5GSR64-E-100N-FREQ datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 5GSR64-E-100N-FREQ

5GSR64-E-100N-FREQ: DescriptionSine Output Oscillator, 10MHz Min, 30MHz Max, SMD, 6 PIN; CategoryPassive components oscillator; File Size95KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/

Download Datasheet Parametric View All

5GSR64-E-100N-FREQ Overview

Sine Output Oscillator, 10MHz Min, 30MHz Max, SMD, 6 PIN

5GSR64-E-100N-FREQ Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	Euroquartz
Reach Compliance Code	compliant
Other features	ENABLE/DISABLE FUNCTION
Maximum control voltage	4.5 V
Minimum control voltage	0.5 V
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	100 ppm
frequency stability	50%
Installation features	SURFACE MOUNT
Maximum operating frequency	30 MHz
Minimum operating frequency	10 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	SINE
Output impedance	10000 Ω
Output level	1 V
physical size	11.4mm x 9.6mm x 2.5mm
Maximum supply voltage	5.25 V
Minimum supply voltage	4.75 V
Nominal supply voltage	5 V
surface mount	YES

Preview

Download Datasheet

View All

EURO

QUARTZ

FEATURES

Sine Wave output VCXO

Output 10k //10pF load, 1.0V p-p

Harmonics < 25dBc

Low current consumption

DESCRIPTION

GSR64 sine wave VCXOs provide a true sine wave out output. The

VCXOs are packaged in the industry-standard, 6 pad 11.4 x 9.6mm

SMD package. The VCXO is produced to close tolerances and has low

current consumption.

GSR64 Sine Wave VCXOs

11.4 x 9.6 x 4.7mm SMD Sine Wave VCXO

OUTLINE & DIMENSIONS

SPECIFICATION

Frequency Range:

Input Voltage:

Frequency Stability:

Control Voltage Centre:

Initial Frequency Accuracy:

Control Voltage Range:

Frequency Deviation Range:

Output Wave Form:

Output Level:

Harmonics:

Phase Noise:

Current Consumption

Supply = 2.8V:

Supply = 3.3V:

Supply = 5.0V:

Start-up Time:

Storage Temperature:

Sub-Harmonics:

Ageing:

Enable/Disable:

10.0MHz to 30.0MHz

+2.8V, +3.3V±5% or +5.0VDC ±5%

See table

+2.5 VDC

±15ppm with Conrol V at +2.5VDC

+0.5V to +4.5VDC

±100ppm typical*

True Sine Wave

10k //10pF load, 1.0V p-p

<-25dBc

-130dBc/Hz at 1kHz offset

1.0mA

1.1mA

1.2mA

2.0ms typical

-50° to +125°C

None

±5ppm per year maximum

Output is high impedance (disabled)

when E/D pad/pin is taken LOW.

Disable time is 150ns maximum

Fully compliant

RoHS Status:

* Wider pulling range available

FREQUENCY STABILITY

Stability Code Stability ±ppm Temp. Range

0°~+70°C

100

0°~+70°C

-40°~+85°C

100

-40°~+85°C

If non-standard frequency stability is required

Use ‘I’ followed by stability, i.e. I20 for ±20ppm

PART NUMBERING

Example:

Supply Voltage

3 = 3.3 Volts

5 = 5.0 Volts

Series Designation

GSR64

RoHS Status

G = compliant

Blank = non-compliant

Frequency Stability

See table

Pull Range

±ppm

Pull Range Code

M = Maximum

N = Minimum

T = Typical

Frequency

MHz

3GSR64G-A-80N-25.000

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk

Recommended Resources

Natural gas (gas) stove flameout alarm

Speed regulation by connecting resistors in series in the excitation circuit

Simple TTL delay circuit (3) circuit diagram

Aimijia’s 2-in-1 remote control circuit, NOKIA and PHILIPS

Computer motherboard circuit diagram 440BX_27

Research and development of insulation performance of automotive electrical appliances: Introduces the basic structure, usage, characteristics, etc. of the automotive electrical insulation performance test bench...; frozenviolet Automotive Electronics

How to realize PWM waveform output in altera FPGA: No IP core is provided. I see that all the IP cores on the Internet are written by myself. Can the timer IP core be realized? The timer of stm32 can realize PWM, but I don’t know how FPGA realizes it....; tianma123 FPGA/CPLD

What tools do you use to read and write the internal EEPROM of the STC microcontroller?: This STC microcontroller has an EEPROM inside, and the capacity is not small, which is quite unique among 51 microcontrollers. I wanted to use it recently, but I couldn't find a suitable programmer fo...; 古道热肠 MCU

【DIY Handheld Signal Generator】AD9834 Introduction: :loveliness: AD9834 is a low-power DDS device from ADI, which can output high-performance sine waves, triangle waves and square waves. The output frequency and initial phase can be set by software pro...; eeleader ADI Reference Circuit

What are the emulators suitable for MSP430F149?: There is one that costs more than 100 yuan, which seems quite expensive. If you just want to see the registers, pin levels and variable values when the microcontroller is running, do you have to use t...; 非你不娶 Microcontroller MCU

Electronic technology capabilities of foreign vehicle manufacturers (zt): The main reason for writing this article is that I was repeatedly ravaged by their specifications. Let's talk about Ford first. When I read Ford's general requirements for body control modules ELCOMV1...; wljmm Automotive Electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components