• 350 Watts Peak Pulse Power per Line(tp = 8/20µs)
• Monolithic Design
• Protects 4 Lines
• Unidirectional & Bidirectional Configurations
• ESD Protection > 25 kilovolts
• Low Clamping Voltage
• Low Leakage Current
• Avaiable in Multiple Voltages
• RoHS Compliant
• REACH Compliant
APPLICATIoNS
• SMART Phones
• Portable Electronics
• FireWire, Ethernet and USB Interfaces
MEChANICAL ChARACTERISTICS
•
•
•
•
Molded JEDEC SOT-23-6 Package
Approximate Weight: 16 milligrams
Lead-Free Pure-Tin Plating (Annealed)
Solder Reflow Temperature:
Pure-Tin - Sn, 100: 260-270°C
• Flammability Rating UL 94V-0
• 8mm Tape and Reel per EIA Standard 481
PIN CoNFIGURATIoNS
1
2
3
6
5
4
1
2
3
BIDIRECTIONAL
6
5
4
UNIDIRECTIONAL
05132.R8 10/12
Page 1
www.protekdevices.com
05132
Only One Name Means ProTek’Tion™
SMS05 - SMS24C
TYPICAL DEVICE ChARACTERISTICS
MAXIMUM RATINGS
@ 25°C Unless otherwise Specified
PARAMETER
Peak Pulse Power (tp = 8/20µs) - See Figure 1
Operating Temperature
Storage Temperature
SYMBoL
P
PP
T
L
T
STG
VALUE
350
-55 to 150
-55 to 150
UNITS
Watts
°C
°C
ELECTRICAL ChARACTERISTICS PER LINE
@ 25°C Unless otherwise Specified
PART
NUMBER
(Notes 1-3)
DEVICE
MARkING
RATED
STAND-oFF
VoLTAGE
V
WM
VoLTS
SMS05
SMS05C
SMS12
SMS12C
SMS15
SMS15C
SMS24
SMS24C
1.
2.
3.
4.
MINIMUM
BREAkDoWN
VoLTAGE
@ 1mA
V
(BR)
VoLTS
6.0
6.0
13.3
13.3
16.7
16.7
26.7
26.7
MAXIMUM
CLAMPING
VoLTAGE
(Fig. 2)
@ I
P
= 1A
V
C
VoLTS
9.8
9.8
19.0
19.0
24.0
24.0
40.0
40.0
MAXIMUM
LEAkAGE
CURRENT
@V
WM
I
D
µA
20
20
1
1
1
1
1
1
TYPICAL
CAPACITANCE
(Note 4)
@0V, 1Mhz
Cj
pF
150
150
80
80
50
50
40
40
PRH
PRL
PRI
PRM
PRJ
PRN
PRK
PRO
5.0
5.0
12.0
12.0
15.0
15.0
24.0
24.0
NoTES
Part numbers with an additional “C” suffix are bidirectional, i.e., SMS05C.
Unidirectional Only: For SMSxx, test between pin 1 to 2 or 5, 4 to 2 or 5, 6 to 2 or 5, 3 to 2 or 5. For SMSxxC, test between 2 to 1, 3, 4, 5, or 6.
Bidirectional Only: For SMSxxC, test between pin 5 to 1 or 3 or 4 or 6. Electrical characteristics apply in both directions.
Unidirectional Only: For SMSxx, capacitance measured between pins 1, 3, 4, 6 to 2. For SMSxxC, capactiance measured between pins 2 to 1, 3, 4, 5, or 6.
05132.R8 10/12
Page 2
www.protekdevices.com
05132
Only One Name Means ProTek’Tion™
SMS05 - SMS24C
TYPICAL DEVICE ChARACTERISTICS
FIGURE 1
PEAk PULSE PoWER VS PULSE TIME
10,000
P
PP
- Peak Pulse Power - Watts
1,000
350W, 8/20µs Waveform
100
10
0.1
1
10
100
t
d
- Pulse Duration - µs
1,000
10,000
120
I
PP
- Peak Pulse Current - % of I
PP
FIGURE 2
PULSE WAVE FoRM
t
f
Peak Value I
PP
TEST
WAVEFORM
PARAMETERS
t
f
= 8µs
t
d
= 20µs
100
80
% of Rated Power
FIGURE 3
PoWER DERATING CURVE
Peak Pulse Power
8/20µs
100
80
60
40
20
0
0
5
e
-t
60
40
20
0
Average Power
t
d
= t/(I
PP
/2)
10
15
t - Time - µs
20
25
30
0
25
50
75 100 125
T
A
- Ambient Temperature - °C
150
05132.R8 10/12
Page 3
www.protekdevices.com
05132
Only One Name Means ProTek’Tion™
SMS05 - SMS24C
TYPICAL DEVICE ChARACTERISTICS
FIGURE 4
oVERShooT & CLAMPING VoLTAGE FoR SMS05C
40
30
5 Volts per Division
20
10
0
ESD Test Pulse - 25 kilovolt, 1/30ns (Waveshape)
160
FIGURE 5
TYPICAL REVERSE VoLTAGE VS CAPACITANCE FoR SMS05
C - Capacitance - pF
120
80
40
0
0
1
2
3
4
V
R
- Reverse Voltage - Volts
5
6
05132.R8 10/12
Page 4
www.protekdevices.com
05132
Only One Name Means ProTek’Tion™
SMS05 - SMS24C
APPLICATIoN INFoRMATIoN
Line 1
Line 2
3
I/O Port
2
1
4
5
6
Line 3
Line 4
FIGURE 1 - CoMMoN-MoDE I/o PoRT PRoTECTIoN (UNIDIRECTIoNAL)
Circuit connectivity is as follows:
• Line 1 connected to pin 1.
