EEWORLDEEWORLDEEWORLD

Part Number

Search

B37G94G062G99

Description
RF BNC Connector, Female, Panel Mount, Cable Mount, Crimp Terminal, Jack,
CategoryThe connector    The connector   
File Size1MB,43 Pages
ManufacturerMACOM
Websitehttp://www.macom.com
Download Datasheet Parametric View All

B37G94G062G99 Overview

RF BNC Connector, Female, Panel Mount, Cable Mount, Crimp Terminal, Jack,

B37G94G062G99 Parametric

Parameter NameAttribute value
MakerMACOM
Reach Compliance Codeunknown
Other featuresINSERTION LOSS MAX AT 3GHZ, VSWR AT 1GHZ: 1.05
Body/casing typeJACK
Characteristic impedance75 Ω
Connector typeRF BNC CONNECTOR
Contact to complete cooperationGOLD (63) OVER COPPER
Contact completed and terminatedGOLD (63) OVER COPPER
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER/BRASS
Coupling typeBAYONET
DIN complianceNO
Filter functionNO
IEC complianceNO
Insertion loss0.2 dB
insulator materialPTFE
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberBNC
Installation methodSTRAIGHT
Installation typeCABLE
Maximum operating frequency4 GHz
Panel mountingYES
Termination typeCRIMP
voltage standing wave ratio1.3
What a terrible early morning.
Around 2 a.m. today, I walked outside the building and was shocked by the scene in front of me. Oh my god, thick smoke and dust covered the earth. I have been here for some time. I have never seen suc...
ienglgge Talking
Help bdata
I defined a BDATA like this, uint bdata port; port^0=P3^5; port^1=P3^6; port^2=P3^7; port^3=P2^6; port^4=P2^7; port^5=P1^6; I want to use it to operate the port of the microcontroller, but it doesn't ...
renyunpei 51mcu
How to compare the hierarchical schematics (multiple schematics correspond to one PCB) in AD software to show the differences between the schematics and PCB?
As the title says, after using AD software to design a board with multiple schematics corresponding to one PCB, how can I compare the differences between the schematics and the PCB? I only know how to...
yjguohua PCB Design
There is a strange phenomenon at the MCU IO port, please help!
Hello everyone! The microcontroller I use is C8051F020. There are problems with my three IO ports. The IO ports are set to open drain state, and the cross switch is also fine. There are no digital per...
shi991 Embedded System
Change the 51 microcontroller infrared remote control program into a program that can run in the Arduino compilation environment
I am a beginner and I am confused about the program of single-chip microcomputer. I want to use infrared remote control to control a robot. The board is Arduino 2009 MEGA168, crystal oscillator 16M, b...
34747124 Robotics Development
Repost: Cui Yongyuan wrote to the president of the Agricultural University and proposed a debate on GMOs in front of students
Since I am basically ignorant about GMOs, the reposting does not necessarily represent my own views. However, I still think that the current science and technology may not be able to make a definitive...
wangfuchong Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1758  957  1702  1534  2478  36  20  35  31  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号