EEWORLDEEWORLDEEWORLD

Part Number

Search

BZV40/E0132/40

Description
Mains Power Connector, 1A, 250V, Female and Male
CategoryThe connector    The connector   
File Size57KB,1 Pages
ManufacturerBULGIN
Websitehttp://www.bulgin.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

BZV40/E0132/40 Overview

Mains Power Connector, 1A, 250V, Female and Male

BZV40/E0132/40 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerBULGIN
Reach Compliance Codecompliant
Connector typeMAINS POWER CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderFEMALE AND MALE
Contact materialNOT SPECIFIED
Coupling typeSNAP
DIN complianceNO
IEC complianceNO
MIL complianceNO
Power Connector Ratings1A, 250V
Manufacturer's serial numberBZV
Installation typePANEL
Total number of contacts6
About CAN interrupt of 8962
I would like to ask you. After my program enters the CAN interrupt, I use CANIntStatus (CAN0_BASE, CANI_INT_STS_CAUSE) to read, but why does it always return "0"? I have read a lot of documents, and d...
ZHANGXUEJIE Microcontroller MCU
TM4C123G cannot simulate TI routine timers. . .
[url] I am a beginner in M4 and want to create a new program by imitating the source program. I found that after setting various paths and predefined symbols, the compilation can pass, but the functio...
nemo1991 Microcontroller MCU
Transfer some new idle development boards, all of them are brand new
[i=s] This post was last edited by fesns on 2014-9-9 20:10 [/i]I am transferring some unused development boards on behalf of a friend. They are all brand new. [b] Transfer a brand new STM32F030R8 DISC...
fesns Buy&Sell
Seek advice from experts
This is the main control diagram of the circuit of my board. It has been simulated with proteus. There is no problem with the circuit measurement when soldering the circuit, but there is no response w...
lecdyx312 51mcu
What is the status of the STM32 pin after setting it to push-pull output?
I have a question!After the STM32 pin is reset, it is in high impedance input state. Then I configure the pin as push-pull output.But it does not assign a valueof 0 or 1. Does it output 0 or 1 at this...
niuqingjun stm32/stm8
SensorTile.boxr's personal experience
I just received my engineer's certificate. It took me two years to pass the exam and I finally got it after retaking it .Let’s get to the point It has been more than half a month since I received it. ...
黎某西 ST MEMS Sensor Creative Design Competition

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2758  730  2707  326  2293  56  15  55  7  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号