EEWORLDEEWORLDEEWORLD

Part Number

Search

HIP2123FRTBZ

Description
100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer
File Size710KB,16 Pages
ManufacturerIntersil ( Renesas )
Websitehttp://www.intersil.com/cda/home/
Download Datasheet Compare View All

HIP2123FRTBZ Online Shopping

Suppliers Part Number Price MOQ In stock  
HIP2123FRTBZ - - View Buy Now

HIP2123FRTBZ Overview

100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer

HIP2122, HIP2123
NOT RECOMMENDED FOR NEW DESIGNS
NO RECOMMENDED REPLACEMENT
contact our Technical Support Center at
1-888-INTERSIL or www.intersil.com/tsc
DATASHEET
FN7670
Rev 0.00
December 23, 2011
100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer
The HIP2122 and HIP2123 are 100V, high frequency, half-
bridge MOSFET driver ICs. They are based on the popular
ISL2100A and ISL2101A half-bridge drivers. Like the
ISL2100A, two logic inputs, LI and HI, control both bridge
outputs, LO and HO. All logic inputs are V
DD
tolerant.
These drivers have a programmable dead-time to insure
break-before-make operation between the high-side and low-
side drivers. The dead-time is adjustable up to 220ns. The
internal logic does not prevent both outputs from turning on
simultaneously if both inputs are high simultaneously for a
time greater than the programmed delay.
A single PWM logic input controls both bridge outputs (HO, LO).
An enable pin (EN), when low, drives both outputs to a low
state. All logic inputs are V
DD
tolerant and the HIP2122 has
CMOS inputs with hysteresis for superior operation in noisy
environments.
The HIP2122 has hysteretic inputs with thresholds that are
proportional to V
DD
. The HIP2123 has 3.3V logic/TTL
compatible inputs.
Two package options are provided. The 10 lead 4x4 DFN
package has standard pinouts. The 9 lead 4x4 DFN package
omits pin 2 to comply with 100V conductor spacing per IPC-
2221.
Features
• 9 Ld TDFN “B” Package Compliant with 100V Conductor
Spacing Guidelines per IPC-2221
• Break-Before-Make Dead-Time Prevents Shoot-through and
is adjustable up to 220ns
• Bootstrap Supply Max Voltage to 114VDC
• Wide Supply Voltage Range (8V to 14V)
• Supply Undervoltage Protection
• CMOS Compatible Input Thresholds with Hysteresis
(HIP2122)
• 1.6/1 Typical Output Pull-up/Pull-down Resistance
• On-Chip 1Ω Bootstrap Diode
Applications
• Telecom Half-Bridge DC/DC Converters
• UPS and Inverters
• Motor Drives
• Class-D Amplifiers
• Forward Converter with Active Clamp
Related Literature
FN7668,
HIP2120, HIP2121 “100V, 2A Peak, High
Frequency Half-Bridge Drivers with Adjustable Dead Time
Control and PWM Input”
HALF
BRIDGE
100V MAX
HIP2122, HIP2123
VDD
HI
HB
HO
HS
RDT
VSS
EPAD
LO
FEEDBACK
WITH
ISOLATION
SECONDARY
CIRCUITS
DEADTIME (ns)
200
160
140
120
100
80
60
40
PWM
CONTROLLER
LI
20
8
16
24
32
RDT (kΩ)
40 48 56 64 80
FIGURE 1. TYPICAL APPLICATION
FIGURE 2. DEAD-TIME vs TIMING RESISTOR
FN7670 Rev 0.00
December 23, 2011
Page 1 of 16

HIP2123FRTBZ Related Products

HIP2123FRTBZ HIP2122 HIP2122FRTAZ HIP2123
Description 100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer 100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer 100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer 100V, 2A Peak, High Frequency Half-Bridge Drivers with Rising Edge Delay Timer
Why does each file generate such an alarm after I compile it with 340A?
Why does each file generate such a warning after I compile it with 340A?Warning[Pe001]: last line of file ends without a newline...
lingqiang0123 Microcontroller MCU
Power MOSFET Tutorial - Reprint
As we all know, due to the insulated gate, power MOSFET devices require very little drive power and have excellent switching speed, with the characteristics of "ideal switch". Its main disadvantages a...
trevor Power technology
[Obtaining the initial rotor position of a permanent magnet synchronous motor starting with a rotary encoder]
[i=s]This post was last edited by jonny0811 on 2015-11-23 16:06[/i] I am here to bother you again today. When the permanent magnet synchronous motor is started, how is the rotor position detected? If ...
jonny0811 Integrated technical exchanges
[Posting Notes] 2022 Digi-Key Innovation Design Competition
The shortlisted guys, when you post unboxing posts or share the DIY process,1. "Post Topic Category" Please select [Experience Sharing] The title should be: [Creative name] + shared content Example: [...
EEWORLD社区 DigiKey Technology Zone
200M RF amplifier
Dear experts, I want to make a 200M RF power amplifier, with an output power of about 1-4W and an output voltage of about 10V. Do you have any recommended amplifier chips or modules? Thank you very mu...
x282718 RF/Wirelessly
Guess what Vout is in the picture? (3)
[color=#333333][font=Arial, Helvetica, sans-serif]Give you three options: A, 1V; B, 1.5V; C, uncertain. [/font][/color]Everyone answer first, then look back at the answer:) [hide](1) Why is Vout not 1...
maylove Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2171  478  2545  1147  677  44  10  52  24  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号