1. Use the timer to make the light flashWhen we were learning microcontrollers, the first example we used was to make the light flash. We did that with a timer program. Now, looking back, this is not ...
My computer is Win8.1. I connected the downloader to the minimum system board of STM32F10ZET6 and plugged it into the USB port. I couldn't connect it from the task manager. I opened the properties and...
Wireless networking technologies such as WiFi, ZigBee, and Bluetooth are suitable for consumer applications of the Internet of Things (IoT), but many industrial and other IoT applications need to oper...
Help analyze the IC model on the conversion board
This is a finished board that converts RGB+SYNC to component output. But the IC model on it has been worn off by the manufacturer. I can't see it. I h...
The display has been upgraded from 1206 to 12864 (controller T7920). I will be on holiday in the afternoon, so I will treat it as a pre-holiday gift. Attached is the 12864 driver...
[color=#000000]Due to Baidu network disk, the download address of the video and routines for [/color][color=#ff0000]51 MCU Easy to Use - Based on STC15W4K Series[/color][color=#000000] has changed. Th...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
OC faults may be the most frequent and the most frequent of all faults in the inverter. They alarm during the startup process, during the shutdown process, during operation, and even when powered o...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Preface
In recent years, white light LEDs have gradually replaced incandescent bulbs and fluorescent lamps because they have unparalleled advantages over traditional light sources in terms...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
0 Introduction
With the rapid development of social economy and science and technology, electric locomotives, subways and electric vehicles will be widely used. The power conversion and cont...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
