UT54ACTS169-UQCR

Remarks: Focus on IoT application development and share IoT technology experience. Software platform: IAR6.5 TCP/IP protocol stack: LWIP1.4.1 Hardware platform: STM32F103C8T6 wired communication ...[Details]

I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]

introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]

Different from 51, AVR and other single-chip microcomputers, the clock signal sources of msp430 include LFXT1, XT2 and DCO. 1. LFXT1: It can connect high-speed and low-speed crystal oscillators. In l...[Details]

On May 8, Google I/O 2018 Developer Conference was held as scheduled in Mountain View, California. In the second year of the full promotion of the "AI first" strategy, artificial intelligen...[Details]

Site conditions: 1. AD acquisition, DMA transmission; AD is set to single-channel continuous mode, DMA is set to single-shot mode. The upper threshold of the AD analog watchdog setting is less than t...[Details]

1. Function and purpose         There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]

ORG 0000H LJMP MAIN ORG 0003H LJMP TOINT ORG 001BH LJMP TOINT1 ORG 0030HMAIN: MOV SP,#60H      SETB IT0      SETB EX0      SETB EA      SJMP $TOINT:MOV TMOD,#10H      MOV TH1,#0FEH      MOV TL1...[Details]

#include reg52.h #define PORTLEN P0 sbit bit_select = P2^0; sbit seg_select = P2^1; unsigned char src = {0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f ,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71}; unsigne...[Details]

;Question: The 80C51 single-chip microcomputer has a fosc = 6MHz. It is required to use the T1 timer working mode 1 to perform a timing of 40ms. And P1.7 periodically outputs a rectangular wave with ...[Details]

Manually assemble the following program machine code and analyze the execution function of the program segment.       CLR A       MOV R2, A       MOV R7, #4 LOOP:      CLR C       MOV A, R0       RLC...[Details]

It is required to use timer/counter 1 for timing, with a timing of 1 second; timer/counter 0 for counter, and the external pulse to be counted is connected from P3.4 (T0). The microcontroller will co...[Details]

#include  #include   #define uchar unsigned char #define uint unsigned int uchar int_flag; uint qian,bai,shi,ge; uint i; float distance;   // Alphanumeric LCD Module functions #asm    .equ __lcd_port...[Details]

HT47I_O Port Application include ht47c20.inc data .section 'data' count db ? code .section at 0 'code'  org 00h  jmp start  org 04h  reti  org 08h    reti  org 0ch  reti  org 10h  jmp timer_int ;***...[Details]

EUV lithography technology will be introduced to 10nm and 7nm process nodes in the next few years. However, according to the analysis released at the ISS 2018 held in California, the ...[Details]