ATmega128+CC1101 Design Experience
First of all, CC1100 is an upgraded version of CC1101. Except for a few more registers in the configuration registers, CC1101 is completely compatible with CC1100, w...
Statement: This post is to make up for the mistake on the 23rd. I hope everyone will forgive me.Let's get to the point (this question is a bit broad, I don't know if it's appropriate to talk about it)...
[color=#000][font=宋体, "][size=12px]Stdint.h defines standard extended integer types, including exact-length types, minimum-length types, fast-length types, and maximum-length types. What are the benef...
a. Full-waveform rectifier circuit patterning composed of OP amplifier
The full-wave rectifier circuit in Figure 1 often has an unbalanced waveform due to the unintegrated gain of the positive end (pl...
[font=楷体, 楷体_GB2312][size=5][b][url=https://www.eeworld.com.cn/training/2013/TI_WEBENCH_0624/288.html]Overview of WEBENCH System Power Architecture[/url][/b] [b][url=https://www.eeworld.com.cn/trainin...
Can any expert tell me how to record and play voice through A/D and D/A conversion? It's urgent. Thank you very much. If you are interested, you can chat with me on Q, 270329846...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
