Measurement at same location as “Initial breakdown voltage” section.
1,000 Vrms for 1min. (Detection current: 10mA.)
2,000 Vrms (1 Form A 1 Form B, 2 Form A) (Detection current: 10mA.)
3,000 Vrms for 1min. (Detection current: 10mA.)
5,000 V
Max. 55°C
Max. 40°C
Max. 55°C
Max. 10 ms [10 ms] (Nominal voltage applied to the coil, excluding contact bounce time.)
Max. 5 ms [10 ms] (Nominal voltage applied to the coil, excluding contact bounce time.)
(without diode)
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
Min. 196 m/s
Min. 980 m/s
2
(Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 2 mm (Detection time: 10
µs.)
10 to 55 Hz at double amplitude of 3.5 mm
Min. 5×10
7
(at 180 cpm)
Min. 10
5
(resistive load)
Ambient temperature:
Ambient temperature:
Ambient temperature:
–40°C to +60°C
–40°C to +65°C
–40°C to +60°C
–40°F to +140°F
–40°F to +149°F
–40°F to +140°F
250°C
482°F
(10s), 300°C
572°F
(5s), 350°C
662°F
(3s)
(Soldering depth: 2/3 terminal pitch)
3 cps
Approx. 4.5 g
.16 oz
Rating
Surge breakdown
between contacts and coil
voltage*
2
Temperature rise (at 65°C
149°F)
Operate time [Set time] (at 20°C
68°F)
Release time [Reset time] (at 20°C
68°F)
Mechanical
characteristics
Expected life
Functional
Destructive
F un ct i o na l
Vibration resistance
Destructive
Mechanical
Electrical
Shock resistance
Conditions for operation, transport and storage*
3
(Not freezing and condensing at low temperature)
Conditions
Solder heating
Max. operating speed
Unit weight
Notes: *1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2 Wave is standard shock voltage of
±1.2×50µs
according to JEC-212-1981
*3 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT.
The code under public is copied to the project directory through sysgen_capture -p shell explorer sysgen_capture -p ie iesample. After compilation and linking, it becomes the English version by defaul...
Circuit Function and AdvantagesThis circuit provides a simple and effective interface between the ADL5371 I/Q modulator and the AD9779A high speed DAC. The ADL5371 and AD9779A are well matched because...
Dear experts, I am a humble man. After I rewired a two-layer board to a four-layer board, CCdebug could not recognize the chip, resulting in the inability to write programs. I have made three sets of ...
The comparator of msp430, in fact, here you just need to understand a picture, two registers, and understand the working principle.
This is the logic diagram of comparator A. Comparator A consists of ...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
