150, 200 WATTS
300, 400 WATTS (PFC AVAILABLE)
WIDE RANGE ADJUSTABLE
MULTIPLE OUTPUTS
ZPS-150
ZPS-200
ZPS-300
ZPS-400
Featuring:
•
Models rated at 150 W, 200 W,
300 W and 400 W continuous power
(180 W, 240 W, 360 W and 480 W
peak power respectively)
•
An auto-ranging input (ZPS-150 A,
200 A) or jumper selectable input
(ZPS-300 A, 400 A) or power factor
corrected, wide range input (ZPS-
300 AP, 400 AP) for 115 V or 230 V,
47-65Hz, single phase AC
•
Typical power factor of 0.99 (ZPS-
300 AP, 400 AP)
•
Four independently isolated and
regulated outputs
•
Wide range of adjustability on
auxiliary outputs (up to 3.3:1)
•
Up to 50% greater peak currents
on auxiliary outputs
•
Low ripple and noise on all outputs
•
Typical 70%-75% efficiency
•
Meets international safety
requirements
•
Meets international Class B EMI
requirements (except for ZPS-
300 AP which meets Class A)
•
DC Power good signal
•
Remote start (Enable) and remote
sense features
•
Optional cover available
•
Medically approved version
available
STANDARD ZPS SERIES
MODEL
ZPS-150A
PWR PFC
150
NO
OUTPUT #1
OUTPUT #2
4.75V To 5.25V 11.5V To 25.2V
@
@
2A To 20A
0.3A To 3A/4.5A pk
4.75V To 5.25V
@
3A To 30A
11.5V To 25.2V
@
0.4A To 4A/6A pk
OUTPUT #3
9.5V To 15.8V
@
0.3A To 4A/5A pk
9.5V To 15.8V
@
0.4A To 5A/6A pk
4.75V To 15.8V
@
0.8A To 8A/12A pk
4.75V To 15.8V
@
1A To 10 A/15A pk
OUTPUT #4
4.75V To 12.6V
@
0.2A To 2A
4.75V To 12.6V
@
0.2A To 2A
4.75V To 15.8V
@
0.4A To 4A/6A pk
4.75V To 15.8V
@
0.6A To 6A/9A pk
ZPS-200A
ZPS-300A
200
NO
NO
300
ZPS-300AP
ZPS-400A
400
ZPS-400AP
4.75V To 5.25V 11.5V To 25.2V
@
@
YES
4.5A To 45A
0.6A To 6A/9A pk
NO 4.75V To 5.25V 11.5V To 25.2V
@
@
YES
5.5A To 55A 0.7A To 7A/10.5A pk
Flexibility is the key word for these
models. Since all four outputs are
independently isolated and regulated,
they can be connected as required
to meet the needs of the system.
Outputs can be connected in either
polarity or stacked to obtain greater
voltages.
An outstanding feature of these
models is the wide range adjustability
of the auxiliary outputs (up to 3.3:1).
The user can adjust the auxiliary out-
puts to meet almost any combination
of voltage requirements from 4.75 V
to 25.2 V. Most of the models provide
a wide input range
for operation anywhere in the world.
Two of the models feature power
factor corrected inputs to meet the
international standards for input
current harmonics. All models are
fully approved to international safety
and EMI standards (including the CE
low voltage directive), simplifying
approvals at the system level.
All models feature highly reliable
designs to ensure years of trouble
free operation.
Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com
150, 200 WATTS
11”x 5”x 2.5”
ZPS-150A, 200A, 250A, 300A
ZPS-150A, 200A
4.0 lbs - 1.8 kgs
5.0 lbs - 2.3 kgs
300, 400 WATTS (PFC AVAILABLE)
13”x 6”x 2.5”
ZPS-400A
ZPS-400A, 400AP
7.0 lbs - 3.2 kgs
ZPS-250A, 250AP, 300A, 300AP
Dimensions:
Inches
Millimeters
SPECIFICATIONS: ALL MODELS
INPUT
AC Input:
Auto-ranging (ZPS-150A & 200A) or Jumper selectable (ZPS-300 A & 400 A) or
power factor corrected wide range (ZPS-300AP & 400AP)- input for 115 V or 230 Vac,
47-65Hz internally fused with appropriate fuses (6A-10A)
Power Factor:
Typical 0.99 for ZPS-300AP & 400AP. Meets EN 61000-3-2.
Inrush:
Cold start AC current is less than 70 A peak for one half cycle of applied power at
230 Vac, limited by a thermistor.
Brownout Protection:
Holds regulation to 85 Vac.
Hold-up Time:
20 ms @ after removal of power at nominal line and full load.
Efficiency:
70%-75% typical
OUTPUT
Adjustability:
Output #1 is adjustable ±5%. Wide range on auxiliary outputs up to 3.3:1
(see table).
Line Load Cross Regulation:
± 0.6% on all outputs, over AC input range and loads within
the ranges specified in the table.
Ripple & Noise:
Less than 1% p-p on all outputs.
