Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
TTL compatible inputs and output levels, three-state
bidirectional data bus
Typical radiation performance
- Total dose: 50krads
- SEL Immune 110 MeV-cm
2
/mg
- SEU LET
TH
(0.25) = 52 cm
2
MeV
- Saturated Cross Section 2.8E-8 cm
2
/bit
-<1.1E-9 errors/bit-day, Adams 90% worst case
environment geosynchronous orbit
Packaging:
- 36-lead ceramic flatpack (3.831 grams)
Standard Microcircuit Drawing 5962-00536
- QML Q and V compliant part
INTRODUCTION
The UT9Q512E RadTolerant product is a high-performance
CMOS static RAM organized as 524,288 words by 8 bits. Easy
memory expansion is provided by an active LOW Chip Enable
(E), an active LOW Output Enable (G), and three-state drivers.
Writing to the device is accomplished by taking Chip Enable (E)
input LOW and Write Enable (W) inputs LOW. Data on the eight
I/O pins (DQ
0
through DQ
7
) is then written into the location
specified on the address pins (A
0
through A
18
). Reading from
the device is accomplished by taking Chip Enable (E) and
Output Enable (G) LOW while forcing Write Enable (W) HIGH.
Under these conditions, the contents of the memory location
specified by the address pins will appear on the I/O pins.
The eight input/output pins (DQ
0
through DQ
7
) are placed in a
high impedance state when the device is deselected (E HIGH),
the outputs are disabled (G HIGH), or during a write operation
(E LOW and W LOW).
Clk. Gen.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Pre-Charge Circuit
Row Select
Memory Array
1024 Rows
512x8 Columns
I/O Circuit
Column Select
Data
Control
CLK
Gen.
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ
0
- DQ
7
E
W
G
Figure 1. UT9Q512E SRAM Block Diagram
1
DEVICE OPERATION
A0
A1
A2
A3
A4
E
DQ0
DQ1
V
DD
V
SS
DQ2
DQ3
W
A5
A6
A7
A8
A9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
The UT9Q512E has three control inputs called Chip Enable (E),
Write Enable (W), and Output Enable (G); 19 address inputs,
A(18:0); and eight bidirectional data lines, DQ(7:0). E controls
device selection, active, and standby modes. Asserting E enables
the device, causes I
DD
to rise to its active value, and decodes the
19 address inputs to select one of 524,288 words in the memory.
W controls read and write operations. During a read cycle, G
must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
1
0
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. UT9Q512E 20ns SRAM Pinout (36)
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD
V
SS
Address
Data Input/Output
Chip Enable
Write Enable
Output Enable
Power
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min) and E less than V
IL
(max) defines a read cycle. Read access time is measured from
the latter of Chip Enable, Output Enable, or valid address to
valid data output.
SRAM Read Cycle 1, the Address Access in figure 4a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as Chip
Enable and Output Enable are active, the address inputs may
change at a rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable - Controlled Access in
figure 4b, is initiated by E going active while G remains asserted,
W remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable - Controlled Access in
figure 4c, is initiated by G going active while E is asserted, W
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable - Controlled Access in figure
5a, is defined by a write terminated by W going high, with E
still active. The write pulse width is defined by t
WLWH
when the
write is initiated by W, and by t
ETWH
when the write is initiated
by E. Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable - Controlled Access in figure
5b, is defined by a write terminated by E going inactive. The
write pulse width is defined by t
WLEF
when the write is initiated
by W, and by t
ETEF
when the write is initiated by the E going
active. For the W initiated write, unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the eight bidirectional
pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
Table 2. Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1.1E-9
krad(Si)
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. Adam’s 0% worst case environment, Geosynchronous orbit, 100 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to 7.0V
-65 to +150°C
1.0W
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
4.5 to 5.5V
(C) screening: -55°C to +125°C
(W) screening: -40°C to +125°C
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
-55°C to +125°C for (C) screening and -40
o
C to +125
o
C for (W) screening (V
DD
= 5.0V + 10%)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
(TTL)
(TTL)
I
OL
= 8mA, V
DD
=4.5V (TTL)
I
OL
= 200μA,V
DD
=4.5V (CMOS)
I
OH
= -4mA,V
DD
=4.5V (TTL)
I
OH
= -200μA,V
DD
=4.5V (CMOS)
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
IN
= V
DD
and V
SS,
V
DD
= V
DD
(max)
V
O
= V
DD
and V
SS
V
DD
= V
DD
(max)
G = V
DD
(max)
V
DD
= V
DD
(max), V
O
= V
DD
V
DD
= V
DD
(max), V
O
= 0V
I
DD
(OP)
4
Supply current operating
@ 1MHz
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
I
OUT
= 0mA
E = V
DD
- 0.5
V
DD
= V
DD
(max)
V
IH
= V
DD
- 0.5V
-55°C, -40°C, 25°C
125°C
50
mA
-2
-2
2.4
3.2
10
12
2
2
CONDITION
MIN
2
0.8
0.4
0.05
MAX
UNIT
V
V
V
V
V
V
pF
pF
μA
μA
I
OS2, 3
Short-circuit output current
-90
90
mA
I
DD
(OP)
4
Supply current operating
@50MHz
76
mA
I
DD
(SB)
Supply current standby
@0MHz
10
45
mA
mA
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019.
