PH1-GLHLA3325 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-GLHLA3325

PH1-GLHLA3325: DescriptionTransponder, 10000Mbps(Tx), 10000Mbps(Rx), LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-GLHLA3325 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), LC/SPC Connector,

PH1-GLHLA3325 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Connection Type	LC/SPC CONNECTOR
Data rate (receive)	10000 Mbps
Data rate (send)	10000 Mbps
Emitter/Detector Type	AVALANCHE PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1543 nm
Nominal optical power output	2.511 mW
minimum return loss	-27 dB
Sensitivity	-24 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

One of the time relay control motor timing forward and reverse circuits

Application circuit of TDA2040(A)-dual power supply operation

TL431 forms a series voltage regulator circuit

LT1121-5 typical application diagram

Tuning indication circuit

The most practical basic diagram circuit 60 - water pump start and stop control circuit

[Leisure] Top 10 Strange Pictures - See how the eyes deceive the brain: Top 10 Weird Pictures - How the Eyes Tricker the BrainIs the pillar round or square? Look carefully at the photo, there is a lion's head! It is said that people who can see 9 faces have an IQ of 180 a...; SuperStar515 Talking

SAMD21 development board trial experience + avrstudio 6.2 debugging SAMD21 Xplained pro + Example 1-led lighting program: [i=s] This post was last edited by xinxiaojun on 2014-9-30 20:15 [/i] [size=5]SAMD21 development board trial experience + avrstudio 6.2 debugging SAMD21 Xplained pro development board 1-led lighting p...; xinxiaojun MCU

I have a question here while testing a full-bridge LLC+SR synchronous rectification circuit?: When testing the Vds waveform of the MOS tube of the SR synchronous rectification, I zoomed in on the oscilloscope cycle. Why are there peaks and valleys? Isn't it just a high and low square wave wave...; 西里古1992 Power technology

LPC1769 has no place to run the program: The situation is as follows: As a rookie, I don't know much about chips. I connected the 4V signal P2[10] to the external interrupt 1. It was able to run at first, but after a while, the above situati...; minghui2009 NXP MCU

Can the LPC11 serial C program in Keil specify the absolute address of variables/functions? How to specify it?: :carnation: I know KEIL C51 is OK.This is used to develop programs in several parts or to patch them.[[i]This post was last edited by oayzw on 2012-7-19 09:08[/i]]...; oayzw NXP MCU

Help: In CCS, the point stops running, but PWM still has output?: The problem with CCS version 3.3is as follows:the program is running in RAM. After loading the program, click Run, and it runs normally, and PWM has output.However, after clicking Halt, CCS shows that...; laoqiao Microcontroller MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components