EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63115-520

Description
Bus Driver/Transceiver
Categorylogic    logic   
File Size124KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63115-520 Overview

Bus Driver/Transceiver

BUS-63115-520 Parametric

Parameter NameAttribute value
MakerData Device Corporation
Reach Compliance Codecompliant
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
Single chip digital multimeter + program (already made into a physical object)
[i=s] This post was last edited by 158999437 on 2015-5-1 14:59 [/i] The board is also completed, hope to share with you! DC: 0~100V AC: 0~100V DC: 0~1a AC: 0~1a Resistance and current are made by 555 ...
158999437 Download Centre
Model 2602 SourceMeter for VCSEL DC Production Testing - Equipment List
Basic EquipmentModel2602 Dual Channel SourceMeter System (for laser diode bias voltage output and photocurrent testing in a single chassis)2510-AT TEC Source Meter (Laser Diode Temperature Control)250...
Jack_ma Test/Measurement
Application of TPS61046 dual output in optical communication
Abstract Optical communication applications often need to boost the +3.3V input power supply to obtain a set of positive and negative voltages, such as +/-20V. The common practice is to use two chips ...
灞波儿奔 Energy Infrastructure?
A strange question about an experiment in Yu Zhennan's book
First the code:UINT8 znFAT_Enter_Dir2(INT8 *dirpath,UINT32 *pCluster,UINT32 *pos) { UINT8 index=0,res=0; UINT32 i=1; // #ifndef USE_LFN INT8 dirname[13]; // #else // INT8 dirname[MAX_LFN_LEN+1]; // #e...
chenbingjy stm32/stm8
BeagleBone Black design: BBB baseboard adds capacitive screen and tslib test!
[i=s]This post was last edited by anananjjj on 2014-5-20 15:45[/i] My joystick uses ADC sampling, and the built-in resistive screen uses ADC. I don't know why, it suddenly doesn't work properly! So I ...
anananjjj DSP and ARM Processors
The basic astable circuit composed of dual triodes is incomprehensible~~
Because I need a flashing circuit. Since there is no special requirement, as long as it can flash, I thought of using the simplest circuit form: It is an astable circuit consisting of two transistors ...
辛昕 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2525  1921  1910  2200  1830  51  39  45  37  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号