• Line 2 connected to pin 3.
• Line 3 connected to pin 4.
• Line 4 connected to pin 6.
• Pin 5 connected to ground.
• Pin 6 not connected.
Line 1
Line 2
3
I/O Port
2
1
4
5
6
Line 3
Line 4
FIGURE 1 - CoMMoN-MoDE I/o PoRT PRoTECTIoN (BIDIRECTIoNAL)
Circuit connectivity is as follows:
• Line 1 connected to pin 1.
• Line 2 connected to pin 3.
• Line 3 connected to pin 4.
• Line 4 connected to pin 5.
• Pin 6 connected to ground.
• Pin 2 not connected.
CIRCUIT BoARD RECoMMENDATIoNS
Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended:
• The protection device should be placed near the input terminals or connectors, the device will divert the transient current
immediately before it can be coupled into the nearby traces.
• The path length between the TVS device and the protected line should be minimized.
• All conductive loops including power and ground loops should be minimized.
• The transient current return path to ground should be kept as short as possible to reduce parasitic inductance.
• Ground planes should be used whenever possible. For multilayer PCBs, use ground vias.
[color=#333333][font=tahoma, arial, simsun]I bought it on Taobao at the end of September 2014, but because I was learning other models of single-chip microcomputers, I didn't use it. Brand new! . Comp...
[size=4]:Cry: Another big bad news, 360 Cloud Disk is also going to be closed. ... I'm planning to see if I should buy a hard drive... By the way, do netizens have any recommendations for hard drives?...
A flag to another clock domain
If the signal that needs to cross the clock domains is just a pulse (i.e. it lasts just one clock cycle), we call it a "flag". The previous design usually doesn't work (...
The 50-year evolution of kissing 1. In the 1960s, it was called “that” Female (lowers her head and whispers): Hey, can you “that” me? ! Male (confused) says: That? ! Which one? ! Female (shy) says: “T...
The communications market continues to evolve, and the development of new products is more complex than ever. These creative, innovative solutions rely on engineers to make them a reality. Qorvo under...
ISP devices, such as field programmable devices (FPGAs and CPLDs), do not require a programmer. Using programming kits provided by the device manufacturer, they employ a top-down modular design app...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
Capable of providing precise and efficient thermal management for artificial intelligence computing power, intelligent sensing and autonomous driving systems
Shenzhen, ...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
On August 21, it was reported that Intel's new generation of AI chip Jaguar Shores was recently exposed for the first time.
According to photos shared by Andreas Schilling, the Jaguar Shores t...[Details]
Nascent Micro is launching devices covering a wide range of power applications, including gallium nitride (GaN) drivers, dual-channel automotive drivers, and battery protection MOSFETs.
...[Details]
Traditionally, electrical energy is transmitted primarily through wires, requiring direct physical contact between the power source and the load. With the increasing number of electrical devices in...[Details]
Blackfin® 16-/32-bit embedded processors offer high performance, low power consumption, flexible software features, and scalability, making them suitable for converged applications such as multi-fo...[Details]
The motor is a very important component for new energy vehicles. In terms of vehicle power, pure electric vehicles use electric motors instead of traditional diesel/gasoline engines. For electric v...[Details]
Using an electronic load is like thinking of it as a resistor that dissipates the power supply's output. The most straightforward mode is the CR constant resistance mode. In this mode, by setting a...[Details]
Recently, I received a request to use OK1028A-C to output PWM square wave. However, I found that there was no relevant instructions on the OK1028 platform, so I started writing this article.
A...[Details]
On August 19, Huawei's Executive Director and Chairman of the Device BG, Richard Yu, shared a Weibo post about a conversation he had with a Zunjie S800 owner. The owner had driven over 5,000 kilome...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
