Operating Temperature Range ..........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Reflow Temperature (Note 1) ................................+235°C
Note 1:
The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, T
A
= -40°C to +85°C. Typical specifications are at T
A
= +25°C,
unless otherwise noted.) (Note 2)
PARAMETER
Input Voltage Range
Input Undervoltage Lockout
Supply Current (Ground Current)
Shutdown Supply Current
REGULATOR CIRCUIT
Output Current
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range
SET Reference Voltage
SET Dual Mode
TM
Threshold
SET Input Leakage Current
1mA
≤
I
OUT
≤
150mA, T
A
= +25°C
1mA
≤
I
OUT
≤
150mA, T
A
= -40°C to +85°C
1mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
100mA, T
A
= +25°C
2mA
≤
I
OUT
≤
100mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
(Note 3)
V
SET
I
SET
V
SET
= 0, +1.2V (Note 3)
SYMBOL
V
IN
V
UVLO
I
Q
I
SHDN
V
IN
falling
I
OUT
= 0
I
OUT
= 300mA
T
A
= +25°C
300
-1.3
-2.3
-2.7
-1.1
-2.0
-2.5
V
SET
1.200
CONDITIONS
MIN
2.5
2.25
82
96
0.1
TYP
MAX
5.5
2.47
136
1
UNITS
V
V
µA
µA
mA
+1.3
+2.3
+2.7
+1.1
+2.0
+2.5
5.0
1.258
±100
V
V
mV
nA
%
%
1.229
185
±20
Dual Mode is a trademark of Maxim Integrated Products, Inc.
1. What is an adder? An adder is used to perform addition. It is a device that generates the sum of numbers. A device that takes the addend and the augend as input and the sum and the carry as outpu...
I want to design a circuit based on cc2530 that can realize HC-SR04 ultrasonic ranging and 1602 display of ranging results. Can it be realized by directly connecting these three? Can someone who knows...
One day, the led screen software can no longer be used. It says that CommonCtrli.dll is missing, and I can't find such a dll file on the Internet. This is the software iconCan anyone help me solve a s...
Urgent, has the TI sample application webpage crashed recently? Every time I settle, an error occurs. It has been quite a long time. I wonder if anyone has encountered this problem?...
[i=s]This post was last edited by Diguapatch on 2014-8-19 18:46[/i] In webench online design software, there are amplification and ADC design solutions specifically for sensors. In webench, the types ...
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
