3
Void Polyester Label Products
FMV02 • FMV12 • FMV22 • FMV32 • FMV0E
Technical Data
February, 2007
Product Description
3M™ Void Polyester Label Products are tamper-indicating stocks designed to provide
a “void” message in the facestock when removal is attempted. These void polyester
labels utilize 3M™ Adhesive P1410 which is an aggressive tackified emulsion acrylic
adhesive that offers excellent adhesion to a wide variety of substrates, including
polyolefins.
Construction
Product
3M™ Void
Polyester Label
Product FMV02
3M™ Void
Polyester Label
Product FMV12
3M™ Void
Polyester Label
Product FMV22
3M™ Void
Polyester Label
Product FMV32
3M™ Void
Polyester Label
Product FMV0E
Facestock
.002 in. Silver Void
Polyester TC
.002 in. White Void
Polyester EDP
.002 in. White Void
Polyester TC
.002 in. Silver Void
Polyester Translucent
EDP
.002 in. Silver Void
Polyester TC
Adhesive
P1410
Perm. 18
P1410
Perm. 18
P1410
Perm. 18
P1410
Perm. 18
P1410
Perm. 18
Liner
50# SC
3.1 mil semi-bleached
super calendered kraft sheet
50# SC Remoist
3.1 mil semi-bleached
super calendered kraft sheet
50# SC
3.1 mil semi-bleached
super calendered kraft sheet
50# SC Remoist
3.1 mil semi-bleached
super calendered kraft sheet
50# SC C2S
3.1 mil semi-bleached
super calendered kraft sheet
(Calipers are nominal values)
Typical Physical
Properties
Note: The following technical information and data should be considered representative
or typical only and should not be used for specification purposes.
Adhesion properties determined per TLMI Method using 1.0 mil polyester with 0.9 mils
of adhesive on a stainless steel panel.
Peel Adhesion
Loop Tack
Shear
Adhesive Coat Weight
Liner Release
Application Temperature
Service Temperature
Conformability
3.0 lbs./in. (528 N/m)
1.8 lbs./in. (316 N/m)
1.0 hour
1.75 g/100 in.
2
± 10%
15 to 50 g/2 in.
TLMI Method, 180° Peel, 12"/min., 1" wide sample
TLMI Method, 12"/min., 1" wide sample
TLMI Method, 0.25 in.
2
x 500g
3M Method E10MFP01
TLMI Method, 180° removal, 300 in./min.
40°F to 120°F (5°C to 49°C)
-20°F to 240°F (-29°C to 115°C)
Semi-rigid – Label is suitable for flat or slightly curved surfaces.
3M
™
Void Polyester Label Products
FMV02 • FMV12 • FMV22 • FMV32 • FMV0E
Features
• The polyester film is top coated to accept most film ink systems and thermal transfer printing.
• Meets CONEG requirements.
• Adhesive dry ingredients are listed by FDA as indirect food contact additives when used in
food packaging with minimum opportunity for exposure. See 21 CFR 175.105.
• Liner is designed for high-speed die-cutting and matrix stripping. Not recommended for sheet
on press applications. The C2S version has a light coating of silicone on the backside to
reduce label pick and is effective when used in conjunction with soft adhesives and heavy
adhesive coating weights. The remoist version has been remoisturized after silicone coating to
restabilize the sheet and reduce side curl.
• Gloss topcoat is designed to be printable with a variety of film inks and thermal transfer
ribbons. The following inks and thermal transfer ribbons have been evaluated and found to
give excellent adhesion when tested with 3M™ Tape 610 and 3M™ Tape 810. However,
press conditions vary and proper evaluation using your specific conditions is critical and
highly recommended for successful ink and ribbon adhesion.
Supplier UV Inks
XSYS Print Solutions
Ink Series
UNV80071
USC50022
USC10031
Ultra Kote 1800 OPV
PSST-3952
02-022, 80049, 02304, 021019
HMF80071
HMF90100
MHF30004
WFLO 42976
Aqua Polyscreen Plus
Aqua Poly Cup
SCF 6551
FCTB65L2
FCTD65L4
FCTE65L3
FCTH65L5
GV124
Ribbon Series
AXR7 +
W137-C
M-250
R510-W
SP330, DC400
Prime Mark, PM350
B110A
BC110C
3022, 4085 Plus
4070
4075
-2-
Printing Process
Letterpress
Screen
Screen
Flexo
Screen
Screen
Flexo
Flexo
Flexo
Flexo
Flexo
Flexo
Flexo
Flexo
Flexo
Flexo
Gravure
Screen
Ribbon Type
Resin
Wax
Wax/Resin
Resin
Resin
Wax/Resin
Wax/Resin
Resin
Wax
Resin (UV+)
Resin
Printing
Environmental Inks
Nazdar
Norcote
Water Based
XSYS Print Solutions
Water Ink Technologies
Environmental Inks
Wykoff Inks
Solvent Based
Siegwerk Ink
Nazdar
Thermal Transfer
Ribbon Supplier
Armor
DNP
iimak
Ricoh
Sony
3M
™
Void Polyester Label Products
FMV02 • FMV12 • FMV22 • FMV32 • FMV0E
Application Ideas
• Tamper-indicating labels and seals for packaging applications.
