The AMS1084 series of adjustable and fixed voltage regulators are designed to provide 5A output current and to operate
The
down to 1V input-to-output differential. The dropout voltage of the device is guaranteed maximum 1.5V at maximum output
current, decreasing at lower load currents.
On-chip trimming adjusts the reference voltage to 1%. Current limit is also trimmed, minimizing the stress under overload
conditions on both the regulator and power source circuitry.
The AMS1084 devices are pin compatible with older three-terminal regulators and are offered in 3 lead TO-220 package and
3 and 2 lead TO-263 (Plastic DD).
ORDERING INFORMATION:
PACKAGE TYPE
3 LEAD TO-220
AMS1084CT
AMS1084CT-1.5
AMS1084CT-2.5
AMS1084CT-2.85
AMS1084CT-3.0
AMS1084CT-3.3
AMS1084CT-3.5
AMS1084CT-5.0
2&3 LEAD TO-263
AMS1084CM
AMS1084CM-1.5
AMS1084CM-2.5
AMS1084CM-2.85
AMS1084CM-3.0
AMS1084CM-3.3
AMS1084CM-3.5
AMS1084CM-5.0
OPERATING JUNCTION
TEMPERATURE RANGE
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
FRONT VIEW
TAB IS
OUTPUT
3
2
1
3L TO-263 FRONT VIEW
3
2
1
TAB IS
OUTPUT
PIN CONNECTIONS
2L TO-263 FRONT VIEW
FIXED VERSION
1- Ground
2- V
OUT
3- V
IN
ADJUSTABLE VERSION
1- Adjust
2- V
OUT
3- V
IN
TAB IS
OUTPUT
3
2
1
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1084
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Power Dissipation
Internally limited
Input Voltage
15V
Operating Junction Temperature Range
Control Section
0°C to 125°C
Power Transistor
0°C to 150°C
Storage temperature
- 65°C to +150°C
Soldering information
Lead Temperature (10 sec)
Thermal Resistance
TO-220 package
TO-263 package
300°C
ϕ
JA
= 50°C/W
ϕ
JA
= 30°C/W *
* With package soldering to 0.5in
2
copper area over
backside ground plane or internal power plane
ϕ
JA
can vary
from 20°C/W to
>40°C/W
depending on mounting
technique.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Reference Voltage
(Note 2)
Output Voltage
(Note 2)
Device
AMS1084
AMS1084-1.5
AMS1084-2.5
AMS1084-2.85
AMS1084-3.0
AMS1084-3.3
AMS1084-3.5
AMS1084-5.0
Conditions
I
OUT
= 10 mA
10mA
≤
I
OUT
≤
5A, 1.5V≤ (V
IN
- V
OUT
)
≤
12V
0
≤
I
OUT
≤
5A , 3V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4.35V≤ V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4.5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4.75V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A, 5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 6.5V
≤
V
IN
≤
12V
I
LOAD
= 10 mA , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
(V
IN
- V
OUT
) =3V, 10mA
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5.25V, 0
≤
I
OUT
≤
5A
V
IN
= 8V, 0
≤
I
OUT
≤
5A
∆V
OUT
,
∆V
REF
= 1%, I
OUT
= 5 A (Note 4)
Min
1.238
1.225
1.485
1.470
2.475
2.450
2.82
2.79
2.970
2.940
3.267
3.235
3.465
3.430
4.950
4.900
Typ
1.250
1.250
1.500
1.500
2.500
2.500
2.850
2.850
3.000
3.000
3.300
3.300
3.500
3.500
5.000
5.000
0.3
0.6
0.1
0.2
3
6
3
6
3
6
3
6
3
7
3
6
5
10
1.3
Max
1.262
1.270
1.515
1.530
2.525
2.550
2.88
2.91
3.300
3.360
3.333
3.365
3.535
3.570
5.050
5.100
6
10
0.3
0.4
12
20
12
20
12
20
12
20
15
25
15
25
20
35
1.5
Units
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
mV
mV
%
%
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
V
Line Regulation
Load Regulation
(Notes 2, 3)
AMS1084/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
AMS1084
AMS1084-1.5
AMS1084-2.5
AMS1084-2.85
AMS1084-3.0
AMS1084-3.3
AMS1084-3.5
AMS1084-5.0
Dropout Voltage
(V
IN
-
V
OUT
)
AMS1084/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1084
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Current Limit
Minimum Load
Current
Quiescent Current
Ripple Rejection
Device
AMS1084/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
AMS1084
AMS1084/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
AMS1084
AMS1084-1.5
AMS1084-2.5
AMS1084-2.85
AMS1084-3.0
AMS1084-3.3
AMS1084-3.5
AMS1084-5.0
Conditions
(V
IN
- V
OUT
) = 5V
(V
IN
- V
OUT
) = 12V (Note 5)
V
IN
≤
12V
Min
5.00
Typ
6.00
5
5
Max
7.00
10
10
Units
A
mA
mA
dB
dB
dB
dB
dB
dB
dB
dB
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
(V
IN
-V
OUT
) = 3V, C
ADJ
=25µF
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
V
IN
= 4.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
V
IN
= 5.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 6.3V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 6.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 8V
T
A
= 25°C, 30ms pulse
10mA
≤
I
OUT
≤
5A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
10mA
≤
I
OUT
≤
5A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
60
60
60
60
60
60
60
60
75
72
72
72
72
72
72
68
0.008
55
120
0.2
0.5
5
0.04
Thermal Regulation
Adjust Pin Current
Adjust Pin Current
Change
Temperature Stability
Long Term Stability
RMS Output Noise
(% of V
OUT
)
Thermal Resistance
Junction-to-Case
AMS1084
AMS1084
AMS1084
%W
µA
µA
µA
%
T
A
=125°C, 1000Hrs
T
A
= 25°C , 10Hz
≤
f
≤
10kHz
M Package: Control Circuitry/ Power Transistor
T Package: Control Circuitry/ Power Transistor
0.3
0.003
1
%
%
1.5/4.0
1.5/4.0
°C/W
°C/W
Parameters identified with
boldface type
apply over the full operating temperature range.
