Electrode
(in mm)
Resistance element becomes
dominant at high frequencies.
)
■
Unit Weight (Typical value)
0.001g
MURATA MFG.CO.,LTD.
Reference Spec.No.JENF243A-9103H-01
5.Marking
No marking.
Reference Only
P2/8
6.Specifications
6-1.Electrical Performance
No.
Item
6-1-1 Impedance
Specification
Meet item 3.
Test Method
Measuring Frequency : 100MHz±1MHz
Measuring Equipment : KEYSIGHT4291A or the equivalent
Test Fixture : KEYSIGHT16192A or the equivalent
Measuring Equipment : Digital multi meter
*Except resistance of the Substrate and Wire
6-1-2 DC Resistance
Meet item 3.
6-2.Mechanical Performance
(based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS)
AEC-Q200 Rev.D issued June. 1 2010
AEC-Q200
Stress
Test Method
No.
3 High
1000hours at 125 deg C
Temperature
Set for 24hours
Exposure
at room temperature,
then measured.
Murata Specification / Deviation
Meet Table A after testing.
Table A
Appearance No damage
Impedance
Change
Within ±30%
(at 100MHz)
DC
Meet item 3.
Resistance
Meet Table A after testing.
4
Temperature Cycling 1000cycles
-55 deg C to +125 deg C
Set for 24hours
at room temperature,
then measured.
Destructive
Physical Analysis
Biased Humidity
Per EIA469
No electrical tests
5
7
No defects
1000hours at 85 deg C, 85%RH Meet Table A after testing.
Apply max rated current.
MURATA MFG.CO.,LTD.
Reference Spec.No.JENF243A-9103H-01
AEC-Q200
Stress
No.
8 Operational Life
Reference Only
Murata Specification / Deviation
Meet Table A after testing.
If the rated current of parts exceed 1A,
the operating temperature should be 85 deg C.
No abnormalities
No defects
P3/8
Test Method
Apply 125 deg C 1000hours
Set for 24hours at
room temperature,
then measured
Visual inspection
Meet ITEM 4
（Style
and Dimensions）
Per MIL-STD-202 Method 215
9
External Visual
10 Physical Dimension
12 Resistance
to Solvents
13 Mechanical Shock
Not Applicable
Per MIL-STD-202 Method 213 Meet Table A after testing.
Condition F:
1500g's(14.7N)/0.5ms/Half sine
5g's(0.049N) for 20 minutes Meet Table A after testing.
12cycles each of 3 oritentations
Test from 10-2000Hz.
Solder temperature
260C+/-5 deg C
Immersion time 10s
Per AEC-Q200-002
Pre-heating: 150C +/-10 deg C, 60s to 90s
Meet Table A after testing.
ESD Rank: Meet Item 3 (Rating)
BLM15AG sereis: Meet Table A after testing.
BLM15BB/BD series: Meet Table B after testing.
Table B
Appearance
Impedance
Change
(at 100MHz)
DC
Resistance
No damage
Within ±40%
Meet item 3.
14 Vibration
15 Resistance
to Soldering Heat
17 ESD
18 Solderability
Per J-STD-002
Method b : Not Applicable
95% of the terminations is to be soldered.
No defects
19 Electrical
Characterization
20 Flammability
21 Board Flex
Measured : Impedance
Per UL-94
Epoxy-PCB(1.6mm)
Deflection 2mm(min)
60s minimum holding time
Per AEC-Q200-006
Not Applicable
Meet Table A after testing.
22 Terminal Strength
Murata deviation request: 5N
No defects
30 Electrical
Transient
Conduction
Per ISO-7637-2
Not Applicable
MURATA MFG.CO.,LTD.
Reference Spec.No.JENF243A-9103H-01
Reference Only
1.75±0.1
P4/8
7.Specification of Packaging
7-1.Appearance and Dimensions
(8mm-wide paper tape)
2.0±0.05
2.0±0.05 4.0±0.1
1.5
-0
+0.1
1.15(Typ.)
3.5±0.05
8.0±0.3
0.8max.
0.65(Typ.)
Direction of Feed
(in mm)
(1) Taping
Products shall be packaged in the cavity of the base tape of 8mm-wide, 2mm-pitch continuously and sealed
by top tape and bottom tape.
(2) Sprocket hole:Sprocket hole shall be located on the left hand side toward the direction of feed.
(3) Spliced point:The base tape and top tape have no spliced point
(4) Cavity:There shall not be burr in the cavity.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater, and are not
continuous. The specified quantity per reel is kept..
7-2.Tape Strength
(1)Pull Strength
Top tape
Bottom tape
5N min.
165 to 180 degree
F
Top tape
(2)Peeling off force of Cover tape
0.1N to 0.6N (Minimum value is typical.)
*Speed of Peeling off:300mm/min
Bottom tape
Base tape
7-3.Taping Condition
(1)Standard quantity per reel
Quantity per 180mm reel
10000 pcs. / reel
(2)There shall be leader-tape(top tape and empty tape) and trailer- tape(empty tape) as follows.
(3)On paper tape, the top tape and the base tape shall not be adhered at the tip of the empty leader tape
for more than 5 pitch.
(4)Marking for reel
The following items shall be marked on a label and the label is stuck on the reel.
(Customer part number, MURATA part number, Inspection number(1) , RoHS marking(2) , Quantity, etc)
1)
« Expression of Inspection No. »
□□
OOOO
(1)
(1)
Factory Code
(2)
Date
(3)
Serial No.
(2)
(3)
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep.
1 to 9, Oct. to Dec.
O,N,D
Third, Fourth digit : Day
ROHS – Y (△)
(1) (2)
2)
« Expression of RoHS marking »
(1)
RoHS regulation conformity parts.
(2)
MURATA classification number
(5)Outside package
These reels shall be packed in the corrugated cardboard package and the following items shall be marked
on a label and the label is stuck on the box.
(Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS marking(2) ,Quantity, etc)
MURATA MFG.CO.,LTD.
Reference Spec.No.JENF243A-9103H-01
Trailer
160 min.
Reference Only
Leader
P5/8
(6)Dimensions of reel and taping(leader-tape, trailer-tape)
2.0±0.5
Label
190 min.
Empty tape
210 min.
Top tape
13.0±0.2
+1
60
-
0
9.0
+1
-0
21.0±0.8
Direction of feed
13.0±1.4
180
-3
+0
(in mm)
7-4. Specification of Outer Case
Label
H
D
W
Outer Case Dimensions
Standard Reel Quantity in Outer Case
(mm)
(Reel)
W
D
H
186
186
93
5
Above
Outer Case size is typical. It is depend on a quantity of an
order.
8.
！
Caution
8-1.Rating
Do not use products beyond the Operating Temperature Range and Rated Current.
8-2.Surge current
Excessive surge current (pulse current or rush current) than specified rated current applied to the
product may cause a critical failure, such as an open circuit, burnout caused by excessive
temperature rise.
Please contact us in advance in case of applying the surge current.
8-3.Fail Safe
Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage
that may be caused by the abnormal function or the failure of our products.
8-4.Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1)Aircraft equipment
(6)Disaster prevention / crime prevention equipment
(2)Aerospace equipment
(7)Traffic signal equipment
(3)Undersea equipment
(8)Transportation equipment (trains, ships, etc.)
(4)Power plant control equipment
(9) Data-processing equipment
(5)Medical equipment
(10)Applications of similar complexity and /or reliability
requirements to the applications listed in the above
MURATA MFG.CO.,LTD.
京公网安备 11010802033920号
EEWORLD
