RPS-160_12 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > RPS-160_12

Preview

RPS-160_12: Description160W Single Output Medical Type; File Size400KB，2 Pages; ManufacturerMEAN WELL; Websitehttp://www.meanwell.com

Download Datasheet Compare View All

RPS-160_12 Overview

160W Single Output Medical Type

Preview

Download Datasheet

View All

160W Single Output Medical Type

Features :

RPS-160

Universal AC input / Full range

Built-in active PFC function

series

Protections: Short circuit / Overload / Over voltage / Over temperature

5"x3" compact size

Free air convection for 110W and 160W with 20.5 CFM forced air

With power good and fail signal output

Built-in remote sense function for 5~15V

No load power consumption under 0.75W by PS-ON control

(G model)

Standby 5V@0.8A with fan, @0.6A without fan (G model)

3 years warranty

RPS G

G: With 5Vsb & no load power

consumption < 0.75 W

Blank: Basic function (without 5Vsb)

160

SPECIFICATION

MODEL

DC VOLTAGE

RPS -160-5

RATED CURRENT (20.5CFM)

30A

CURRENT RANGE (convection)

0 ~ 20A

CURRENT RANGE (20.5CFM)

0 ~ 30A

RATED POWER (convection)

Note.7

103W

RATED POWER (20.5CFM)

Note.8

155W

OUTPUT

RIPPLE & NOISE (max.)

Note.2

100mVp-p

VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

FREQUENCY RANGE

POWER FACTOR (Typ.)

INPUT

EFFICIENCY (Typ.)

AC CURRENT (Typ.)

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVERLOAD

OVER VOLTAGE

PROTECTION

OVER TEMPERATURE

CH1:4.5 ~ 5.5V

VOLTAGE TOLERANCE

Note.3

4.0%

0.5%

1.0%

1800ms, 30ms/230VAC

Note.6

90 ~ 264VAC

RPS -160-12

12V

12.9A

0 ~ 9.1A

0 ~ 12.9A

112.2W

159.8W

100mVp-p

CH1:10.8 ~ 13.2V

3.0%

0.5%

1.0%

RPS -160-15

15V

10.3A

0 ~ 7.3A

0 ~ 10.3A

112.5W

159.5W

120mVp-p

CH1:13.5 ~ 16.5V

3.0%

0.5%

1.0%

RPS -160-24

24V

6.5A

0 ~ 4.6A

0 ~ 6.5A

113.4W

161W

150mVp-p

CH1:22 ~ 27V

2.0%

0.5%

1.0%

RPS -160-48

48V

3.25A

0 ~ 2.3A

0 ~ 3.25A

113.4W

161W

250mVp-p

CH1:43.2 ~ 52.8V

2.0%

0.5%

1.0%

3500ms, 30ms/115VAC at full load

16ms/230VAC/115VAC at full load

127 ~ 370VDC

PF>0.98/115VAC at full load

87%

88%

47 ~ 63Hz

PF>0.93/230VAC

85%

2A/115VAC

1.1A/230VAC

COLD START 35A/115VAC

70A/230VAC

Earth leakage current <300uA / 264VAC, patient leakage current <100uA/264VAC

105 ~ 135% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

5.75 ~ 6.75V

13.8 ~ 16.2V

17.25 ~ 20.25V

27.6 ~ 32.4V

55.2 ~ 64.8V

Protection type : Shut down o/p voltage, re-power on to recover

110 (5V),105 (12V,15V,24V,48V) (TSW1 : detect on heatsink of power transistor)

(5V),90

(12V,15V,24V,48V) (TSW2 : detect on heatsink of power transistor)

Protection type : (TSW1)Shut down o/p voltage, recovers automatically after temperature goes down

Protection type : (TSW2)Shut down o/p voltage, re-power on to recover

5VSB : 5V@0.6A without fan, 0.8A with fan 20.5CFM ; tolerance 2%, ripple : 50mVp-p(max.)

5V STANDBY (G model)

FUNCTION

PS-ON INPUT SIGNAL (G model)

Power on: PS-ON = "Hi" or " > 2 ~ 5V" ; Power off: PS-ON = "Low" or " < 0 ~ 0.5V"

PF>1ms

POWER GOOD / POWER FAIL

500ms>PG>10ms

5 ~ 15V

REMOTE SENSE

-20 ~ +70

(Refer to "Derating Curve")

WORKING TEMP.

WORKING HUMIDITY

ENVIRONMENT STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS

SAFETY & WITHSTAND VOLTAGE

ISOLATION RESISTANCE

EMC

(Note 4)

EMC EMISSION

20 ~ 90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH

0.03%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

ANSI/AAMI ES60601-1,

TUV EN60601-1 approved

I/P-O/P:4KVAC

I/P-FG:1.5KVAC

O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH

Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A

230.5Khrs min. MIL-HDBK-217F (25 )

127*76.2*34.6mm (L*W*H)

0.32Kg; 36pcs/12.5Kg/0.79CUFT

EMC IMMUNITY

MTBF

OTHERS

DIMENSION

PACKING

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.

(as available on http://www.meanwell.com)

5. HS1,HS2 & HS3 can not be shorted.

6. Derating may be needed under low input voltages. Please check the derating curve for more details.

7. The rated power includes 5Vsb @ 0.6A.

8. The rated power includes 5Vsb @ 0.8A.

RPS-160_12 Related Products

	RPS-160_12	RSP-160-12	RSP-160-15	RSP-160-24	RSP-160-48	RSP-160-5
Description	160W Single Output Medical Type	160W Single Output Medical Type	160W Single Output Medical Type	160W Single Output Medical Type	160W Single Output Medical Type	160W Single Output Medical Type

Recommended Resources

Mechanical power slide control circuit with reverse working feed

New ZTE GDH-20 manual reset motor protection circuit

Simple sine oscillator

555 constitutes a multivibrator circuit diagram with adjustable duty cycle

Tips for selecting inductors in switching power supplies: Selection of inductor in switching power supply 　　What is an inductor? And its characteristics 　　Inductors are commonly used components in switching power supplies. Since their current and voltage pha...; Jacktang Energy Infrastructure?

How to make WinC support AMR audio format (Directshow): As title...; yinwei2005 Embedded System

How to adjust the frequency duty cycle in the RCC circuit: How to adjust the frequency duty cycle in the RCC circuit? Thank you for your advice, thank you very much...; xin Power technology

There is no SDI input. Could it be a problem with the DSP encoder board?: There is no SDI input after a board is connected to the machine. Could you tell me what is the cause? Thank you! ! :)...; 红颜添乱 DSP and ARM Processors

Discussion on full screen dialog box under CE???: // Hide input panel SIPINFO si; memset(&si, 0, sizeof(SIPINFO)); si.cbSize = sizeof(SIPINFO); SHSipInfo(SPI_GETSIPINFO, 0, &si, 0); if (si.fdwFlags & SIPF_ON) { si.cbSize = sizeof(SIPINFO); si.fdwFlag...; coffeewjf Embedded System

[AN-1165 Application Note] Operational Amplifiers for MEMS Microphone Preamplifier Circuits: Introduction: Microphone preamplifier circuit is used to amplify the output signal of the microphone to match the input level of the subsequent device in the signal chain....; EEWORLD社区 ADI Reference Circuit

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components