Remote Sense
Compensates for 250 mV total line drop. Open sense lead protection.
Temperature Coefficient:
0.03% per degree C.
Stability:
0.1% over 8 hours after 30 minutes warm up.
Transient Response:
Output voltage returns to within 1% in less than 500 µSec for a 25%
load change. Peak transient does not exceed 3%.
Overload Protection:
All outputs protected against short circuit. Input cycling off/on is
required to reset latched-off protection mode.
Overvoltage Protection (Output #1):
Protects against power supply induced overvoltage.
Trip point is factory set so that the output does not exceed 6.4 V.
Peak output Current:
Peak current should be limited to a maximum of 15 seconds.
Enable:
TTL level ”0” or contact closure to the ve-sense line inhibits DC outputs.
DC Power Good:
Provides a TTL level “1” when output #1 is above 4.6 V nominal.
ENVIRONMENTAL
Thermal Protection:
Automatic shutdown if power supply temperature exceeds 90° C.
Temperature Range:
0° C to 40° C at full ratings. Output power linearly derated by 1.7%
per deg. C over 50° C to 70° C.
Safety Agencies:
UL 1950, CSA C 22.2 234 level 5, VDE 0805 /EN 60950, CE marking to low
voltage directive.
Conducted EMI:
All models except ZPS-300AP, meet FCC Part 15 Subpart J, Class B, VDE
0871/B, EN 55022/B. ZPS-300AP meets Class A.
Output Isolation:
Isolated from ground at 50 Vdc.
Cooling:
5 CFM ZPS-150, 15 CFM ZPS-200, 25 CFM ZPS-300 & 300AP, 30 CFM ZPS-400,
35 CFM ZPS-400AP. Forced air required to achieve full ratings.
AC INPUT (90-264 VAC Continuous Range Except ZPS-300A,
400A which require input jumpers to be set for 115V or 230V)
FUNCTION
TB1-(1)
TB1-(2)
TB1-(3)
ZPS-150A & ZPS-200A
115V
230V
Neutral
Line 2
Line
Line 1
Safety Ground
ZPS-300A, 300AP
ZPS-400A, 400AP
115V
230V
Line
Line 1
Neutral
Line 2
Safety Ground
CONNECTOR
Barrier strip
#6-32 screws
0.375”
centers
CONNECTOR
Bus bars
#8-32 screws
DC OUTPUT
FUNCTION
Output #1
MODEL
ZPS-150A & ZPS-200A
ZPS-300A/AP & 400A/AP
Output #2
ZPS-150A & ZPS-200A
ZPS-300A/AP & 400A/AP
Output #3
ZPS-150A & ZPS-200A
ZPS-300A/AP & 400A/AP
Output #4
ZPS-150A & ZPS-200A
ZPS-300A /AP & 400A/AP
LOCATION
TB2-1
TB-22
TB4-1
TB4-2
TB3-1
TB3-2
TB2-3
TB2-4
TB3-3
TB3-4
TB2-5
TB2-6
TB3-5
TB3-6
TB2-7
TB2-8
LOCATION
J1-1
J1-2
J3-1
J3-2
J1-4
J1-3
J3-4
J3-3
J2-2
J2-1
TB2-1
TB2-2
NOTES
4.75V-5.25V
Rtn (Isolated)
4.75V-5.25V
Rtn (Isolated)
11.5V-25.2V
Rtn (Isolated)
11.5V-25.2V
Rtn (Isolated)
9.5V-15.8V
Rtn (Isolated)
4.75V-15.8V
Rtn (Isolated)
4.75V-12.6V
Rtn (Isolated))
4.75V-15.8V
Rtn (Isolated)
NOTES
Enable
Output #1 Rtn
Enable
Output #1 Rtn
DC Power Good
Output #1 Rtn
DC Power Good
Output #1 Rtn
Output #1 Sense+
Output #1 Sense-
Output #1 Sense+
Output #1 Sense-
Barrier Strip
#6-32 Screws
.375” centers
STATUS AND CONTROL
FUNCTION
Enable
ZPS-300A/AP & ZPS-400A/AP
DC Power
Good
Remote
Sense
ZPS-150A & ZPS-200A
ZPS-300A/AP & ZPS-400A/AP
ZPS-150A & ZPS200A
ZPS-300A/AP & ZPS-400A/AP
MODEL
ZPS-150A & ZPS-200A
CONNECTOR
Molex Part #
22-23-2041
Mates with
Molex Part #
22-01-3047
OPTIONS:
Option “C”:
Available with an enclosed cover
Option “M”:
Intended for MEDICAL APPLICATIONS Approved to UL 544, IEC 601/VDE 0750
safety and MDS-201-0004 EMI. Leakage Current is less than 500 µA.
Option “AP”:
For 300 watt and 400 watt power supplies, Power Factor corrected.
Consult factory for other available options.
Molex Part #
22-23-2021Mates
with 22-01-3027
Barrier Strip #
6-32 Screws
.375” Centers
Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com
PCB Design
京公网安备 11010802033920号
EEWORLD
