EEWORLDEEWORLDEEWORLD

Part Number

Search

KMM400VN150M35S

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 150uF, Through Hole Mount, CAN
CategoryPassive components    capacitor   
File Size74KB,4 Pages
ManufacturerNIPPON CHEMI-CON
Websitehttp://www.chemi-con.co.jp
Download Datasheet Parametric View All

KMM400VN150M35S Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 150uF, Through Hole Mount, CAN

KMM400VN150M35S Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerNIPPON CHEMI-CON
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
capacitance150 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.73485 mA
Manufacturer's serial numberKMM
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package shapeCYLINDRICAL PACKAGE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)400 V
ripple current800 mA
surface mountNO
Delta tangent0.15
Terminal shapeSNAP-IN
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Upgrade!
KMM
@Downsize,
longer life, and high ripple version of KMH series
@Load
life with ripple current : 105C 2000 to 3000 hours
@Non-solvent
proof type
Downsized snap-ins 105C
downsized
longer life
KMH
?SPECIFICATIONS
Items
Operating
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Load Life
-25 to +105C
160 to 450V
dc
P20%
(M)
I[3 CV
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
160 to 400V 420 & 450V
Rated Voltage (V
dc
)
0.15
0.20
tanE (Max.)
160 to 400V 420 & 450V
Rated Voltage (V
dc
)
4
8
Z(-25C)/Z(+20C)
Characteristics
(at 20C, 120Hz)
(at 20C after 5 minutes)
(at 20C, 120Hz)
Shelf Life
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the maximum
ripple current is applied for 3000 hours (2000 hours for
F20mm
products) at 85C.
Capacitance change
[P20%
of the initial value
DF (tanE)
[200%
of the initial specified value
Leakage current
[The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C
without voltage applied.
[P15%
of the initial value
Capacitance change
DF (tanE)
[150%
of the initial specified value
Leakage current
[The
initial specified value
?DIMENSIONS
[mm]
@Terminal
type : VS (F20 to
F35)
Sleeve
FD+1max.
Negative mark
@Terminal
type : VN (F22 to
F35)
pc board pin-out
FD+1max.
Sleeve
Negative mark
pc board pin-out
2-F2
LP2
10
2-F2
LP2
5.8P1
10
Vent
*
4.0P0.5
Vent
*
FD=35mm
: 3.5P0.5mm
@Terminal
type : LI (F35)
Sleeve
FD+1max.
Negative mark
4.2P0.5
pc board pin-out
2-1.2B6
@Terminal
type : LC (F20B30 to 50L,
F22B30
to 50L)
(Substandard)
Sleeve
Negative mark
pc board pin-out
2-F2
5P0.5
LP2
4.5P1
14.2P1
FD+1max.
8
LP2
3P1
8P1
1.5P0.1
Vent
Vent
?PART
NUMBERING SYSTEM
KMM 160
VS
1000
M
22F
Case code
Cap tolerance (P20%)
Nominal cap in
MF
Terminal type (VS, VN, LI or LC)
Rated voltage in volts
Series name
Impedance matching and the basic principles of the Smith chart
[size=4] When dealing with practical application problems of RF systems, there are always some very difficult tasks, and matching the different impedances of the cascaded circuits is one of them. In g...
Jacktang RF/Wirelessly
Please help me analyze this circuit.
I would like to ask how to calculate the two resistance values of resistance Rg and resistance Rgs, and also how to choose the temperature fuse, what current and temperature value should be selected?...
lc198818 Analog electronics
Coding for SSDs – Part 1: Introduction and Table of Contents
[i=s] 本帖最后由 白丁 于 2015-11-21 16:10 编辑 [/i][b]转自[url]http://codecapsule.com/2014/02/12/coding-for-ssds-part-1-introduction-and-table-of-contents/[/url]Introduction[/b]I want to make solid-state drives (...
白丁 FPGA/CPLD
How to use the new version of single bus driver and DS18x20
The new version of mpy has made significant changes to the single bus driver, making the previous programs unusable. Even if you use the old DS18X20 driver, it cannot be used under the new firmware. H...
dcexpert MicroPython Open Source section
【Repost】Understand the output of switching regulators to speed up power supply design
[align=left][color=rgb(51, 51, 51)][font=Avenir, "][size=14px]Introduction[/size][/font][/color][/align][align=left][color=rgb(51, 51, 51)][font=Avenir, "][size=14px]Minimizing the output ripple and t...
皇华Ameya360 Integrated technical exchanges
The computer automatically restarts
Whenever I compile a Nios project, my computer restarts automatically. There are no other problems. What's the reason?... Urgent. . . . . . . . . . . . . . . . . . . ....
mu03029827 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1176  261  2536  2448  2018  24  6  52  50  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号