45 Mb/s to 2.7 Gb/s Optical 2R Receiver Module with FSK
Tone Detection Option
54RM Series
Key Features
• MSA compliant
• Frequency Shift Keying (FSK) tone detection option allows
control and status monitoring of the network
• 1310 nm or 1550 nm operation
• Data rates from 45 Mb/s to 2.7 Gb/s (no CDR)
• APD for better than -30 dBm sensitivity
• -40 °C to 85 °C operation
• Decision threshold voltage adjustment provided for use in
amplified system
Applications
• High speed, long haul fiberoptic links
for voice, data, and digital video
• Metropolitan area networks
• Wide area networks
The JDSU 54RM 2R series receiver module is designed for use in
telecommunications systems and high speed data communications applications.
This flexible device incorporates Frequency Shift Keying (FSK) tone detection.
When used with the companion FSK transmitter, the 54RM provides control and
status of a network with no additional fiber required. Its uniform package, pin
function, and common optical and electrical characteristics are Multisource
Agreement (MSA) compliant.
The 54RM 2R receiver module design uses an Indium Gallium Arsenide (InGaAs)
Avalanche photodiode (APD) detector. It does not include a Clock/Data Recovery
(CDR) function, thus allowing additional system design flexibility. It contains an
integrated APD high voltage supply that is temperature-compensated at our
factory for optimum sensitivity.
The 54RM 2R receiver module operates at continuous rates from 45 Mb/s to 2.7 Gb/s
without gap and provides options for current mode logic (CML) or LVPECL
outputs. The 54RM receiver also features an optical input level voltage (OILV)
monitor with ±1dB accuracy and decision threshold voltage (DTV) adjustment.
Compliance
• Telcordia GR-253-CORE
• ITU-T G.958
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
45 MB/S TO 2.7 GB/S OPTICAL 2R RECEIVER MODULE
WITH FSK TONE DETECTION OPTION
2
Dimensions Diagram
(Specifications in inches [mm] unless otherwise noted.)
2.307
[58.6]
54RM-WXYZ
2.5 Gb/s Receiver
1.000
[25.4]
1.402
[35.6]
39.00±3.9
[990.6±.99]
R1.18 MIN
[R30 MIN]
• PIN 1
Made in USA
0.201
[5.1]
0.362
[9.2]
0.100 TYP
[2.54]
0.012
0.500
[12.7]
[0.3]
0.018 TYP
[0.46]
Note: FC optical connectors are shown for illustration only.
Pinout
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Symbol
FSK
NUC
LPA
GND
NIC
NIC
GND
VCC
GND
Dout
Dout
GND
DTV
GND
GND
GND
GND
NIC
GND
GND
NUC
VCC
OILV
NUC
Description
FSK output
No user connection
Loss of power alarm (LOS)
1
Ground
2
No internal connection
No internal connection
Ground
2
Supply voltage (5 V)
Ground
2
Data positive output
Data negative output
Ground
2
Decision threshold voltage
Ground
2
Ground
2
Ground
2
Ground
2
No internal connection
Ground
2
Ground
2
No user connection
Supply voltage (5 V)
Optical input level voltage
No user connection
1. LPA output is a logic level that indicates the presence or absence of a
sufficient optical input level. A logical high level indicates an input
optical level that is too low.
2. Package is at the same potential as GND.
45 MB/S TO 2.7 GB/S OPTICAL 2R RECEIVER MODULE
WITH FSK TONE DETECTION OPTION
3
Optical Incoming Signal and the Envelope Signal
Optical
Input
Power
Eye pattern of SONET,
GE, etc.
t
f1
Envelope
Output
Voltage
f2
f1
t
Note: The envelope signal is a FSK signal. It is a sine wave that contains two frequencies [f1 and f2, where f2 - f1 = 14.3 KHz (max.), and 50 KHz < f1, f2 <500 KHz].
Characteristics of Envelope Detector
Parameter
Output AC voltage signal (note
1
)
Low cut-off frequency (-1 dB)
Low cut-off frequency (-20 dB)
High cut-off frequency (-1 dB) (note
1
)
High cut-off frequency (-20 dB) (note
1,2
)
Clipping and distortion (note
3
)
S/N in a 40 KHz bandwidth (note
4
)
Spurious level (note
5
)
Symbol
Venv
Minimum
5 mVp-p
-42 dBm
-
15 KHz
500 KHz
-
-
14 dB
-
Typical
-
-
-
-
-
-
-
-
-
Maximum
632 mVp-p
0 dBm
50 KHz
-
-
4000 KHz
10 %
-
6 dB above noise floor
1. Incoming optical signal with power in the range of -32 dBm to -7 dBm and modulation depth of 5% to 10% (dBm values assume a single tone, not random data with two
tones for FSK channel).
