EEWORLDEEWORLDEEWORLD

Part Number

Search

WLS1A00BQ4BT3

Description
Limitless™ Single Switch Adapter
File Size2MB,47 Pages
ManufacturerHoneywell
Websitehttp://www.ssec.honeywell.com/
Download Datasheet View All

WLS1A00BQ4BT3 Overview

Limitless™ Single Switch Adapter

Installation and Technical Manual for the
Limitless™ Series WDRR Receiver
50063987
ISSUE 5
WARNING
DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
PERSONAL INJURY
The WDRR must be installed in accordance with the
requirements specified in this document in order to comply
with the specific Country Communication Agency
requirements. (i.e. FCC, IC, ETSI, ACMA, etc.) See
Section 3 as it requires choosing the correct Country Use
Code and thus allowable antenna and/or cable usage.
WARNING
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the
control strategy results in a safe operating condition if any
crucial segment of the control solution fails.
Honeywell customers assume full responsibility for learning
and meeting the required Declaration of Conformity,
Regulations, Guidelines, etc. for each country in their
distribution market.
Failure to comply with these instructions could result in
death or serious injury.
Pay attention to ESD discharge at dc-in port.
WARNING
WARNING
Korean Communication Commission does not allow this
equipment to be used for rescue service.
Anatel states that this device works as a secondary
function model. It may not be used as a protection device
against harmful interference. It cannot cause interference
with systems that are running as primary function.
WARNING
CAUTION
* Power to the WDRR should not be applied during
installation of antenna as damage could occur to the
WDRR electronics.
WARNING
To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 20 cm or
more should be maintained between the antenna of this
device and persons during device operation To ensure
compliance, operation at closer than this distance is not
recommended. The antenna used for this transmission
must not be co-located in conjunction with any other
antenna or transmitter.
Failure to comply with these instructions could result in
death or serious injury.
RF EXPOSURE
CAUTION
* The WDRR receiver offers optimal performance when
paired with Limitless™ inputs that have a firmware
version of 7170 or a greater number (i.e., FW7170 will be
printed on the Limitless™ input label). If the Limitless™
input is paired with older firmware (FW7170 or a lesser
number), the WDRR may exhibit delayed responses
under simultaneous operation.
Sensing and Productivity Solutions
Infrared Data Collection
:victory: :victory: :victory: :victory:...
eeworld.com MCU
Take advantage of the boom in artificial intelligence and start learning now!
[size=3]:pleased:Learning is life-long, as an engineer, hurry up to learn about what’s hot these days~~ Hot topics of this issue: Knowledge about artificial intelligence (AI)[b][color=#ff0000]The foll...
okhxyyo Robotics Development
IoT Smart Home-Overall Functional Integration of Kitchen
Basically, the overall function of the kitchen is realized!The following is a flowchart: (The program after minor adjustments shall prevail)The program is introduced in detail in the experience posts ...
anananjjj DIY/Open Source Hardware
I would like to ask about the selection of DAC reference voltage
Many DACs have built-in reference voltage sources, but some test data show that the noise may be lower when using an external reference voltage source. Although the model of the external reference sou...
jelly_bessie Analog electronics
ST FOC electrical angle problem
Regarding the electrical angle of the ST FOC magnetic encoder, I have two questions I would like to ask the experts 1. Using the magnetic encoder AS5048 to read the mechanical angle of 0-360 degrees, ...
sdkdwyb Motor Drive Control(Motor Control)
Ask about the chip currency
[i=s]This post was last edited by paulhyde on 2014-9-15 09:02[/i]I am a newbie and don’t know how to get ChipCoins. Please help me....
sjm070 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1741  349  2503  2706  355  36  8  51  55  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号