WLS1A07AQ4BT1 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > WLS1A07AQ4BT1

Preview

WLS1A07AQ4BT1: DescriptionLimitlessâ¢ Single Switch Adapter; File Size2MB，47 Pages; ManufacturerHoneywell; Websitehttp://www.ssec.honeywell.com/

Download Datasheet View All

WLS1A07AQ4BT1 Overview

Limitlessâ¢ Single Switch Adapter

Preview

Download Datasheet

View All

Installation and Technical Manual for the

Limitless™ Series WDRR Receiver

50063987

ISSUE 5

WARNING

•

DO NOT USE these products as safety or emergency

stop devices or in any other application where failure of

the product could result in personal injury.

Failure to comply with these instructions could result in

death or serious injury.

PERSONAL INJURY

•

The WDRR must be installed in accordance with the

requirements specified in this document in order to comply

with the specific Country Communication Agency

requirements. (i.e. FCC, IC, ETSI, ACMA, etc.) See

Section 3 as it requires choosing the correct Country Use

Code and thus allowable antenna and/or cable usage.

WARNING

Honeywell does not recommend using devices for critical

control applications where there is, or may be, a single point

of failure or where single points of failure may result in an

unsafe condition. It is up to the end-user to weigh the risks

and benefits to determine if the products are appropriate for

the application based on security, safety and performance.

Additionally, it is up to the end-user to ensure that the

control strategy results in a safe operating condition if any

crucial segment of the control solution fails.

Honeywell customers assume full responsibility for learning

and meeting the required Declaration of Conformity,

Regulations, Guidelines, etc. for each country in their

distribution market.

Failure to comply with these instructions could result in

death or serious injury.

•

Pay attention to ESD discharge at dc-in port.

WARNING

•

Korean Communication Commission does not allow this

equipment to be used for rescue service.

•

Anatel states that this device works as a secondary

function model. It may not be used as a protection device

against harmful interference. It cannot cause interference

with systems that are running as primary function.

WARNING

CAUTION

* Power to the WDRR should not be applied during

installation of antenna as damage could occur to the

WDRR electronics.

WARNING

•

To satisfy FCC RF exposure requirements for mobile

transmitting devices, a separation distance of 20 cm or

more should be maintained between the antenna of this

device and persons during device operation To ensure

compliance, operation at closer than this distance is not

recommended. The antenna used for this transmission

must not be co-located in conjunction with any other

antenna or transmitter.

Failure to comply with these instructions could result in

death or serious injury.

RF EXPOSURE

CAUTION

* The WDRR receiver offers optimal performance when

paired with Limitless™ inputs that have a firmware

version of 7170 or a greater number (i.e., FW7170 will be

printed on the Limitless™ input label). If the Limitless™

input is paired with older firmware (FW7170 or a lesser

number), the WDRR may exhibit delayed responses

under simultaneous operation.

Sensing and Productivity Solutions

Limitless™

WDRR Receiver

IST OF

IGURES

Issue 5

50063987

Figure 1. European Declaration of Conformity (DoC)

.................................................................................................. 9

Figure 2. Limitless™ WDRR DIN Rail Receiver with location call-out

....................................................................... 12

Figure 3. Limitless™ WDRR DIN Rail Receiver with WDRRPWRASM connected

................................................... 13

Figure 4. Limitless™ Switch Housing

........................................................................................................................ 20

Figure 5. Limitless™ WDRR Housing

........................................................................................................................ 20

Figure 6. Limitless™ Switch with Function Button Depressed

.................................................................................. 20

Figure 7. Limitless™ Switch Label Placement

........................................................................................................... 20

Figure 8. Limitless™ WDRR Operation and LED Functions Chart

............................................................................ 22

Figure 9. Radiation Pattern of an Omni-directional Antenna

..................................................................................... 25

Figure 10. Limitless™ switch to WDRR Antennas with RF Signal Line of Sight (LOS) Free From Obstacles

......... 26

Figure 11. Limitless™ switch to WDRR Antennas with RF Signal Line of Sight (LOS) Affected by

......................... 26

Figure 12. Limitless™ WDRR RP-SMA Connection, Integral

.................................................................................... 28

Figure 13. Limitless™ WDRR RP-SMA Connection, Remote

................................................................................... 28

Figure 14. Straight, Right-Angle, and Tilt-and-Swivel antennas

................................................................................ 28

Figure 15. Adhesive Mount Antenna – Step 1. Pre-clean the surface

...................................................................... 29

Figure 16. Adhesive Mount Antenna – Step 2. Peel Protection from Adhesive Strip................................................