2. The gain at frequencies below the Low cut-off frequency (-20 dB) and above the High cut-off frequency (-20 dB) must be smaller than -20 dB.
3. The envelope-detected signal should not be clipped to the extent the FSK signal-to-noise ratio goes below 14 dB in a 40 KHz bandwidth with an optical input of -7 dBm
and modulation index of 10%.
4. The measurement is conducted at two frequencies: one centered at 80 KHz and the other at 180 KHz. In addition, the measurements are performed at:
a. Carrier data rate of 622 MHz and PRBS 223-1 data pattern with total power into the receiver of -32 dBm and 10% modulation index
b. Carrier data rate of 2488 MHz and PRBS 223-1 data pattern with total power into the receiver of -32 dBm and 5% modulation index
5. Spurs measured with OC 48, PRBS 223-1 signal input and measured between:
a. 55 KHz and 105 KHz
b. 155 KHz and 205 KHz
at a resolution bandwidth of 3 KHz.
45 MB/S TO 2.7 GB/S OPTICAL 2R RECEIVER MODULE
WITH FSK TONE DETECTION OPTION
4
Electrical Specifications
Parameter
Positive supply voltage
APD HV supply
Power consumption (total)
Differential output data voltage (LVPECL) (note
1
)
Output rise time (20% to 80%)
Output fall time (80% to 20%)
Output data return loss
1 MHz to 2 GHz
2 GHz to 2.5 GHz
Loss of power alarm output level
Normal signal input
Low signal input (alarm)
"Low Light" alarm assert time
"Low Light" alarm de-assert time
Optical input level (pin 23) at 1550 nm (note
2
)
Optical input = -40 dBm (±2 dB)
Optical input = -30 dBm (±1 dB)
Optical input = -20 dBm (±1 dB)
Optical input = -10 dBm (±1 dB)
Optical input = -5 dBm
Full scale range
Slope
Decision threshold voltage (pin 13)
input voltage range (note
3
)
Data, load drive capability
Jitter generation
Jitter tolerance (note
4
)
Jitter transfer (note
4
)
Logic output level
1. Must be externally AC coupled and externally loaded by 50
Ω.
Symbol
Vcc
Minimum
4.75 V
Internal
-
0.55 V
p-p
-
-
9 dB
6 dB
0V
Vcc - 0.4 V
-
-
0.45 V
0.95 V
1.45 V
1.95 V
-
-5 dBm
-
0.5 V
-
Typical
5V
1.2 W
-
130 ps
130 ps
-
-
-
-
-
-
0.5 V
1.0 V
1.5 V
2.0 V
2.25 V
-
50 mV/dB
-
Maximum
5.25 V
1.5 W
1.2 V
p-p
150 ps
150 ps
-
-
0.4 V
Vcc
1 ms
1 ms
0.55 V
1.05 V
1.55 V
2.05 V
-
-40 dBm
-
3.5 V
Tr
Tf
RL
RL
LPA
Llite
T(aa)
T(a0)
OIL
DTV
RL
50
Ω
-
Meets GR-253/ITU-T G.958
Meets GR-253/ITU-T G.958
Meets GR-253/ITU-T G.958
TTL compatible
2. The OILV output is tested and tuned using a 1550 nm optical input. When a 1310 nm source is present, the OILV output may vary by ±2 dB since there may be an offset associated
with receiving a 1310 nm optical signal as compared to 1550 nm. However, typically most modules will exhibit a small variation between 1310 nm and 1550 nm inputs.
3. By varying the DTV voltage at pin 13 from 0.5 VDC to 3.5 VDC the quanitization threshold level is shifted from the bottom of the data eye to the top of the data eye respectively.
Threshold adjustment without optical noise (V
optimum
) is symmetric about 2.0 VDC. At DTV set points of 0.5 VDC and 3.5 VDC, the BER will be shifted to a typical
value of 10 E-7 from a nominal BER of 10 E-10 (i.e. no input applied at DTV). If the DTV function is not required, pin 13 should be left open. An extended DTV full-
scale input range of 0.0 V to 5.0 V may be used if additional threshold adjustment range is required.
4. This requirement is only applicable when used with a CDR, which meets the given jitter tolerance and jitter transfer specifications.