• Non-transferable durable goods label.
Die-Cutting
The compact “void” message permits manufacture of labels as small as
1
/
2
in. x 1
1
/
4
in.
(13 mm x 32 mm).
It is recommended that the user test for the presence of the “void” message on every
roll of label seals as they process them, to insure the product quality and consistency.
Which can be done by laminating a label seal to an untreated polyester film test surface.
The label seal should be wiped down with a squeegee, allowed to dwell 10 minutes, and
then removed to observe the presence and functions of the “void” message on both the
facestock and the substrate. It is also recommended that the user test each lot of label
seals on the actual application surface to assure the function of the “void” message.
Dispensing
As care should be taken not to disturb the tamper-indicating feature by pre-destructing
the “void” message when manually removing the label from the liner, slowly remove the
liner from the label at a 90° angle. It is recommended that the user test samples for each
roll of label seals by laminating a representative label seal to the specific application
surface to assure its function meets expectations. This test can be run after 10 minutes
dwell; however, final judgement should be based on 72 hours dwell at room temperature
prior to testing.
Application
The tamper-indicating mechanism (i.e. the “void” message both on the facestock and
on the substrate) depends upon adequate adhesion of the label to the substrate. A
sufficient bond may not develop on all surfaces due to low surface energy (e.g. PTFE),
contaminated or textured surfaces. Therefore, it is important to determine the
suitability of the product in the intended application by carefully pretesting. The
primary function of the products is to effect a non-transferable (non-reusable) label
seal by causing the “void” message to appear on the facestock when removal from the
substrate is attempted. As a result of the primary function, a “void” message is also
transferred to the substrate and can be removed by hand rubbing or by solvent wiping.
Our tamper-indicating product line is designed to indicate tampering by destructing
when an attempt is made to remove the label. Since no tamper-indicating feature is
100% tamper proof, careful consideration must be taken when designing label seals.
When the consequences of tampering could be severe, such as injury or loss of human
life or significant monetary loss, these products are not recommended as the sole
means of package or product tamper indication. In these instances, additional methods
in combination with the labels should be considered so that the tamper-indicating
features are commensurate with the requirements of the application.
-3-
3M
™
Void Polyester Label Products
FMV02 • FMV12 • FMV22 • FMV32 • FMV0E
Storage Conditions
Store under normal conditions of 70°F (21°C) and 50% relative humidity. To
minimize the effects of humidity on the products, package the die-cut and printed
stock in polyethylene bags. Low density polyethylene (2-4 mils) can help prevent
humidity penetration.
Shelf Life
To obtain best performance, use this product within two years from the date of
manufacture.
Product Use
All statements, technical information and recommendations contained in this document are based upon
tests or experience that 3M believes are reliable. However, many factors beyond 3M’s control can affect
the use and performance of a 3M product in a particular application, including the conditions under
which the product is used and the time and environmental conditions in which the product is expected to
perform. Since these factors are uniquely within the user’s knowledge and control, it is essential that the
user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the
user’s method of application.
Warranty and
Limited Remedy
Unless stated otherwise in 3M’s product literature, packaging inserts or product packaging for individual
products, 3M warrants that each 3M product meets the applicable specifications at the time 3M ships the
product. Individual products may have additional or different warranties as stated on product literature,
package inserts or product packages. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF
DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the 3M product
is fit for a particular purpose and suitable for user’s application. If the 3M product is defective within the
warranty period, your exclusive remedy and 3M’s and seller’s sole obligation will be, at 3M’s option, to
replace the product or refund the purchase price.
Limitation of Liability
Except where prohibited by law, 3M and seller will not be liable for any loss or damage arising from the
3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory
asserted, including warranty, contract, negligence or strict liability.
ISO 9001: 2000
This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards.
3
Industrial Business
Converter Markets
Industrial Adhesives and Tapes Division
1030 Lake Road
Medina, OH 44256-0428
800-422-8116 • 877-722-5072 (fax)
www.3M.com/converter
Recycled Paper
40% pre-consumer
10% post-consumer
3M is a trademark of 3M Company.
Printed in U.S.A.
©3M 2007 70-0711-1084-8
(2/07)
-4-
京公网安备 11010802033920号
EEWORLD