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
Electrical Characteristics
.
The guaranteed specifications apply only for the test conditions listed.
Note 2:
Line and Load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output differential
and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 3:
See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction
temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package.
Note 4:
Dropout voltage is specified over the full output current range of the device.
Note 5:
Minimum load current is defined as the minimum output current required to maintain regulation. When (V
IN
- V
OUT
) = 12V the device is guaranteed to
regulate if the output current is greater than 10mA.
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1084
APPLICATION HINTS
The AMS1084 series of adjustable and fixed regulators are easy
to use and have all the protection features expected in high
performance voltage regulators: short circuit protection and
thermal shut-down.
Pin compatible with older three terminal adjustable regulators,
these devices offer the advantage of a lower dropout voltage,
more precise reference tolerance and improved reference stability
with temperature.
Stability
The circuit design used in the AMS1084 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of
150
µF
aluminum electrolytic or a 22µF solid
tantalum on the output will ensure stability for all operating
conditions.
When the adjustment terminal is bypassed with a capacitor to
improve the ripple rejection, the requirement for an output
capacitor increases. The value of 22µF tantalum or
150
µF
aluminum covers all cases of bypassing the adjustment terminal.
Without bypassing the adjustment terminal smaller capacitors can
be used with equally good results.
To ensure good transient response with heavy load current
changes capacitor values on the order of 100µF are used in the
output of many regulators. To further improve stability and
transient response of these devices larger values of output
capacitor can be used.
Protection Diodes
Unlike older regulators, the AMS1084 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent over-stressing the die.
Internal resistors are limiting the internal current paths on the
AMS1084 adjustment pin, therefore even with capacitors on the
adjustment pin no protection diode is needed to ensure device
safety under short-circuit conditions.
Diodes between the input and output are not usually needed.
Microsecond surge currents of 50A to 100A can be handled by the
internal diode between the input and output pins of the device. In
normal operations it is difficult to get those values of surge
currents even with the use of large output capacitances. If high
value output capacitors are used, such as 1000µF to 5000µF and
the input pin is instantaneously shorted to ground, damage can
occur. A diode from output to input is recommended, when a
crowbar circuit at the input of the AMS1084 is used. Normal
power supply cycling or even plugging and unplugging in the
system will not generate current large enough to do any damage.
The adjustment pin can be driven on a transient basis
±25V,
with
respect to the output without any device degradation. As with any
IC regulator, none the protection circuitry will be functional and
the internal transistors will break down if the maximum input to
output voltage differential is exceeded.
D1
V
IN
AMS1084
IN
OUT
ADJ
C
ADJ
10µF
V
OUT
R
1
R
2
+
C
OUT
150µF
Overload Recovery
When the power is first turned on, as the input voltage rises, the
output follows the input, permitting the regulator to start up into
heavy loads. During the start-up, as the input voltage is rising, the
input-to-output voltage differential remains small, allowing the
regulator to supply large output currents. A problem can occur
with a heavy output load when the input voltage is high and the
output voltage is low, when the removal of an output short will
not permit the output voltage to recover. The load line for such a
load may intersect two points on the output current curve. In this
case, there are two stable output operating points for the
regulator. With this double intersection, the power supply may
need to be cycled down to zero and brought up again to make the
output recover.
Ripple Rejection
The ripple rejection values are measured with the adjustment pin
bypassed. The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1 (normally 100Ω
to120Ω) for a proper bypassing and ripple rejection approaching
the values shown. The size of the required adjust pin capacitor is
a function of the input ripple frequency. If R1=100Ω at 120Hz the
adjust pin capacitor should be 25µF. At 10kHz only 0.22µF is
needed.
The ripple rejection will be a function of output voltage, in
circuits without an adjust pin bypass capacitor. The output ripple
will increase directly as a ratio of the output voltage to the
reference voltage (V
OUT
/ V
REF
).
Output Voltage
The AMS1084 series develops a 1.25V reference voltage between
the output and the adjust terminal. Placing a resistor between
these two terminals causes a constant current to flow through R1
and down through R2 to set the overall output voltage.