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
About embedded systems - dedicated to beginners who love this field. Preface I have seen many netizens asking many questions about embedded systems on the Internet. Many of them can be answered here. ...
[i=s] This post was last edited by bqgup on 2019-4-12 21:24 [/i] [postbg]3.jpg[/postbg] [font=黑体][size=4] The external clock of the board I use is 50MHz, and the clock pin is PIN_23. The on and off st...
As we all know, the templates in MDK are very useful, but I don't know where the templates defined in templates are stored. Can I build a template library to share with others? It would be even better...
Back up the TF card of the Android system in the tmdxevm3358-sk kit, format it to FAT32, and install StarterWare 02.00.00.07. Something went wrong during the formatting process. WINDOWS cannot complet...
A design of X-band direct frequency synthesizer is introduced, its output spurious signal is analyzed, and the development results are given. At the output frequency of 10GHz, the phase noise at 1kHz ...
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
Have you ever heard stories about "crazy appliances"? Think of microwaves that turn on automatically or ovens that preheat without any human input? With radios and electromagnetic interfaces ubiqui...[Details]
Based on the commutation technology, thyristor rectifiers are classified into two main types. Line-commutated and force-commutated inverters are commonly used, while other commutated inverters, nam...[Details]
My career has been closely tied to the semiconductor industry. From product management to content marketing, I've provided countless forecasts and predictions across a variety of roles. Whethe...[Details]
From time to time, I see some audiophiles spending a lot of money or a lot of time to DIY speakers, but the results are not what they want. Below I list some of the small experiences I summarized b...[Details]
With the continuous development of ultrasonic technology, ultrasound has been widely used in fields such as inspection, cleaning, welding, and medical treatment, and has even found its way into tex...[Details]
According to foreign media reports, German chipmaker Infineon has recently completed the acquisition of Marvell Technology's automotive Ethernet business for a total transaction amount of US$2.5 bi...[Details]
Siemens software mainly includes PLC, frequency converter, human-machine interface, etc. The current Siemens software can be said to be very stable.
PLC series range from the Siemens S5 series...[Details]
A graphics processor (GPU), also known as a display core, visual processor, or display chip, is a microprocessor specialized for image processing on personal computers, workstations, game consoles,...[Details]
When a self-driving car is traveling straight ahead on the road and a vehicle ahead or in an adjacent lane is about to turn left, the system must make a quick and accurate judgment within the compl...[Details]
Charging is essential for electric vehicles. It's crucial for battery safety and range. When it comes to charging new energy vehicles, is it better to charge when the battery is almost empty, or to...[Details]
Why do automotive electronic circuit boards require reliability cleaning? Among the various electronic circuit boards that implement various functions, which ones require cleaning and which ones do...[Details]
The World Conference (WC 2025) recently opened in Shanghai. This year's event, covering over 70,000 square meters for the first time, attracted over 800 exhibitors, showcasing large models, AI term...[Details]
In 2013, the introduction of fingerprint recognition in the Apple iPhone 5S sparked a craze for fingerprint phones. The Android-based Huawei Mate 7 also became a hit thanks to its fingerprint recog...[Details]
Talking about work
京公网安备 11010802033920号
EEWORLD
