BUS-63106-410Q datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > logic> logic> BUS-63106-410Q

BUS-63106-410Q: DescriptionBus Driver/Transceiver; Categorylogic logic; File Size124KB，16 Pages; ManufacturerData Device Corporation

Download Datasheet Parametric View All

BUS-63106-410Q Overview

Bus Driver/Transceiver

BUS-63106-410Q Parametric

Parameter Name	Attribute value
Maker	Data Device Corporation
Reach Compliance Code	compliant

Preview

Download Datasheet

View All

BUS-63100 SERIES

MIL-STD-1553 DATA BUS

SINGLE AND DUAL TRANSCEIVERS

BUS-63102

BUS-63105

BUS-63125

DESCRIPTION

The BUS-63100 transceivers are

complete transmitter and receiver

pairs conforming fully to MIL-STD-

1553A and 1553B. Features available

with selected models of this high reli-

ability series include: Smiths and

Harris interface type choices,

+12 V/+15 V power supply voltage

range, variable threshold levels, and

single (24-pin DDIP or square) and

completely independent dual redun-

dant (36-pin DDIP) packaging config-

urations. All models are also available

in flat packs.

The receiver section of the BUS-

63100 series accepts phase-modula-

ted bipolar data from a MIL-STD-1553

Data Bus and produces TTL signal

data at its outputs: RX Data Out and

RX Data Out. These outputs repre-

sent positive and negative variations

of the input data signals beyond an

internally fixed or externally set

threshold level. An external STROBE

input enables or disables the receiver

outputs.

The transmitter section accepts bipo-

lar TTL signal data at its TX Data and

TX Data input lines and produces

phase modulated bipolar data at the

TX Data and TX Data outputs. The

transmitters’ output voltage level is

typically 28 Vpp to 30 Vpp. An exter-

nal input, INHIBIT, takes priority over

the transmitter inputs and disables

the transmitter when activated with a

logic “1.”

The small size and different model

capabilities available with the

BUS-63100 series simplify engineer-

ing design, making it an excellent

choice for interfacing with any

MIL-STD-1553 system.

FEATURES

•

Conforms Fully to MIL-STD-1553A

and 1553B

•

Some Models Available to Military

(DESC) Drawings

•

Model Capabilities:

Single or Dual Redundant

Packaging

-12 V/-15 V Power Supply Voltage

Range Available

Harris or Smith’s I/O Compatibility

•

Small Size:

Single – 24-Pin DDIP or Square

Dual – 36-Pin DDIP Flat Packs

•

Low Power

•

High Reliability – LSI

±V

1553

DATA

BUS

+5 V

RECEIVER STROBE

BI PHASE

TTL DATA

PHASE MODULATED

BIPOLAR DATA

RX Data In

SHORT OR

LONG STUB

COUPLING

ISOLATION

TRANSFORMER

RX Data In

RECEIVER SECTION

COMPARATOR

RX Data

LIMITER

FILTER

RX Data

DECODER

COMPARATOR

TRANSMITTER SECTION

DRIVER

TX Data Out

SHAPING

NETWORK

DRIVER

TX Data Out

SHAPING

NETWORK

TX Data In

ENCODER

TX INHIBIT

FIGURE 1. BUS-63100 BLOCK DIAGRAM

DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.

Recommended Resources

Complementary differential fully symmetrical power amplifier 01

Sanyo brand SR124 refrigerator circuit

24V power supply using integrated block 05

Using LM3916 to measure the output voltage circuit from 0 to 10V

Smart transmitter circuit with HART interface

5V/10A100kh choke coil AC converter using SIPMOS transistor

How do you set the fuse bits of AVR?: I have locked up two microcontrollers...:Sad:...; jasminebilin Microchip MCU

#Meet friends by demolishing# Just unpacked portable formaldehyde tester: [i=s]This post was last edited by mylsf on 2015-7-23 20:19[/i] I bought a portable formaldehyde tester a few days ago.I disassembledIt was disassembled into two parts. The upper part is the back cover...; mylsf Making friends through disassembly

A very good forum: I bought the 4412 development board from Youmi before, and I really regret it. I posted on their forum. Everyone replied, this forum is still good, the discussion atmosphere is very good, I regret buy...; matao1314 Embedded System

51 MCU variable definition: How to define variables in 51 MCU? Where are global variables and local variables stored? And if I want to define a variable in user RAM with address 0x32, how to define the variable in the bit addres...; davidlong98 51mcu

Please advise on the use of GDO0 in CC2500: void RFSendPacket(char *txBuffer, char size) { TI_CC_SPIWriteBurstReg(TI_CCxxx0_TXFIFO, txBuffer, size); // Write TX data TI_CC_SPIStrobe(TI_CCxxx0_STX); // Change state to TX, initiating // data tran...; nishishab Embedded System

Can you guys help me check if my circuit analysis is correct?: As shown in the figure, I want to get a fixed VOUT from VIN, and limit the current at VOUT to a value. For example, if I input VIN15V and want to get VOUT5V, ic=1A, then ib=5mA. My analysis is this. T...; startt Analog electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components