ABC2-FREQ-22-R150-Y-T datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> ABC2-FREQ-22-R150-Y-T

ABC2-FREQ-22-R150-Y-T: DescriptionParallel - Fundamental Quartz Crystal, 4MHz Min, 5.999MHz Max, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN; CategoryPassive components Crystal/resonator; File Size154KB，2 Pages; ManufacturerAbracon; Websitehttp://www.abracon.com/index.htm; Environmental Compliance

Download Datasheet Parametric View All

ABC2-FREQ-22-R150-Y-T Overview

Parallel - Fundamental Quartz Crystal, 4MHz Min, 5.999MHz Max, ROHS COMPLIANT, CERAMIC, SMD, 4 PIN

ABC2-FREQ-22-R150-Y-T Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	conform to
Maker	Abracon
package instruction	ROHS COMPLIANT, CERAMIC, SMD, 4 PIN
Reach Compliance Code	compliant
Other features	TAPE AND REEL
Ageing	5 PPM/FIRST YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	100 µW
frequency stability	0.003%
frequency tolerance	30 ppm
load capacitance	22 pF
Manufacturer's serial number	ABC2
Installation features	SURFACE MOUNT
Maximum operating frequency	5.999 MHz
Minimum operating frequency	4 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
physical size	L11.6XB3.8XH2.0 (mm)/L0.457XB0.15XH0.079 (inch)
Series resistance	150 Ω
surface mount	YES

Preview

Download Datasheet

View All

LOW FREQUENCY CERAMIC SURFACE MOUNT

MICROPROCESSOR CRYSTAL

ABC2

RoHS

Compliant

APPLICATIONS:

• Wide range in communication & measuring equipment

• Commercial & Industrial applications

• Automotive electronics applications

11.5 x 5.5 x 2.0 mm

| | | | | | | | | | | | | | |

FEATURES:

• Low frequency in small size SMD

• 2.0mm height ideal for high density circuit boards

• Ceramic package offers excellent environmental & heat resistance

• Extended temperature -40°C to +85°C for industrial applications

STANDARD SPECIFICATIONS:

PARAMETERS

ABRACON P/N

Frequency Range

Operation Mode

Operating Temperature

Storage Temperature

Frequency Tolerance at +25°C

Frequency Tolerance over the

Operating Temp. (-10°C to + 60°C)

Frequency Stability over the

Operating Temp. (Ref to +25° C)

Equivalent Series Resistance

Shunt Capacitance C0

Load Capacitance CL

Drive Level

Aging (first year) 25°C ± 3°C

Insulation Resistance

ABC2

3.500 MHz to 30.000 MHz

Fundamental, AT

-10°C to + 60°C (see options)

-55°C to +125°C

±30ppm

below 6.0MHz: ±50ppm

above 6.0MHz: ±30ppm

± 50ppm max. (see options)

See Table 1

7pF max

18pF (see options)

100 W max.

± 5 ppm max.

500 M

min. at 100 Vdc

±15V

TABLE 1

Frequency (MHz)

Temp-D

ESR

3.500 - 3.999

200 max ±150ppm max

4.000 - 5.999

150 max ±100ppm max

6.000 - 9.999

100 max ±80ppm max

10.00 - 13.99

80 max ±60ppm max

14.00 -30.00

50 max ±60ppm max

OPTIONS AND PART IDENTIFICATION:

(Left blank if standard)

ABC2 - Frequency -

-R

Load Capacitance

10pF

12pF

16pF

18pF

20pF

22pF

Operating Temp.

-20°C to +70°C

-40°C to +85°C

Packaging

Tape and

Reel

ESR

Please specify ESR in

ohms. (RXXX)

ABRACON IS

ISO 9001 / QS 9000

CERTIFIED

Freq. Stability

± 25 ppm

± 30 ppm (*)

± 50 ppm (**)

± 100 ppm

(*) Standard for above 6.0MHz

(**) Standard for below 6.0MHz

REVISED: 4.05.07

30332 Esperanza, Rancho Santa Margarita, California 92688

tel 949-546-8000

fax 949-546-8001

| www.abracon.com

Recommended Resources

Internal block diagram of PS501

Commonly used low pass filter circuit c

SAA1064 serial I2C bus LED dynamic driver interface circuit diagram

Motor control circuit that can send start signal

Airmate TW-HT202 heater circuit diagram

Cycle counter display

Save and restore BIOS parameters: Save and restore BIOS parameters The so-called system settings refer to the hardware device information that users can select and install. Usually, it must be recorded in some form so that when the sy...; wo2000ailuo PCB Design

Why does 2450 eboot crash when downloading NK DNW0.6 over 40M?: As the title says. It is normal to download NK of more than 20M. If I download 40M, the progress bar of DNW will stop after two-thirds of the download. Here are some printed information: _OEMPlatformI...; zhanghuiyang Embedded System

[FPGA warning message] No load capacitance is specified for output management: Warning: Found xx output pins without output pin load capacitance assignment Reason: No load capacitance is assigned to the output pin Solution: This function is used to estimate TCO and power consump...; eeleader FPGA/CPLD

About LVDS Levels in FPGA: I use AD9230, which outputs LVDS level. I connect its data to FPGA. For example, the AD data line is: AD0+ to AD12+ and AD0- to AD12-. How to process this data in FPGA? Is it to subtract the positive ...; dahaotile FPGA/CPLD

Timer A in ADC is used as sampling trigger source: Why can't I enter the ADC interrupt when using timer A as the trigger source?#includemsp430x14x.h #define M 4 static unsigned int index = 0 ;unsigned int results[M]; void ADC12_Init ( void ) ;void UAR...; Lucky_Hu Microcontroller MCU

There are a lot of problems with vxworks, please give me some advice!!! Let's communicate more!!! Thank you!!!: I have encountered many problems recently. Please help me! ! I am using an embedded VxWorks system based on the G4 platform. The chip is ppc 7447A and vxworks5.5.1. 1. A very strange phenomenon: after...; lnx Real-time operating system RTOS

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components