EN25F10-100GIP datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> storage> EN25F10-100GIP

EN25F10-100GIP: Description1 Megabit Serial Flash Memory with 4Kbytes Uniform Sector; Categorystorage storage; File Size1MB，32 Pages; ManufacturerEon; Websitehttp://www.essi.com.tw/; Environmental Compliance

Download Datasheet Parametric Compare View All

EN25F10-100GIP Overview

1 Megabit Serial Flash Memory with 4Kbytes Uniform Sector

EN25F10-100GIP Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Eon
package instruction	0.150 INCH, ROHS COMPLIANT, SOP-8
Reach Compliance Code	unknow
Maximum clock frequency (fCLK)	100 MHz
Durability	100000 Write/Erase Cycles
JESD-30 code	R-PDSO-G8
length	4.9 mm
memory density	1048576 bi
Memory IC Type	FLASH
memory width	8
Number of functions	1
Number of terminals	8
word count	131072 words
character code	128000
Operating mode	SYNCHRONOUS
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
organize	128KX8
Package body material	PLASTIC/EPOXY
encapsulated code	SOP
Encapsulate equivalent code	SOP8,.25
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Parallel/Serial	SERIAL
power supply	3/3.3 V
Programming voltage	2.7 V
Certification status	Not Qualified
Maximum seat height	1.75 mm
Serial bus type	SPI
Maximum standby current	0.000005 A
Maximum slew rate	0.025 mA
Maximum supply voltage (Vsup)	3.6 V
Minimum supply voltage (Vsup)	2.7 V
Nominal supply voltage (Vsup)	3 V
surface mount	YES
technology	CMOS
Temperature level	INDUSTRIAL
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	DUAL
type	NOR TYPE
width	3.9 mm
write protect	HARDWARE/SOFTWARE

Preview

Download Datasheet

View All

EN25F10

Purpose

Eon Silicon Solution Inc. (hereinafter called “Eon”) is going to provide its products’ top marking on

ICs with < cFeon > from January 1st, 2009, and without any change of the part number and the

compositions of the ICs. Eon is still keeping the promise of quality for all the products with the

same as that of Eon delivered before. Please be advised with the change and appreciate your

kindly cooperation and fully support Eon’s product family.

Eon products’ New Top Marking

cFeon Top Marking Example:

cFeon

Part Number: XXXX-XXX

Lot Number: XXXXX

Date Code:

XXXXX

Continuity of Specifications

There is no change to this data sheet as a result of offering the device as an Eon product. Any

changes that have been made are the result of normal data sheet improvement and are noted in

the document revision summary, where supported. Future routine revisions will occur when

appropriate, and changes will be noted in a revision summary.

Continuity of Ordering Part Numbers

Eon continues to support existing part numbers beginning with “Eon” and “cFeon” top marking. To

order these products, during the transition please specify “Eon top marking” or “cFeon top marking”

on your purchasing orders.

For More Information

Please contact your local sales office for additional information about Eon memory solutions.

This Data Sheet may be revised by subsequent versions

or modifications due to changes in technical specifications.

www.eonssi.com

Rev. E, Issue Date: 2010/05/25

EN25F10

SIGNAL DESCRIPTION

Serial Data Input (DI)

The SPI Serial Data Input (DI) pin provides a means for instructions, addresses and data to be serially

written to (shifted into) the device. Data is latched on the rising edge of the Serial Clock (CLK) input pin.

Serial Data Output (DO)

The SPI Serial Data Output (DO) pin provides a means for data and status to be serially read from

(shifted out of) the device. Data is shifted out on the falling edge of the Serial Clock (CLK) input pin.

Serial Clock (CLK)

The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See

SPI Mode")

Chip Select (CS#)

The SPI Chip Select (CS#) pin enables and disables device operation. When CS# is high the device is

deselected and the Serial Data Output (DO) pin is at high impedance. When deselected, the devices

power consumption will be at standby levels unless an internal erase, program or status register cycle is

in progress. When CS# is brought low the device will be selected, power consumption will increase to

active levels and instructions can be written to and data read from the device. After power-up, CS# must

transition from high to low before a new instruction will be accepted.

Hold (HOLD#)

The HOLD pin allows the device to be paused while it is actively selected. When HOLD is brought low,

while CS# is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be

ignored (don’t care). The hold function can be useful when multiple devices are sharing the same SPI

signals.

Write Protect (WP#)

The Write Protect (WP#) pin can be used to prevent the Status Register from being written. Used in

conjunction with the Status Register’s Block Protect (BP0, BP1 and BP2) bits and Status Register

Protect (SRP) bits, a portion or the entire memory array can be hardware protected.

Table 1. PIN Names

Symbol

CLK

CS#

WP#

HOLD#

Vcc

Vss

Pin Name

Serial Clock Input

Serial Data Input

Serial Data Output

Chip Enable

Write Protect

Hold Input

Supply Voltage (2.7-3.6V)

Ground

This Data Sheet may be revised by subsequent versions

or modifications due to changes in technical specifications.

www.eonssi.com

Rev. E, Issue Date: 2010/05/25

EN25F10-100GIP Related Products

	EN25F10-100GIP	EN25F10-100WIP	EN25F10_1
Description	1 Megabit Serial Flash Memory with 4Kbytes Uniform Sector	Flash, 128KX8, PDSO8, 5 X 6 MM, ROHS COMPLIANT, VDFN-8	1 Megabit Serial Flash Memory with 4Kbytes Uniform Sector

Recommended Resources

timer exposure circuit

High-efficiency switching power supply circuit diagram with 300V output

Small FM transmitter circuit

555 Ding Dong audio electronic doorbell circuit

Single control regulated power supply 2

The self-made 51 microcontroller development board is not completely powered off by PL2303! Experts, please take a look!: The self-made 51 microcontroller development board is not completely powered off by PL2303! Experts, please take a look!PL2303 circuit diagram:Power supply:Fault phenomenon: After connecting the USB i...; kyb小黑 51mcu

Use the serial port assistant to send decimal numbers to the microcontroller and display them on the digital tube: How do I write it? It's messy....; ELEGIE MCU

Nokia5110 LCD Driver (XS128): [i=s] This post was last edited by paulhyde on 2014-9-15 09:13 [/i] I referred to the Nokia5110 LCD driver on the Internet and ported one to MC9S12XS128. Welcome to communicate~~...; bdc90 Electronics Design Contest

Application of EXCEL in Mine Surveying: I bought the software "Theodolite Wire Measurement Calculation Book" from [email=mjylyh1111@163.com]mjylyh1111@163.com[/email] and it is very useful and has been well received by the unit! They also g...; seawolf Test/Measurement

If Intel approves, the cost of ultra-thin notebooks will drop to the $200 range: [color=#000][font=Arial, Helvetica, sans-serif, 瀹嬩綋][size=14px]With prices of ultrabooks now above $600, can manufacturers offer such products for $200? According to IHS's PC Market Brief, the answer ...; wstt Mobile and portable

Urgently needed!!! Plan!!! Arm cooperation!!!: [font=宋体][size=10pt]Urgently needed!!! [/size][/font][font=Arial][size=10pt] [/size][/font][font=宋体][size=10pt]Electronic technology R&D design and development plan!!! [/size][/font][font=Arial][size=...; ningyiong ARM Technology

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components