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1084
APPLICATION HINTS
This current is normally the specified minimum load current of
10mA. Because I
ADJ
is very small and constant it represents a
small error and it can usually be ignored.
Connected as shown, R
P is
not multiplied by the divider ratio.
Using 16-gauge wire the parasitic line resistance is about 0.004Ω
per foot, translating to 4mV/ft at 1A load current. It is important
to keep the positive lead between regulator and load as short as
possible and use large wire or PC board traces.
Thermal Considerations
The AMS1084 series have internal power and thermal limiting
circuitry designed to protect the device under overload
conditions. However maximum junction temperature ratings
should not be exceeded under continuous normal load conditions.
Careful consideration must be given to all sources of thermal
resistance from junction to ambient, including junction-to-case,
case-to-heat sink interface and heat sink resistance itself. To
ensure safe operating temperatures and reflect more accurately
the device temperature, new thermal resistance specifications
have been developed. Unlike older regulators with a single
junction-to-case thermal resistance specification, the data section
for these new regulators provides a separate thermal resistance
and maximum junction temperature for both the Control Section
and the Power Transistor. Calculations for both temperatures
under certain conditions of ambient temperature and heat sink
resistance and to ensure that both thermal limits are met.
Junction-to-case thermal resistance is specified from the IC
junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.
V
IN
AMS1084
IN
OUT
ADJ
I
ADJ
50µA
V
OUT
V
REF
R1
R2
V
OUT
= V
REF
(1+
R2/R1)+I
ADJ
R2
Figure 1. Basic Adjustable Regulator
Load Regulation
True remote load sensing it is not possible to provide, because the
AMS1084 is a three terminal device. The resistance of the wire
connecting the regulator to the load will limit the load regulation.
The data sheet specification for load regulation is measured at the
bottom of the package. Negative side sensing is a true Kelvin
connection, with the bottom of the output divider returned to the
negative side of the load.
The best load regulation is obtained when the top of the resistor
divider R1 is connected directly to the case not to the load. If R1
were connected to the load, the effective resistance between the
regulator and the load would be:
R
P
x ( R2+R1 ) ,
R1
R
P
= Parasitic Line Resistance
V
IN
AMS1084
IN
OUT
ADJ
R
P
PARASITIC
LINE RESISTANCE
R1*
R
L
R2*
*
CONNECT R1 TO CASE
CONNECT R2 TO LOAD
Figure 2. Connections for Best Load Regulation
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
[color=#333333] Shared bicycles are becoming more and more popular now. The most common ones on the market are basically in the form of smart locks. Smart locks of the Internet of Things have been wid...
[i=s]This post was last edited by ID.LODA on 2018-12-21 09:19[/i] [font=微软雅黑][size=4] [color=#333333]The use of JSON strings in IoT devices is also quite common nowadays. Let’s share and learn about i...
I am a novice, and I need help on how to port meanshift from opencv to DM642, because I don't know the calculation method of cvMeanshift function body, nor do I know how to calculate the back projecti...
Hello everyone! I am working on the backlight driver under WINCE. First, I provide PM.EXE. My backlight supports the power management capabilities of [b]D0, D1, D4[/b] and I turn the backlight on at D...
1. Installation of MDK
MDK, the ARM development tool developed by Keil, is used to develop embedded applications for a series of microcontrollers based on the ARM core . It is suitable for developers ...
I recently upgraded MDK to V5.25 and found that there are many libraries in the Managing Run-Time Environment. Compared with the past, it is much better, from the bottom-level driver to the upper-le...[Details]
We have come a long way from the 2G era, and now 5G is about to be commercialized. Suddenly, we realize that time has passed quickly, but technology has never stopped. The activation of 5G heralds ...[Details]
Recently, there was news that the US government asked Google to shut down the Android operating system for ZTE phones. After that, some people even imagined what the consequences would be if Intern...[Details]
Artificial Intelligence (AI) is undoubtedly the hottest topic in the technology industry in the past one or two years. In addition to the huge investments made by technology giants, financial and o...[Details]
With the large-scale development of the domestic household photovoltaic market and the improvement of component and inverter technology, the system cost has dropped significantly in the past year. The...[Details]
In recent years, the application of high-brightness LED has developed rapidly, especially in signboards and traffic lights. For automotive applications, LED is also very attractive. Long life, shock ...[Details]
ADC Introduction: ADC (Analog-to-Digital Converter). That is, converting analog signals into digital signals for processing. When storing or transmitting, analog-to-digital converters are almost ...[Details]
STM32 Watchdog Summary I have been adjusting the development board of Atom Brother for more than a year, and it is basically usable, but I still don't understand the working mechanism of some basi...[Details]
The photovoltaic industry has become a new business card for China to the world. It not only represents China's leading technology, but also constantly breaks various records with its development spee...[Details]
The clock system of STM32 can be directly summarized in a diagram (from the STM32F10X reference manual). The following is an analysis of this diagram 1. STM32 input clock source 1.1 Function of cl...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