45 MB/S TO 2.7 GB/S OPTICAL 2R RECEIVER MODULE
WITH FSK TONE DETECTION OPTION
5
Typical DTV Adjustment Range
‘0’ to “1’ Increasing Errors
‘1’ to “0’ Increasing Errors
1E-7
BER
1E-10
0.5
2.0
V
optimum
DTV (VDC)
3.5
Note: Curve shown without optical noise.
Typical V
optimum
with optical noise is 1.75 VDC.
Optical Specifications
Parameter
Symbol
54RM-4xxx
1310 nm or 1550 nm
2R (APD, No CDR)
1260 nm
1618 nm
-29 dBm
-31 dBm
-30 dBm
-32.5 dBm
-23 dBm
-26 dBm
-8 dBm
-7 dBm
-28 dB
-27 dB
-40 dBm
-34 dBm
0.5 dB
2 dB
54RM-5xxx
1310 nm or 1550 nm
2R (PIN, No CDR)
1260 nm
1615 nm
-19 dBm
-20 dBm
- 20 dBm
- 21 dBm
-15 dBm
-17 dBm
0 dBm
1 dBm
-28 dB
-27 dB
-22 dBm
-30 dBm
0.5 dB
2 dB
ITU-T / SONET
Center wavelength
Receiver sensitivity (note
1, 2
)
Receiver sensitivity 45 MHz to GE (note
1, 2
)
Receiver sensitivity with noise and path penalty (note
3
)
Receiver overload
Maximum reflectance
LPA flag threshold
LPA hysteresis
λ
C
Psens
Povld
Minimum
Maximum
Minimum
Typical
Minimum
Typical
Minimum
Typical
Minimum
Typical
Typical
Maximum
Minimum
Maximum
Minimum
Maximum
1. Measured at BER 10
-10
and at the connector interface with conditions at EOL with an 8.2±0.1 dB extinction ratio optical source. The receiver shall exhibit a BER slope less
than -0.5 dB per BER decade down to a BER of 10
-14
. When using the FSK option, the sensitivity will be degraded by 0.5 dB.
2. Receiver sensitivity is valid for data rates from 45 Mb/s to 2.7 Gb/s. For data rates from 45 Mb/s up to 155 Mb/s the PRBS pattern is 2
7
-1, and for data rates from 155 Mb/s
to 2.7 Gb/s the PRBS pattern is 2
23
-1.
3. Measured at BER 10
-12
, OSNR 0.1 nm = 19 dB through 0.8 nm optical filter (square shape equivalent filter) and STM-16 PRBS 2
23
- 1 signal with a CDR (ITU-T G.958)
and an MSA transmitter with 3200 ps/nm optical path. DTV (pin 13) set to V
Without further ado, let's get to the point. Hide when it's time to hide, and show when it's time to show. Method 1: ShowCrusor() but ce doesn't support it. Give up method 2: Use SetCrusor() to replac...
Common Control 3Bit[7]:ReservedBit[6]:Output data MSB and LSB swapBit[5:4]: ReservedBit[3]:Pin selection
0C COM3 00 RW1: Change RESET pin to EXPST_B (frame exposuremode timing) and change PWDN pin to ...
My ICD2 is very strange. Some time ago, I saw a post online that said that if I set the clock in configure to XT and turn off everything else, I could enter debug mode. But yesterday, I followed the s...
This experiment uses the Zero-Knowledge ESP8266 and rc-switch modules.1. Experimental materialsZero-Knowledge ESP8266 development boardR433s transceiver and transmitter modulesSeveral Dupont cables
2....
When using 149 to do AD experiment, I can't adjust it no matter what. After jtag debugging, I found that ADC12SC is not set, that is, the ADC12 core is not started. ENC and other bits are already set....
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
A parallel inverter consists of two thyristors (T1 and T2), a capacitor, a center-tapped transformer, and an inductor. The thyristors provide a current path, while the inductor L maintains a consta...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
In recent years, many people have switched to new energy vehicles, and this type of vehicle has indeed been highly sought after and is considered the future direction of automobile development, and...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
On August 21, WeRide officially launched WePilot AiDrive, a one-stage end-to-end assisted driving solution developed in cooperation with Bosch. This comes only half a year after the two parties' "t...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Industrial computers with GPUs leverage powerful parallel processing to build deep learning models to analyze and respond to optical inputs. The systems develop an understanding of visual data to i...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
According to Nikkei, a survey found that global electric vehicle battery supply is expected to reach more than three times the required quantity due to
cooling
demand for electric vehicles,...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