Figure 17. Adhesive Mount Antenna – Step 3. Mount the Antenna...........................................................................

Figure 18. Mast Mount Antenna – Tighten nut on mounting bracket

...................................................................... 30

Figure 19. Mast Mount Antenna – Side View with Attachment to Pipe

.................................................................. 30

Figure 20. Magnetic Mount Base with Antenna – Mounted on Steel Surface

.......................................................... 31

Figure 21. WAN09RSP Magnetic Mount Antenna

..................................................................................................... 31

Figure 22. WAN10RSP Magnetic Mount Antenna

..................................................................................................... 31

Figure 23. Through-hole mount antenna

.................................................................................................................... 31

Figure 24. Highest RF signal when antennas are as parallel to each other as possible (parallel arrangement

shown with the Limitless™ WPMM monitor and WGLA switch)

................................................................................ 32

Figure 25. Limitless™ WDRR Mounting Clips

........................................................................................................... 35

Figure 26. Limitless™ WDRR Mounting Tabs

............................................................................................................ 35

IST OF

ABLES

Table 1 –Table of Abbreviations and Definitions

.......................................................................................................... 2

Table 2 –Table Symbol Definitions

............................................................................................................................... 3

Table 3 – North America; Country Use Code “A”

........................................................................................................ 4

Table 4 – Asia Pacific; Country Use Code “B”

............................................................................................................ 4

Table 5 – European Union; Country Use Code “B”

..................................................................................................... 4

Table 6 – Other European Countries; Country Use Code “B”

..................................................................................... 4

Table 7 – Approvals and Ratings

................................................................................................................................. 5

Table 8 – Radio Module Specifications

....................................................................................................................... 5

Table 9 – Electrical Specifications

............................................................................................................................... 5

Table 10 – Environmental Specifications

..................................................................................................................... 6

Table 11 – Country Use Code A Antenna Options

..................................................................................................... 10

Table 12 – Country Use Code B Antenna Options.....................................................................................................

sensing.honeywell.com

Recommended Resources

Capacitor cleverly used as transformer circuit

30Wx2 power connector

HT7704 touch step dimming light circuit

555 daytime locked photosensitive voice-activated switch circuit

Bistable circuit with multiple inputs

Anti-condensation automatic exhaust and bird chirping sound circuit for greenhouse or greenhouse

Beijing is urgently hiring FPGA development engineers, DSP development engineers, and hardware design engineers (fresh graduates are also welcome!): [align=center][align=left][b][color=#0000ff]Recruitment position: FPGA development engineer (2 people) [/color][/b][/align][/align][align=left][font=微软雅黑][size=3]Job responsibilities: [/size][/font][/...; eric_wang Recruitment

Eight USB Questions and Answers (For Beginners): Question 1: What is the structure of the USB transmission line? Answer 1: A USB transmission line consists of four lines: ground line, power line, D+, and D-. D+ and D- are differential input lines, w...; songbo MCU

【Running posture training shoes】No.004-Sensor production and primary data processing: The previous article introduced data acquisition and real-time waveform display . This article introduces the sensor production process and primary data processing designed by me . This work uses four...; sipower onsemi and Avnet IoT Innovation Design Competition

EDMA chip select CE: EDMA chip select CE is high when there is no data in the space pointed by CE. Will it be low for a short time, which is the setup time period? Please help! !...; cjqlmy DSP and ARM Processors

What is the principle of the pull-up resistor of the P0 port of the 51 single-chip microcomputer?: The byte address of port P0 is 80H, and the bit address is 80H to 87H. Each bit line of port P0 has the same but independent logic circuit. The circuit diagram of the bit structure of a certain bit of...; gchen51 51mcu

MSP-EXP430FR5739 Experimental Board Application Experience Sharing with Prizes!: The deyisupport community promotes the MSP-EXP430FR5739 experiment board. For its features, for example, it supports the new generation of MSP430 microprocessor devices with integrated ferroelectric r...; EEWORLD社区 Microcontroller MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components